American DJ Centurion Bedienungsanleitung

American DJ

4295 Charter Street

Los Angeles CA. 90058

www.americandj.com

Revised 8/01

User Instructions

Unpacking:

Thank you for purchasing the Centurion™ by American

. Every Centurion™ has been thoroughly tested and has been

shipped in perfect operating condition. Carefully check the shipping

carton for damage that may have occurred during shipping. If the

carton appears to be damaged, carefully inspect your  xture for any

damage and be sure all equipment necessary to operate the unit has

arrived intact. In the event damage has been found or parts are miss-

ing, please contact our toll free customer support number for further

instructions. Do not return this unit to your dealer without  rst contact-

ing customer support.

Introduction:

This unit use a single color/gobo wheel combination

for vibrant colors and extravagant gobo patterns. The Centurion™ is

an intelligent fixture that can operate in DMX mode, as a stand alone

sound active piece, or in a Master/Slave configuration. The Centurion™

comes with several build in programs and is best used in multiples of

four. This piece is best used with a fog or haze machine to enhance

the beam output. When used in DMX mode the fixture requires 3 DMX

channels. When used as a stand alone unit or when used in multiples

linked in a master/slave configuration an optional IRC/2 controller may

be used to control a blackout function.

Customer Support:

American DJ

provides a toll free customer sup-

port line, to provide set up help and to answer any question should you

encounter problems during your set up or initial operation. You may

also visit us on the web at www.americandj.com for any comments or

suggestions. Service Hours are Monday through Friday 9:00 a.m. to

5:00 p.m. Paci c Standard Time.

Voice:

(800) 322-6337

Fax:

(323) 582-2610

E-mail:

[email protected]

Warning!

To prevent or reduce the risk of electrical shock or  re, do

not expose this unit to rain or moisture.

Caution!

There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact

your nearest American DJ

dealer.

Centurion™ General Information

American DJ

- www.americandj.com - Centurion™ Instruction Manual Page 2

American DJ

- www.americandj.com - Centurion™ Instruction Manual Page 3

• EFP 12v/100w Lamp

• DMX-512 Compatible

• 14 Colored Gobo Combinations, Plus White Spot

• Fan Cooling.

• Built-In 15 Second Lamp Life Protection Circuitry

• Master/Slave Operation

• Linkable

Centurion™ Main Features

The Centurion™ carries a one year (365 days) limited warranty.

Please fill out the enclosed warranty card to validate your purchase.

All returned service items whether under warranty or not, must be

freight pre-paid and accompany a return authorization (R.A.) number.

If the unit is under warranty, you must provide a copy of your proof of

purchase invoice. Please contact American DJ

customer support for

a R.A. number.

Centurion™ Product Registration

•

To reduce the risk of electrical shock or  re, do not expose this unit

rain or moisture

•

Do not spill water or other liquids into or on to your unit.

•

Be sure that the local power outlet match that of the required voltage

for your unit.

•

Do not attempt to operate this unit if the power cord has been frayed

or broken.

•

Do not attempt to remove or break off the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and  re in case of an internal short.

•

Disconnect from main power before making any type of connection.

•

Do not remove the cover under any conditions. There are no user

serviceable parts inside.

•

Never operate this unit when itʼs cover is removed.

•

Never plug this unit in to a dimmer pack

•

Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

•

Do not attempt to operate this unit, if it becomes damaged.

•

This unit is intended for indoor use only, use of this product outdoors

voids all warranties.

•

During long periods of non-use, disconnect the unitʼs main power.

•

Always mount this unit in safe and stable matter.

•

Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to cords at plugs, convenience recep-

tacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 13 for cleaning details.

•

Heat -The appliance should be situated away from heat sources

such as radiators, heat registers, stoves, or other appliances (includ-

ing amplifiers) that produce heat.

•

The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the appliance.

C. The appliance has been exposed to rain or water.

D. The appliance does not appear to operate normally or exhibits a

marked change in performance.

Centurion™ Safety Precautions

American DJ

- www.americandj.com - Centurion™ Instruction Manual Page 4

To optimize the performance of this product, please read these operat-

ing instructions carefully to familiarize yourself with the basic operations

of this unit. These instructions contain important safety information

regarding the use and maintenance of this unit. If you do not wish to

read through the manual, listed below are the master/slave dip switch

setting. Link the units together using microphone cables and follow the

dip switch chart for sound activation mode. Please keep this manual

with the unit, for future reference.

Centurion™ Quick Start Instructions

Centurion™ Master/Slave Settings

This chart details the Master/Slave dip switch setting for Master/Slave

configuration. Use this configuration only when you will be using your

fixtures in a Master/Slave configuration. Be sure the number 2 function

switch is set to the on position for sound-active operation.

Head 4

Head 3

Head 2

Master - Head 1

American DJ

- www.americandj.com - Centurion™ Instruction Manual Page 6

American DJ

- www.americandj.com - Centurion™ Instruction Manual Page 5

Centurion™ Controls and Functions

REAR

Dip Switches -

These switches serve two functions. In master slave mode these

switches are used to assign a speci c head address. In DMX mode

these switches are used to assign a DMX address to the unit. In DMX

mode each switch corresponds to a speci c value based on binary

code. See page 7 for a detailed explanation of DMX binary code.

IRC/2 Controller Jack

This is for use the optional IRC/2 Black out controller only.

Do not

attempt to connect an audio signal this jack, this will damage the

PC board and void your manufactures warranty!

Microphone -

This microphone receives external low frequencies to trigger the unit in

Sound-Active and Master/Slave mode.

XLR Input Jack -

This jack is used to accept an incoming DMX signal or Master/Slave

signal.

Centurion™ Controls and Functions

XLR Output Jack -

This jack is used to transmit the incoming DMX signal to another DMX

 xture, or in master/slave mode transmit a Master/Slave signal to the

next Centurion™ in the chain. For best results in DMX or Master/Slave

mode terminate this jack if it is the last unit in the chain. See

“Termina-

tor”

on page 11.

tor” on page 11.tor”

Cooling Fan -

Keep the fan grill clean. Never block the fan vents, always allow at least

four inches between the fan and any other surface. Improper cooling

may result in premature lamp failure.

Fuse Holder -

This housing stores the 5 amp GMA protective fuse. Always replace

with the exact same type fuse, unless otherwise instructed, by an

authorized American DJ

service technician.

Power Cord -

Connect only to a matching power outlet. Never use this  xture is the

ground prong has been removed or broken off.

Operating Modes:

You may operate your Centurion

™

in three different ways:

•

Stand Alone Mode

- The unit will react to sound, chasing through

the built in programs. You may also use the optional IRC/2 Remote to

control a blackout function.

• Master/Slave Mode

- This mode allows you to daisy chain up to 4

units together to get a synchronized light show that will react to sound

and chase through the several built in programs.

•

DMX Mode

- This function will allow you to control each indi-

vidual fixtures traits with a standard DMX 512 controller such as the

American DJ Show Designer.

™

Note: Stand-Alone and Master-Slave operation require sound to acti-

vate! If the units do not move adjust the volume sensitivity knob on the

rear of the  xture.

Note: To conserve lamp life, the unit will automatically turn off the lamp

when the  xture has been inactive for longer than 60 seconds. This is

not a malfunction and will aid lamp and unit longevity by decreasing

heat.

Stand-Alone Operation (Sound Active):

This function allows a

single unit to run to the beat of the music. Only use this function when

running a single unit, or when running several units as individuals.

To activate the Sound-Active mode refer to

“Master Unit” on the

Master-Slave DIP SWITCH chart on page

3).

The unit will now react to the low frequencies of music via the

internal microphone. The unit is preset to activate at a certain

sound pressure level. Occasionally the unit will not react to certain

high pitch sounds.

The optional

IRC/2 Controller

may be used with this mode to

control stand-by (blackout), gobo change, and to switch between

sound-active and manual modes.

Master-Slave Operation (Sound Active):

This function will allow

you to link up to 4 units together and operate without a controller or with

the IRC/2. The units will react to sound. In Master-Slave operation one

unit will act as the controlling unit and the others will react to the control-

ling units programs. Any unit can act as a Master or as a Slave.

Centurion™ Operation

American DJ

- www.americandj.com - Centurion™ Instruction Manual Page 8

American DJ

- www.americandj.com - Centurion™ Instruction Manual Page 7

Centurion™ Operation

Using standard XLR microphone cables, daisy chain your units

together via the XLR connector on the rear of the units. Remember

the Male XLR connector is the input and the Female XLR connec-

tor is the output. The  rst unit in the chain (master) will use the

female XLR connector only - The last unit in the chain will use the

male XLR connector only. For longer cable runs we suggest a

terminator at the last fixture.

Follow the chart on page 3 for proper unit dip switch settings.

The optional

IRC/2 Controller

may be used with this mode to

control stand-by (blackout), gobo change, and to switch between

sound-active and manual modes.

4. After all the units settings have been set and are plugged in, they

will begin to run to sound. If there is no sound present the units

will blackout to preserve and extended lamp life.

Universal DMX Control:

This function allows you to use a univer-

sal DMX-

512

controller such

as the American DJ

DMX Operator™

or Show Designer.™ to control mirror movement, shutter speed, and

the color/gobo wheel.

Using a DMX controller will allow you to cus-

tomize programs and expand functionality.

Operating through a DMX

controller gives freedom to create unique programs tailored to oneʼs

individual needs.

The Centurion™ uses 3 DMX channels. Channel 1 controls

shutter channel 2 controls the color/gobo wheel, and channel 3

controls the mirror rotation. See page 14 for detailed description of

the DMX traits.

To control your fixture in DMX mode, follow the set-up procedures

on pages 9 - 11 as well as the set-up specifications that are

included with your DMX contro

ller.

Use the controllerʼs faders to control the various DMX fixture traits.

This will allow you to create your own programs.

When using a DMX controller and setting up for DMX operation

follow the dip switch settings on page 14.

For help operating in DMX operation consult the manual included

with your DMX controller.

For

longer cable runs (more than a 100 feet) use a terminator on

the last fixture.

dip switch 10 it is used for special functions such as sound activation.

Each dip switch has a preset value. A specific DMX address is set by

combining the dip switches that sum your desired value. For example:

To achieve a DMX address of 21, combine dip switches 1, 3, and 5.

Sense dip switch 1 has a value of 1, dip switch 3 has a value of 4,

and dip switch 5 has a value of 16, the combination of the create a

DMX value of 21.

Set DMX address 21:

Set DMX address 201:

Dip switch # 1 = 1

Dip switch # 3 = 4

Dip switch # 4 = 8

Dip switch # 5 = 16

Dip switch # 7 = 64

= 21

Dip switch # 8 = 128

= 201

Data Cable (DMX Cable) Requirements (For DMX and Master/

Slave Operation):

The Centurion™ can be controlled via DMX-512

protocol. The American DJ

Centurion™ is a four channel DMX unit. The

DMX address is set on the front panel of the Centurion™. Your unit and

your DMX controller require a standard 3-pin XLR

connector for data input and data output (Figure

1). If you are making your own cables, be sure to

use standard two conductor shielded cable (This

cable may be purchased at almost all pro sound

and lighting stores). Your cables should be made

with a male and female XLR connector on either

end of the cable. Also remember that DMX cable

must be daisy chained and can not be split.

American DJ

- www.americandj.com - Centurion™ Instruction Manual Page 10

American DJ

- www.americandj.com - Centurion™ Instruction Manual Page 9

Power Supply:

Before plugging your unit in, be sure the source volt-

age in your area matches the required voltage for your American DJ

Centurion.™ The American DJ

Centurion

™

is available in a 120v and

220v version. Because line voltage may vary from venue to venue, you

should be sure your unit voltages matches the wall outlet voltage before

attempting to operate you  xture.

DMX-512:

DMX is short for Digital Multiplex. This is a universal

protocol used as a form of communication between intelligent fixtures

and controllers.

A DMX controller sends DMX data instructions from

the controller to the fixture. DMX data is sent as serial data that

travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR

terminals located on all DMX fixtures (most controllers only have a

DATA “OUT” terminal).

DMX Linking:

DMX is a language allowing all makes and models of

different manufactures to be linked together and operate from a single

controller, as long as all  xtures and the controller are DMX compliant.

To ensure proper DMX data transmission, when using several DMX

fixtures try to use the shortest cable path possible. The order in which

fixtures are connected in a DMX line does not influence the DMX

addressing. For example; a fixture assigned a DMX address of 1 may

be placed anywhere in a DMX line, at the beginning, at the end, or

anywhere in the middle. When a fixture is assigned a DMX address of

1, the DMX controller knows to send DATA assigned to address 1 to

that unit, no matter where it is located in the DMX chain.

Dip-switches in DMX mode:

This unit uses dip switches to assign a

DMX address. Each dip switch represents a binary value.

Dip Switch 1 address equals 1

Dip Switch 2 address equals 2

Dip Switch 3 address equals 4

Dip Switch 4 address equals 8

Dip Switch 5 address equals 16

Dip Switch 6 address equals 32

Dip Switch 7 address equals 64

Dip Switch 8 address equals 128

Dip Switch 9 address equals 256

Dip Switch 10 - Some unit omit dip switch 10. When a unit does included

Centurion™ Set Up

128

256

DMX CHANNEL

Figure 1

Centurion™ Set Up

Notice:

Be sure to follow  gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cableʼs shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLRʼs outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

DMX +

DMX -

COMMO

DMX512 OUT

3-PIN XLR

Figure 2

Centurion™ Fuse & Lamp Replacement

American DJ

- www.americandj.com - Centurion™ Instruction Manual Page 11

American DJ

- www.americandj.com - Centurion™ Instruction Manual Page 12

Caution:

Always replace with the exact same type lamp and fuse,

unless otherwise specified by an authorized American

techni-

cian. Replace with anything other than the specified part can damage

your unit and will void your manufactures warranty.

Warning:

If, after replacing the lamp or fuse either one continues

to blow, STOP using the unit. Contact customer support for further

instructions, you may have to return the unit for servicing. Continuing

to use the unit may cause serious damage.

Fuse Replacement:

Disconnect the unitʼs main power supply. Insert

a standard flat head screw driver in to the fuse holder housing. Turn

the screwdriver in counter-clockwise direction to remove the fuse

holder. Remove the fuse holder to expose the fuse. Remove the old

fuse and discard it. Replace the fuse with the same type. Insert the

fuse holder back into itʼs housing and turn it in clockwise direction to

lock the holder in place.

Lamp Replacement:

Caution! Never attempt to change the lamp

while the fixture is plugged in. Always disconnect the main power

and allow the unit ample time to cool before attempting to replace the

lamp. Lamp replacement has been made simple by incorporating the

use of a flip-up front cover that is retained by thumb screws.

Be sure to follow the proper handling procedures that deal with

halogen lamps.

Remove the two thumb screws on the front of the unit.

After removing the thumb screws, pull off socket assembly protec-

tive cover.

Carefully remove the old lamp and discard it in the trash.

Replace the lamp with an exact match and reassemble in reverse order.

Centurion™ Set Up

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number ZDMX/T) will decrease the possibilities of erratic

behavior.

rmination

educes

signal

rrors

and

avoids

signal

transmission

problem

and

interference.

always

advisable

connect

DMX

terminal,

(Resistance

120

Ohm

1/4

between

(DMX-)

and

(DMX

the

last

fixture.

Figure 4

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin XLR

connectors for DATA transmission in place of 3-pin. 5-pin XLR  xtures

may be implemented in a 3-pin XLR DMX line. When inserting standard

5-pin XLR connectors in to a 3-pin line a cable adaptor must be used,

these adaptors are readily available at most electric stores. The chart

below details a proper cable conversion.

Conductor

5-Pin XLR Male (In)

3-Pin XLR Female (Out)

Pin 1

Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

Figure 3

1 Ground

XLR Male Socket

XLR Pin Con guration

3 Hot

2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Halogen Lamp Warning:

This fixture is fitted

with halogen lamps which are highly susceptible

to damage if improperly handled. Never touch the

lamps with your bare fingers as the oil from your

hands will shorten lamp life. Also, never move the

fixture until the lamps have had ample time to cool.

Remember, lamps are not covered under warranty

conditions.

American DJ

- www.americandj.com - Centurion™ Instruction Manual Page 14

Centurion™ Cleaning

Centurion™ Trouble Shooting

Fixture Cleaning:

Due to fog residue, smoke, and dust cleaning the

internal and external optical lenses and mirror should be carried out

periodically to optimize light output. Cleaning frequency depends on

the environment in which the fixture operates (I.e. smoke, fog residue,

dust, dew). In heavy club use we recommend cleaning on a monthly

basis. Periodic cleaning will ensure longevity, and crisp output.

Use normal glass cleaner and a soft cloth to wipe down the outside

casing.

Use a brush to wipe down the cooling vents and fan grill.

Clean the external optics and mirror with glass cleaner and a soft

cloth every 20 days.

Clean the internal optics with glass cleaner and a soft cloth every

30-60 days.

Always be sure to dry all parts completely before plugging the unit

back in.

Trouble Shooting:

Listed below are a few common problems that you

may encounter, with solutions.

No light output from the unit;

Be sure you have connected your unit into a wall outlet with a

matching power supply.

Be sure the external fuse has not blown. The fuse is located on the

rear panel of the unit.

Remove the lamp cover and be sure the lamp is seated in its

socket properly. Occasionally lamps become loose during shipping

be sure the lamp is push in to its socket all the way.

Be sure the fuse holder is completely and properly seated.

Unit does not respond to sound;

Low frequencies (bass) should cause the unit to react to sound.

Tapping on the microphone, quiet or high pitched sounds may not

activate the unit.

American DJ

- www.americandj.com - Centurion™ Instruction Manual Page 13

Centurion™ DMX Traits

The charts below details the DMX traits and the gobo patterns. The

individual trait can only be accessed by an universal DMX controller.

Cha n ne l 1 Cha n ne l 2 Cha n ne l 3DMX

va lu es Shutter Gobo / Color Reflect or M irror

255

246 Stop

245

135

128

Fastest Speed

Slowest Speed Stop

120 Go bo 14 / Green & Pink

112 Go bo 13 / White

104 Go bo 12 / Blue

96 Go bo 11 / Orange

88 Go bo 10 / Magenta

80 Go bo 9 / Pink

72 Go bo 8 / Light Blue

64 Go bo 7 / Magenta

56 Go bo 6 / Red

48 Go bo 5 / Orange

40 Go bo 4 / Green

32 Go bo 3 / Yellow

24 Go bo 2 / Blue

Fast Strobe

Slow Strobe Go bo 1 / Multi-Color

8OPEN

0Stop Blackout Stop

Gobos

Centurion™ DMX Traits

American DJ

- www.americandj.com - Centurion™ Instruction Manual Page 15

X = OFF

O = ON

#1 #2 #3 #4 #5

3 64 96 128 160 192 224 256 288 320 352 384 416 448 480

1 33 65 97 129 161 193 225 257 289 321 353 385 417 449 481

2 34 66 98 130 162 194 226 258 290 322 354 386 418 450 482

3 35 67 99 131 163 195 227 259 291 323 355 387 419 451 483

4 36 68 100 132 164 196 228 260 292 324 356 388 420 452 484

5 37 69 101 133 165 197 229 261 293 325 357 389 421 453 485

6 38 70 102 134 166 198 230 262 294 326 358 390 422 454 486

7 39 71 103 135 167 199 231 263 295 327 359 391 423 455 487

8 40 72 104 136 168 200 232 264 296 328 360 392 424 456 488

9 41 73 105 137 169 201 233 265 297 329 361 393 425 457 489

10 42 74 106 138 170 202 234 266 298 330 362 394 426 458 490

11 43 75 107 139 171 203 235 267 299 331 363 395 427 459 491

12 44 76 108 140 172 204 236 268 300 332 364 396 428 460 492

13 45 77 109 141 173 205 237 269 301 333 365 397 429 461 493

14 46 78 110 142 174 206 238 270 302 334 366 398 430 462 494

15 47 79 111 143 175 207 239 271 303 335 367 399 431 463 495

16 48 80 112 144 176 208 240 272 304 336 368 400 432 464 496

17 49 81 113 145 177 209 241 273 305 337 369 401 433 465 497

18 50 82 114 146 178 210 242 274 306 338 370 402 434 466 498

19 51 83 115 147 179 211 243 275 307 339 371 403 435 467 499

20 52 84 116 148 180 212 244 276 308 340 372 404 436 468 500

21 53 85 117 149 181 213 245 277 309 341 373 405 437 469 501

22 54 86 118 150 182 214 246 278 310 342 374 406 438 470 502

23 55 87 119 151 183 215 247 279 311 343 375 407 439 471 503

24 56 88 120 152 184 216 248 280 312 344 376 408 440 472 504

25 57 89 121 153 185 217 249 281 313 345 377 409 441 473 505

26 58 90 122 154 186 218 250 282 314 346 378 410 442 474 506

27 59 91 123 155 187 219 251 283 315 347 379 411 443 475 507

28 60 92 124 156 188 220 252 284 316 348 380 412 444 476 508

29 61 93 125 157 189 221 253 285 317 349 381 413 445 477 509

30 62 94 126 158 190 222 254 286 318 350 382 414 446 478 510

31 63 95 127 159 191 223 255 287 319 351 383 415 447 479 511

DMX DIP Switch Settings

DIP SWITCHES

OOO OOX OO OXX X X X X X

OOO OOOO OX X XXX X X X

OXO XOO XX OOX X X XOO

XOX XOO OX OXX O X O X O

OXXXX

X O X O X

O X X O X

XXXOX

OOOX X

X O O X X

XXOXX

O O X X X

XOXXX

O X O X X

X OOOX

O O X X O

XOXXO

OXXXO

XXXXO

OOOOX

OX OOX

X X O O X

OOX OX

XXXOO

OOOOO

X OOOO

OX OOO

X X O O O

OOX OO

X O X O O

O X X O O

OOOX O

X O O X O

O X O X O

XXOXO

XXXXX

DMX Address

DMX Address Quick Reference Chart

Dip Switch Position

The center numbers of this chart (1-511) represent a DMX address. The "X"'s

and "O"'s along the top and side of the chart represent dip switch poistion ("X"

for off and "O" for on). Find your desired DMX address from the center chart.

Identify the position for dip switches 1-5 from the chart on the left and dip

switches 6-9 from the chart on the top. Adjust the dip switches on your fixture

to match the position settings of the chart. For fixtures with 10 dip switches;

dip switch 10 is reserved for special functions.

This chart list the DMX dip switch setting for DMX address 1 through

511. Follow the instructions below to configure fixture dip switches with

your desired DMX address.

Centurion™ DMX Dip Switch Chart

A Division of the American DJ® Group of Companies

4295 Charter Street Los Angeles, CA 90058 USA

Tel: 323-582-2650 Fax: 323-582-2610

Web: www.americandj.com E-mail: [email protected]

Technical Specifications:

Model:

Centurion™

Lamps:

LL-EFP, 12v/100w

Voltage:

120v~60Hz / 220v~50/60Hz

Dimensions:

10.3” x 9.5” x 5”

262mm x 240mm x 130mm

Colors

Multiple

Gobos:

14, Plus Spot

Weight:

12.76 Lbs. / 5.8 Kgs

Fuse:

5 Amp GMA

Duty Cycle:

None

DMX:

3 Channels

Sound Active:

Yes

Working Position:

Any Safe, Secure Position

Warranty:

1 Year (365 days)

Please Note:

Speci cations and improvements in the design

of this unit and this manual are subject to change without any

prior written notice.

Inhaltsverzeichnis

Andere American DJ DJ-Equipment Handbücher

American DJ

American DJ 4-Play Bedienungsanleitung

American DJ

American DJ 3.3 Bedienungsanleitung

American DJ

American DJ Nucleus PRO Bedienungsanleitung

American DJ

American DJ Majestic LED Bedienungsanleitung

American DJ

American DJ Torch Light Bedienungsanleitung

American DJ

American DJ Concept Color Bedienungsanleitung

American DJ

American DJ Spiral Graph Bedienungsanleitung

American DJ

American DJ PDP-800 Bedienungsanleitung

American DJ

American DJ Vizi Scan LED PRO Bedienungsanleitung

American DJ

American DJ Flat Par Tri7 Bedienungsanleitung

American DJ

American DJ Pixel Pulse Bar Bedienungsanleitung

American DJ

American DJ Revo I Bedienungsanleitung

American DJ

American DJ HMI 575TM Bedienungsanleitung

American DJ

American DJ Mega Bar LED Bedienungsanleitung

American DJ

American DJ Micro Sky Bedienungsanleitung

American DJ

American DJ Rover 250 Bedienungsanleitung

American DJ

American DJ SWEEPER BEAM QUAD LED Bedienungsanleitung

American DJ

American DJ DJ Roller Bedienungsanleitung

American DJ

American DJ Verti-Pro II Bedienungsanleitung

American DJ

American DJ Utopia 250S Bedienungsanleitung

American DJ

American DJ Mini Tri Ball Bedienungsanleitung

American DJ

American DJ S-10S Bedienungsanleitung

American DJ

American DJ Double Feature Bedienungsanleitung

American DJ

American DJ Crystal Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung