American DJ Inno Color Beam Z7 Bedienungsanleitung

User Instructions

10/13

specications, diagrams, images, and instructions herein are

subject to change without notice. ADJ Products, LLC logo and

identifying product names and numbers herein are trademarks

of ADJ Products, LLC. Copyright protection claimed includes all

forms and matters of copyrightable materials and information

now allowed by statutory or judicial law or hereinafter granted.

Product names used in this document may be trademarks or

registered trademarks of their respective companies and are

hereby acknowledged. All non-ADJ Products, LLC brands and

product names are trademarks or registered trademarks of their

respective companies.

ADJ Products, LLC and all aliated companies hereby dis-

claim any and all liabilities for property, equipment, building, and

electrical damages, injuries to any persons, and direct or indi-

rect economic loss associated with the use or reliance of any

information contained within this document, and/or as a result

of the improper, unsafe, unsucient and negligent assembly,

installation, rigging, and operation of this product.

Inno Color Beam Z7

ADJ Products, LLC - www.adj.com - Inno Color Beam Z7 User Manual Page 3ADJ Products, LLC - www.adj.com - Inno Color Beam Z7 User Manual Page 2

• RGBW Color Mixing

• 7 x 10W High Quatlity Osram LEDs

• Color Strobe Effect

• Color Mix Effect

• Pan/Tilt Inversion

• Electronic Dimming 0-100%

• Dimmer Curve

• Built in Microphone

• DMX-512 protocol

• 14 DMX Channels

• 3 Operating Modes - Sound Active, Show Mode, or DMX Control

• Power Cord Daisy Chaining (See Section Below)

Inno Color Beam Z7 Warranty Registration

The Inno Color Beam Z7 carries a 3 year (1095 days) limited warranty.

Please fill out the enclosed warranty card to validate your purchase

and warranty. You may also register your product online at www.

americandj.com. All returned service items whether under warranty or

not, must be freight pre-paid and accompany a return authorization

(R.A.) number. If the unit is under warranty you must provide a copy

of your proof of purchase invoice. Please contact ADJ customer sup-

port for a R.A. number.

Inno Color Beam Z7 Features

To optimize the performance of this product, please read these operat-

ing instructions carefully to familiarize yourself with the basic operations

of this unit. These instructions contain important safety information

regarding the use and maintenance of this unit. Please keep this manual

with the unit, for future reference.

Inno Color Beam Z7 General Instructions

Inno Color Beam Z7 Introduction

Unpacking: Thank you for purchasing the Inno Color Beam Z7 by

ADJ Products, LLC. Every Inno Color Beam Z7 has been thoroughly

tested and has been shipped in perfect operating condition. Carefully

check the shipping carton for damage that may have occurred during

shipping. If the carton appears to be damaged, carefully inspect your

xture for any damage and be sure all accessories necessary to oper-

ate the unit has arrived intact. In the case damage has been found

or parts are missing, please contact our toll free customer support

number for further instructions. Do not return this unit to your dealer

without rst contacting customer support.

Introduction: The Inno Color Beam Z7 is part of ADJ’s continuing

pursuit for creating high quality affordable intelligent fixtures. The Inno

Color Beam Z7 is a high performance, DMX intelligent, moving head

LED fixture. This fixture is a great piece for retail stores, displays, mood,

architectural, interior and exterior decoration, and clubs. This unit can

be used as a stand alone, or in a Master/Slave conguration. The unit

can also be controlled via DMX controller. This fixture is suitable for

theaters, studios, retail stores, and other similar locations.

Customer Support: ADJ Products, LLC provides a toll free cus-

tomer support line, to provide set up help and to answer any question

should you encounter problems during your set up or initial operation.

You may also visit us on the web at www.adj.com for any comments

or suggestions. Service Hours are Monday through Friday 8:00 a.m. to

4:30 p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2941

E-mail: [email protected]

To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact

ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

Inno Color Beam Z7 Power Cord Daisy Chaining

With this feature you can connect the xtures to one another

using the IEC input and output sockets. The quantity that can be

connected is 4 xtures maximum for 120V and 8 xtures maxi-

mum for 240V. After the maximum xtures has been reached you

will need to use a new power outlet. They must be the same x-

tures. DO NOT mix xtures.

ADJ Products, LLC - www.adj.com - Inno Color Beam Z7 User Manual Page 4 ADJ Products, LLC - www.adj.com - Inno Color Beam Z7 User Manual Page 5

Inno Color Beam Z7 Safety Precautions

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt-

age for your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken. Do not attempt to remove or break o the ground

prong from the electrical cord. This prong is used to reduce the risk

of electrical shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out`

doors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to the point they exit from the unit.

• Cleaning -The fixture should be cleaned only as recommended by

t he manufacturer. See page 22 for cleaning details.

• Heat -The appliance should be situated away from heat sources

such as radiators, heat registers, stoves, or other appliances (inclu-

d ing amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the appliance.

C. The appliance has been exposed to rain or water.

D. The appliance does not appear to operate normally or exhibits a

marked change in performance.

The Inno Color Beam Z7 is fully operational in two dierent mounting

positions, hanging upside-down from a ceiling or set on a at level

surface. To avoid internal damage to the unit, never mount the unit on

its side as illustrated above. Be sure this xture is kept at least 0.5m

away from any ammable materials (decoration etc.). Always use

and install the supplied safety cable as a safety measure to prevent

accidental damage and/or injury in the event the clamp fails (see next

page). Never use the carrying handles for secondary attachment.

When installing the unit, the trussing or area of installation must be

able to hold 10 times the weight without any deformation. When

installing the unit must be secured with a secondary safety attach-

ment, e.g. and appropriate safety cable. Never stand directly below

the unit when mounting, removing, or servicing the unit.

Overhead mounting requires extensive experience, including calculat-

ing working load limits, installation material being used, and perodic

safety inspection of all installation material and unit. If you lack these

qualications, do not attempt the installation yourself.

These installaiton should be checked by a skilled person once a year.

Inno Color Beam Z7 Installation

ADJ Products, LLC® - www.adj.com - Inno Color Beam Z7 User Manual Page 6 ADJ Products, LLC - www.adj.com - Inno Color Beam Z7 User Manual Page 7

Power Supply: The ADJ Inno Color Beam Z7 contains a automatic

voltage switch, which will auto sense the voltage when it is plugged

into a power source. With this switch there is no need to worry about

the correct power voltage, this unit can be plugged in anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used as a form of communication between intelligent fixtures

and controllers. A DMX controller sends DMX data instructions from

the controller to the fixture. DMX data is sent as serial data that trav-

els from fixture to fixture via the DATA “IN” and DATA “OUT” XLR ter-

minals located on all DMX fixtures (most controllers only have a DATA

“OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of

dierent manufactures to be linked together and operate from a single

controller, as long as all xtures and the controller are DMX compli-

ant. To ensure proper DMX data transmission, when using several

DMX fixtures try to use the shortest cable path possible. The order

in which fixtures are connected in a DMX line does not influence the

DMX addressing. For example; a fixture assigned a DMX address of 1

may be placed anywhere in a DMX line, at the beginning, at the end,

or anywhere in the middle. When a fixture is assigned a DMX address

of 1, the DMX controller knows to send DATA assigned to address 1

to that unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation):

The Inno Color Beam Z7 can be controlled via DMX-512 protocol. The

Inno Color Beam Z7 is a 14 Channel DMX unit. The DMX address is

set on the front panel of the Inno Color Beam Z7. Your unit and your

DMX controller require a approved DMX-512 110 Ohm Data cable for

data input and data output (Figure 1). We recommend Accu-Cable

DMX cables. If you are making your own cables,

be sure to use standard 110-120 Ohm shielded

cable (This cable may be purchased at almost

all professional sound and lighting stores). Your

cables should be made with a male and female

XLR connector on either end of the cable. Also

remember that DMX cable must be daisy chained

and cannot be split.

Inno Color Beam Z7 Set Up

Figure 1

Screw one clamp via a M12 screw and nut onto the Omega

holder. Insert the quick-lock fasteners of the rst Omega holder

into the respective holes on the bottom of the Inno Color Beam

Z7. Tighten the quick-lock fasteners fully clockwise. Pull the

safety-cable through the two slots located on the base under-

neath the Omega holder and then over the trussing system or a

safe xation spot. Insert the end in the carabine and tighten the

safety screw.

NOTICE: The suitable enviromental temperature for this light-

ing xture is between -25˚ C to 45˚ C. Do not place this lighting

xture in an enviroment where the temperatures are under or

above the temperatures stated above. This will allow the xture

to run at its best and help prolong the xture life.

Inno Color Beam Z7 Installation

ADJ Products, LLC - www.adj.com - Inno Color Beam Z7 User Manual Page 8 ADJ Products, LLC - www.adj.com - Inno Color Beam Z7 User Manual Page 9

Inno Color Beam Z7 System Menu

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

Figure 3

1 Ground 1 Ground

XLR Male Socket

XLR Pin Conguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic

behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 4

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin XLR

connectors for DATA transmission in place of 3-pin. 5-pin XLR xtures

may be implemented in a 3-pin XLR DMX line. When inserting standard

5-pin XLR connectors in to a 3-pin line a cable adaptor must be used,

these adaptors are readily available at most electric stores. The chart

below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

Inno Color Beam Z7 Set Up

DMX Address

Sound Sense

Show Mode

Function Delay

Dimmer Curve

Pan Inverse

Slave Mode

Black Out

Sound State

Tilt Inverse

Back Light

White Balance

Manual Test

Auto Test

Reset

Fixture Time

PRO de faults

Firmware Version

Temp.

00 1

125

Show 1

No De lay

Stan dard

Show 2

1s De lay

2s De lay

3s De lay

Stag e

Show 3

Show 4

Arch itec

Th eatr e

Yes

Sl ave 1

Yes

Sl ave 2

Off

Red

Green

Blue

Pan

Tilt

Zoom

Strobe

Red

Blue

Wh ite

Dimmer

Gre en

512

100

255

25 5

ADJ Products, LLC - www.adj.com - Inno Color Beam Z7 User Manual Page 11ADJ Products, LLC - www.adj.com - Inno Color Beam Z7 User Manual Page 10

Inno Color Beam Z7 System Menu

is displayed, press ENTER to conm.

NOTE: In a Master/Slave conguration you can make one x-

ture the Master and then set the next xture to “Slave 2”, the

xtures will now have contrast movement to each other.

Black Out - This will activate/deactivate blackout

1. Press the MENU button until “Black Out” is displayed, press

ENTER.

2. Either “Yes” or “No” will now be displayed. Press the UP or

DOWN buttons to toggle between “Yes” and “No”.

3. Press ENTER to conrm your setting.

Sound State - In this mode the unit will run in sound

active mode.

1. Press the MENU button until “Sound State” is displayed, press

ENTER.

2. Either “On” or “O” will now be displayed. Use the UP or

DOWN buttons to toggle between “On” and “O”.

3. Press ENTER to conrm your selection, the press and hold the

MENU button to activate.

Sound Sense - In this mode you can adjust the sound

sensitivity of the sound active mode.

1. Press the MENU button until “Sound Sense” is displayed,

press ENTER.

2. Press the UP or DOWN buttons to adjust the sensitivity level.

The sensitivity level can be adjusted between 0 (the lowest) and

100 (most sensitive).

3. Press ENTER to set you desired level.

Inno Color Beam Z7 System Menu

DMX Address - Set the DMX Address -

1. Press the MENU button until “DMX Addresss” is displayed,

press ENTER.

2. “X” will now be displayed, “X” represents the displayed address.

Press the UP or DOWN buttons to nd your desired address.

3. Press ENTER to conrm, and then press and hold the MENU

button for at least three seconds to assign.

Show Mode - Show modes 1 - 4 (Factory Shows).

1. Press the MENU button until “Show Mode” is displayed, press

ENTER.

2. “Show X” will now be displayed, “X” representing a number

between 1-4. Press the UP or DOWN buttons to nd your desired

show and press ENTER to conrm. After pressing ENTER, press

and hold the MENU button for at least 3 seconds to activate.

Dimmer Curve - In this mode you can select the dimmer

curve.

1. Press the MENU button until “Dimmer Curve” is displayed,

press ENTER.

2. The current dimmer curve will be displayed.

3. Press the UP or DOWN buttons to nd your desired dimmer

curve and press ENTER to conrm.

Slave Mode - This will let you set unit as a master or

slave in a master/slave conguration.

1. Press the MENU button until “Slave Mode” is displayed,

press ENTER. Either “Slave 1” or “Slave 2” will be displayed.

2. Press the UP or DOWN buttons until your desired slave mode

ADJ Products, LLC - www.adj.com - Inno Color Beam Z7 User Manual Page 13ADJ Products, LLC - www.adj.com - Inno Color Beam Z7 User Manual Page 12

This number represents the delay setting. Use the UP and DOWN

buttons to adjust the blackout delay.

Example: If the delay is set to 3 seconds, when you are in 14

Channel mode under DMX control, and the channel 12 values are

between 226-235, the xture will move, and then blackout after

3 seconds.

3. Press ENTER to conrm.

White Balance - With this function you can adjust the

RGB colors to make your desired color.

1. Press the MENU button until “White Balance” is displayed,

press ENTER.

2. Use the UP or DOWN buttons to nd the color you wish to

adjust.

3. Once you nd the color you want to adjust press ENTER, the

displayed value will begin to ash. Use the UP or DOWN but-

tons to adjust the value. Once you have made your adjustment

press ENTER.

4. Repeat steps 2-3 until satised.

Manual Test - With this function you can manually test

the individual features.

1. Press the MENU button until “Manual Test” is displayed,

press ENTER.

2. Use the UP or DOWN buttons to nd the functions or colors

that you wish to test. You can test the strobe function, dimmer,

and zoom.

3. Once you nd a function or color you wish to test, press the

ENTER button, the displayed value will begin to ash. You can

now adjust the values by pressing the UP and DOWN buttons.

Inno Color Beam Z7 System MenuInno Color Beam Z7 System Menu

Pan Inverse - Pan Inversion

1. Press the MENU button until “Pan Inverse” is displayed,

press ENTER. Either “Yes” or “No” will be displayed.

2. To activate the Pan inversion press the UP or DOWN buttons

until “Yes” is displayed, press ENTER to conm. To deactivate

Pan inversion, select “No” and press Enter.

Tilt Inverse - Tilt Inversion

1. Press the MENU button until “Tilt Inverse” is displayed, press

ENTER. Either “Yes” or “No” will be displayed.

2. To activate the Tilt inversion press the UP or DOWN buttons

until “Yes” is displayed, press ENTER to conm. To deactivate

Tilt inversion, select “No” and press Enter.

Back Light - With this function you can make the back-

light automatically turn off after one minute.

1. Press the MENU button until “Back Light” is displayed, press

ENTER.

2. Either “ON” or “OFF” will now be displayed. Press the UP or

DOWN buttons to select “ON” to keep the backlight on at all

times, or “OFF” to allow the backlight to turn o after 2 minutes.

Press any button to turn the backlight on again.

3. Press ENTER to conrm.

Function Delay - With this function the blackout func-

tion under 14 Channel mode can be delayed.

1. Press the MENU button until “Function Delay” is displayed,

press ENTER.

2. Either “No Delay” or time between 1s - 3s will be displayed.

ADJ Products, LLC - www.adj.com - Inno Color Beam Z7 User Manual Page 14 ADJ Products, LLC - www.adj.com - Inno Color Beam Z7 User Manual Page 15

Once you have nished testing press the ENTER button.

4. To exit the manual test mode, press the MENU button.

Auto Test - This function will run a self test program.

1. Press the MENU button until “Auto Test” is displayed, press

ENTER.

2. The xture will now run a self test. Press the MENU button to

exit.

Temp. - With this function you can display the running

temperature of the unit.

1. Press the MENU button until “Temp.” is displayed, press

ENTER.

2. The current running temperature of the xture will now be dis-

played. Press MENU to exit.

Fixture Time - With this function you can display the

running time of the unit.

1. Press the MENU button until “Fixture Time” is displayed,

press ENTER.

2. The running time of the xture will now be displayed. Press

MENU to exit.

Firmware Version - This will display the software ver-

sion

1. Press the MENU button until “Firmware Version” is displayed.

Press the ENTER button and the software vesion will be dis-

played.

2. Press the MENU button to leave this function.

Inno Color Beam Z7 System Menu

PRO Default - This function will restore the factory set-

tings.

1. Press the MENU button until “PRO Default” is displayed,

press ENTER.

2. Either “YES” or “NO” will now be displayed. Press the UP or

DOWN buttons to select “YES” to switch back to defualt set-

tings, and press ENTER.

Reset - Use this function to reset the motors.

1. Tap the MENU button until “Reset” is displayed, press

ENTER.

2. The xture will now reset the motors.

Inno Color Beam Z7 System Menu

Inno Color Beam Z7 UC3 Control

Stand by The unit blackout

Function 1. Sync. Strobe

2. 2 light strobe

3. sound strobe

Select

Show

1-4

1. Hold to change Master Pan position

2. Hold to change Master Tilt position

3. Hold to change Master Dimmer

4. Hold to change Slave Pan position

5. Hold to change Slave Tilt position

6. Hold to change Slave Dimmer

Mode Sound (LED off)

LED on LED fast blinking

ADJ Products, LLC - www.adj.com - Inno Color Beam Z7 User Manual Page 17ADJ Products, LLC - www.adj.com - Inno Color Beam Z7 User Manual Page 16

Universal DMX Control: This function allows you to use a Elation®

universal DMX-512 controller to control the chases and patterns,

dimmer and strobe. A DMX controller allows you to create unique

programs tailored to your individual needs. The Inno Color Beam Z7

has 14 DMX Channels.

1. This function will allow you to control each individual fixture’s

traits with a standard DMX 512 controller. See pages 17-20 for

the DMX traits.

2. To run your fixture in DMX mode, set your desired DMX address

following the directions on page 10, and the set-up specifications

that come with your DMX controller.

3. Plug in the fixture via the XLR connections to any standard DMX

controller.

4. For longer cable runs (more than a 100 feet) use a terminator on

the last fixture.

Inno Color Beam Z7 Universal DMX Control

Master-Slave Conguration: This function will allow you to link up

to 16 units together and operate without a controller. The units will be

sound activated. In Master-Slave operation one unit will act as the con-

trolling unit and the others will react to the controlling units programs.

Any unit can act as a Master or as a Slave.

1. Using approved DMX data cables, daisy chain your units togeth-

er via the XLR connector on the rear of the units. Remember the

Male XLR connector is the input and the Female XLR connector

is the output. The rst unit in the chain (master) will use the female

XLR connector only - The last unit in the chain will use the male

XLR connector only. For longer cable runs we suggest a termina-

tor at the last fixture.

2. Set the Master unit to your desired operating mode.

3. On the slave units press the MENU button until “Slave Mode” is

displayed, and Press ENTER. Choose either “Slave 1” or “Slave 2”

and press ENTER. See page 11 for more info.

4. The slave units will now follow the Master unit.

Inno Color Beam Z7 Master-Slave Configuration

Channel Value Function

1 PAN

0 - 255 0° - 540°

2 0 - 255 PAN FINE

3 TILT

0 - 255 0° - 220°

4 0 - 255 TILT FINE

5 RED

0 - 255 0% - 100%

6 GREEN

0 - 255 0% - 100%

7 BLUE

0 - 255 0% - 100%

8 WHITE

0 - 255 0% - 100%

9 COLOR MACROS

0 OFF

1 - 4 MACRO 1

5 - 8 MACRO 2

9 - 12 MACRO 3

13 - 16 MACRO 4

17 - 20 MACRO 5

21 - 24 MACRO 6

25 - 28 MACRO 7

29 - 32 MACRO 8

33 - 36 MACRO 9

37 - 40 MACRO 10

41 - 44 MACRO 11

45 - 48 MACRO 12

49 - 52 MACRO 13

53 - 56 MACRO 14

57 - 60 MACRO 15

61 - 64 MACRO 16

65 - 68 MACRO 17

69 - 72 MACRO 18

Inno Color Beam Z7 14 Channel Mode

ADJ Products, LLC - www.adj.com - Inno Color Beam Z7 User Manual Page 18 ADJ Products, LLC - www.adj.com - Inno Color Beam Z7 User Manual Page 19

Channel Value Function

9 COLOR MACROS

73 - 76 MACRO 19

77 - 80 MACRO 20

81 - 84 MACRO 21

85 - 88 MACRO 22

89 - 92 MACRO 23

93 - 96 MACRO 24

97 - 100 MACRO 25

101 - 104 MACRO 26

105 - 108 MACRO 27

109 - 112 MACRO 28

113 - 116 MACRO 29

117 - 120 MACRO 30

121 - 124 MACRO 31

125 - 128 MACRO 32

129 - 132 MACRO 33

133 - 136 MACRO 34

137 - 140 MACRO 35

141 - 144 MACRO 36

145 - 148 MACRO 37

149 - 152 MACRO 38

153 - 156 MACRO 39

157 - 160 MACRO 40

161 - 164 MACRO 41

165 - 168 MACRO 42

169 - 172 MACRO 43

173 - 176 MACRO 44

177 - 180 MACRO 45

181 - 184 MACRO 46

185 - 188 MACRO 47

189 - 192 MACRO 48

193 - 196 MACRO 49

197 - 200 MACRO 50

201 - 204 MACRO 51

Inno Color Beam Z7 14 Channel Mode

Channel Value Function

9 COLOR MACROS

205 - 208 MACRO 52

209 - 212 MACRO 53

213 - 216 MACRO 54

217 - 220 MACRO 55

221 - 224 MACRO 56

225 - 228 MACRO 57

229 - 232 MACRO 58

233 - 236 MACRO 59

237 - 240 MACRO 60

241 - 244 MACRO 61

245 - 248 MACRO 62

249 - 252 MACRO 63

253 - 255 MACRO 64

10 SHUTTER/STROBING

0 - 19 SHUTTER CLOSED

20 - 24 OPEN

25 - 64 STROBING FAST - SLOW

65 - 69 OPEN

70 - 84 SLOW OPEN - FAST CLOSE

85 - 89 OPEN

90 - 104 FAST OPEN - SLOW CLOSE

105 - 109 OPEN

110 - 124 RANDOM STROBE

125 - 129 OPEN

130 - 144 RANDOM OPENING PULSE

145 - 149 OPEN

150 - 164 RANDOM CLOSING PULSE

165 - 169 OPEN

170 - 184 BURST PULSE

185 - 189 OPEN

190 - 204 RANDOM BURST PULSE

205 - 209 OPEN

210 - 224 PULSING

Inno Color Beam Z7 14 Channel Mode

Inhaltsverzeichnis

Andere American DJ DJ-Equipment Handbücher

American DJ

American DJ Verti-Pro II Bedienungsanleitung

American DJ

American DJ Emerald Scan Bedienungsanleitung

American DJ

American DJ Scrambler Bedienungsanleitung

American DJ

American DJ Emerald Star Bedienungsanleitung

American DJ

American DJ Jelly Par Profile Bedienungsanleitung

American DJ

American DJ Sunray Tri LED DMX Bedienungsanleitung

American DJ

American DJ Accu Spot 250 Hybrid Bedienungsanleitung

American DJ

American DJ LED Messenger Bedienungsanleitung

American DJ

American DJ Micro Phase Bedienungsanleitung

American DJ

American DJ Wave Bedienungsanleitung

American DJ

American DJ Spektra 250 Bedienungsanleitung

American DJ

American DJ UVLED Bar16 Bedienungsanleitung

American DJ

American DJ M-103HD Bedienungsanleitung

American DJ

American DJ Spiral Graph Bedienungsanleitung

American DJ

American DJ Revo XPress Bedienungsanleitung

American DJ

American DJ Saga Bedienungsanleitung

American DJ

American DJ HMI 575TM Bedienungsanleitung

American DJ

American DJ LED Trispot Bedienungsanleitung

American DJ

American DJ Tempest 250MSD Bedienungsanleitung

American DJ

American DJ Flat Par Tri7X Bedienungsanleitung

American DJ

American DJ Centurion Bedienungsanleitung

American DJ

American DJ Gobo Motion LED Bedienungsanleitung

American DJ

American DJ Color 150/RG Bedienungsanleitung

American DJ

American DJ Snow Flurry Montageanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung