amber connect ACC210 Bedienungsanleitung
Quick Start Guide
ACC210
Amber Covert C210
Smart GNSS Tracker
1. Warranty
●The warranty is valid only when the warranty card is properly completed, and upon presentation
of the proof of purchase consisting of the original invoice indicating the date of purchase, model
and serial No. of the product. We reserve the right to refuse warranty if this information has been
removed or changed after the original purchase of the product from the dealer.
●Our obligations are limited to repair of the defect or replacement of the defective part or at its
discretion replacement of the product itself.
●Warranty repairs must be carried out by our Authorized Service Centre. Warranty cover will be
void, even if a repair has been attempted by any unauthorized service centre.
●Repair or replacement under the terms of this warranty does not provide right to extension or
renewal of the warranty period.
●The warranty is not applicable to cases other than defects in material, design and workmanship.
2. Maintenance Record
Date
Serviced by
Product Model
IMEI Number
Fault Description
Comments
3. Troubleshooting
Type
Use
Unable to connect to
tracking platform
Check the APN and IP settings. Check whether the
data service or SIM card is enabled.
Check the balance of SIM card.
Tracker shows offline
Check whether external power is still connected.
Check if the vehicle entered a network blind area.
Check the balance of SIM card.
Unable to locate
Make sure the top side is facing upward without
metallic things shielded.
Make sure it's not in an area with no satellite coverage.
Location drift
In areas with poor GNSS signal {la11 building around
or basement), drifting may happen. Check whether
vibration happens around to trigger the accelerator.
No command reply
Make sure the command format is correct. Vehicle
may be in a network blind area.
Make sure the SIM card is well inserted and has SMS
service.
●In areas with poor GNSS signal {la11 building around or basement), drifting may happen.
Check whether vibration happens around to trigger the accelerator
Loss of traction alert
●When the vehicle changes the course angle for more than 3 seconds at an angular velocity
greater than 20• Is, the device will send an alert to the platform.
Vehicle angle abnormality
●When the vehicle rolling angle is greater than 20° and less than 70°, the device will send an
alert to the platform.
4. Driver behavior monitoring
Device support detects eight types of driver behaviors, which are transmitted by GPRS and can be
displayed on the server.
●Harsh acceleration alert
The device defines harsh acceleration as occurring when the vehicle's speed increases sharply. An alert
will be sent to the platform. E.g: The vehicle's speed increases from 0KM/H to 50KM/H after 2
seconds of engine start.
●Harsh brake alert
The device defines harsh braking as occurring when the vehicle's speed decreases sharply. An alert will
be sent to the platform. E.g: The vehicle's speed drops from 50KM/H to 10KM/H after 2 seconds of
emergency braking.
●Sharp turn alert
The device defines sharp tum as occurring when the vehicle makes a high-speed turn. An alert will be
sent to the platform. E.g: The driving speed is greater than 30KM/H, and the angle change is greater
than 90°.
●Harsh lane change alert
The device defines harsh lane change as occurring when the vehicle suddenly changes lanes at high
speed. An alert will be sent to the platform. E.g: The driving speed is greater than 60KM/H, and the
angle change is less than 20°.
●Crash alert
If collision occurs, the device will send an alert to the platform.
5. Over-speed alert (Default OFF)
To cut-off/restore the fuel by SMS command, you have to authorize a center number.
Set the center number: CENTER,A,mobile number#
Delete the center number: CENTER,D#
Notice:
Only the preset SOS number can set/delete the center number.
Only one center number can be set.
To cut-off fuel/power connection: RELAY.A#
A=0/1 (O=restore fuel; 1 =cut-off fuel) Default value: 0
E.g.RELAY,1#
Over-speed alert (Default OFF)
SPEED,S,T,SPEED,M#
8=1 means ON; S=O means OFF
T means duration of speeding, ranges 5-600 (second)
SPEED ranges 1-255 (KM/H)
M means alert way
M=1 SMS+GPRS; M=O means GPRS
E.g. SPEED,ON,20,100,1#
When vehicle speed is over 100KM/H for 10 seconds, you will receive an SMS and GPRS alert on the
server.
Note: SPEED.OFF# Disable over-speed alert
6. GPS upload interval setting
By time interval (Default Valid)
TIMER,T1, T2#
●Tl means upload interval when ACC ON
●T2 means upload interval when ACC OFF
●Range: 5-18000 or O (second); O means no upload
●Default valid setting: TIMER, 10, 10#
●Query current TIMER setting: TIMER#
By distance interval (Default OFF)
DISTANCE,D#
●D ranges 50-10000 or 0 (meters)
Note: If the user enables uploading by DISTANCE, the preset TIME uploading turns invalid.
7. SOS emergency call (with 6-pin power cable)
In case of emergency, press SOS for 3 seconds to activate SOS alert. The device will send an SMS
alert to preset SOS numbers and dial the numbers in a loop for three times until the call is picked up.
Ala nm message will also be sent to the tracking platform.
To add SOS number: SOS,A,number1 ,number2,number3#
To delete the SOS number: SOS,D,phone number#
Query SOS number: SOS#
8. Remote power/fuel cut-off (with 6-pin power cable)
If the vehicle is stolen, a fuel/power command can be sent by platform, APP or SMS.
Notice:
●Make sure ACC is correctly connected.
●When ACC is OFF, command will be executed immediately.
●When ACC is ON but GPS is not fixed, command will defer.
●When ACC is ON and GPS is fixed, command will be executed when vehicle speed is less
than 20kmlh.
9. Product overview
GPS
Power
GSM
10. INS (lnertial Navigation System)
INS can be used as a fallback in weak or unavailable GPS signal areas, e.g. underpass, tunnel,
downtown.
11. Driver behavior analysis
●Harsh acceleration alert
●Harsh braking alert
●Harsh cornering alert
●Sudden lane change alert
●Collision alert
●Skidding alert
●Rollover alert
●Roll and pitch alert
12. Position tracking
●GPS & LBS positioning
●Real-time location query
Easy self-installation
13. Specification
GSM Band
850/900/1800/1900 MHz
GNSS Type
GPS+INS (lnertial navigation system)
Antenna
Built-in GPS ceramic antenna; GSM
quad-band antenna
LED indicator
GPS(blue), GSM(green), Power(red)
Battery
450mAh/3. 7V Li-Polymer battery
Working voltage/current
9-36VDC/38mA(12VDC)
Standby time
28 hours
Working time
1.5 hours
Operating temperature
-20°C to 70°C
Weight
63g
Dimension
80.0 x 67.0 x 16.0mm
14. Standard Parts list
Item
Quantity
JM-VG01U
1
6-pin power cable
1
Hook & loop fastener
1
Relay
1
Panic button
1
15. Product setup
Insert SIM and Power on
●Choose the Micro SIM card with SMS and GPRS access.
●Remove the front cover and toggle the switch to OFF.
●Insert the SIM card into the card slot with its gold-plated contacts
towards the Printed Circuit Board.
●Toggle the battery switch to ON and return the cover.
16. LED indications
Power Status (Red)
Behavior Meaning
Quick blinking Low internal battery
Slow blinking Normal mode
Solid on The device is charging
Off Power off or battery error
GNSS Status (Blue)
Behavior Meaning
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere amber connect GPS Handbücher
amber connect
amber connect ATC400 Bedienungsanleitung
amber connect
amber connect Amber Power T300 Bedienungsanleitung
amber connect
amber connect Amber Insight T450-Ia Bedienungsanleitung
amber connect
amber connect Amber Insight C450 Bedienungsanleitung
amber connect
amber connect AMB375 Bedienungsanleitung
amber connect
amber connect Amber Guard T210 Bedienungsanleitung
amber connect
amber connect Amber Covert C412 Bedienungsanleitung
amber connect
amber connect Instant C200 Bedienungsanleitung
amber connect
amber connect ACC400-E/LA Bedienungsanleitung
amber connect
amber connect C420 Bedienungsanleitung
amber connect
amber connect AMB363N Bedienungsanleitung
amber connect
amber connect Amber Power C210 Bedienungsanleitung
amber connect
amber connect AMB377 Bedienungsanleitung
amber connect
amber connect Amber Insight T251 Bedienungsanleitung
amber connect
amber connect APC300 Bedienungsanleitung
amber connect
amber connect Amber Covert C300 Bedienungsanleitung
amber connect
amber connect Amber Swift C300 Bedienungsanleitung
amber connect
amber connect Amber Guard A 100 Bedienungsanleitung
amber connect
amber connect Amber Swift A100 Bedienungsanleitung
amber connect
amber connect Amber Covert C413 Bedienungsanleitung
