American DJ Rainbow-250 Bedienungsanleitung

American DJ

4295 Charter Street

Los Angeles Ca. 90058

www.americandj.com

User Instructions

Introduction:

Thank you for purchasing the Rainbow 250™ color changer from American DJ®. To optimize the per-

formance of this product, please read these operating instructions carefully and familiarize yourself with

the basic operations of this unit. The American DJ®Rainbow 250,™ is a dual channel, DMX, intelligent

color changer. This unit has been shipped with a lamp installed and tested at the factory before being

shipped to you. There is no assembly required.

The American DJ®Rainbow 250™ has sound active capabilities so you can use this unit without a

controller. This unit can also be controlled via a standard DMX controller such as the American DJ Show

Designer,™ or the American DJ®DMX Operator,™ giving the user independent control over the color

wheel and dimmer.

Customer Support:

American DJ®provides a toll free customer support line, to provide set up and installation help and to

answer any question should you encounter problems during your set up or initial operation. You may

also visit us on the web at www.americandj.com for any comments or suggestions. Toll free customer

service hours are Monday through Friday 9:00 a.m. to 5:00 p.m. Paciﬁc Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2610

E-mail: support@americandj.com

Set Up:

Power Supply:

Before plugging your unit in, be sure the source voltage in your area matches the required voltage for

your American DJ®Rainbow 250.™ The American DJ®Rainbow 250™ is available in a 120v and 220v

version. Because line voltage may vary from venue to venue, you should be sure to plug your power

supply into a matching wall outlet before attempting to operate you controller.

Data Cable (DMX Cable) Requirements:

Your ﬁxture and your controller require a standard 3-pin XLR connector for data

input and data output (Figure 1). If you are making your own cables, be sure to use

standard two conductor shielded cable (This cable may be purchased at almost all

pro sound and lighting stores). Your cables should be made with a male and female

XLR connector on either end of the cable. Also remember that DMX cable must be

daisy chained and can not be “Y”ed or split.

Notice: Be sure to follow ﬁgure three when making your own cables. Do not use the ground lug on

the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a short

circuit and erratic behavior.

1 Ground 1 Ground

XLR Male Socket XLR Pin Conﬁguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Figure 1

Figure 2

Special Note:

When longer runs of cable are used, you may need to use a terminator on the last

unit to avoid erratic behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is connected between

pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR

connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ part

number ZDMX/T) will decrease the possibilities of erratic behavior.

Operation Modes:

For best results use fog or special effects smoke to enhance the beam projections.

Stand-Alone Operation (Sound Active):

1. To operate as a stand alone unit via its internal chases and microphone, turn all dip switches off (See

page 6/ﬁgure 5).

2. Adjust the sensitivity knob on the rear of the unit so the unit will react to sound.

3. Turning the sensitivity knob in the clockwise direction will increase the sensitivity to sound. Turning

the knob in the counter clockwise direction will decrease the ﬁxture’s sensitivity to sound.

4. The American DJ®Rainbow 250™ will now react to the bass sound of music via the internal

microphone.

Master-Slave Operation (Sound Active):

1. This function will allow you to link up to 16 units together. The units will run as a synchronized light

show.

2. In Master-Slave operation one unit will act as the controlling unit and the others will react to the

controlling unit’s program. Any unit can act as a Master or as a Slave.

3. Daisy chain your units via the XLR connectors on the rear of the units.

4. Use standard XLR microphone cables to link your units together. Remember that the Male XLR con-

nector is the input and the Female XLR connector is the output.

5. The ﬁrst unit in the chain (master) will use the female XLR connector only - The last unit in the chain

will use the male XLR connector only.

6. Turn the master unit’s dip switch 10 to the on position. Be sure all other dip switches are set to the

off position (See page 6/ﬁgure 5).

7. Tur n al l di p switches to the off position on the slave units. Please see the chart on page 6 for all slave

dipswitch settings. Note only one ﬁxture may use the master units dip switch settings (See page

6/ﬁgure 5)

8. After all the units’ dip switch settings have been set, plug the units in.

9. Adjust the sensitivity knob on the rear of the master unit to make them react to sound.

DMX512 IN

3-PIN XLR

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 3

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture. Figure 4

DMX Operation:

1. Operating through a DMX controller gives the user freedom to create their own programs tailored to

their own individual needs. This function also allows you to use your ﬁxtures as spots.

2. This operation will allow you to control each ﬁxture’s colors and dimmer with a standard DMX 512

controller such as the American DJ Show Designer™ or the American DJ®DMX Operator.™

3. The American DJ®Rainbow 250™ uses two DMX channel to operate; Channel 1 is the color and

channel 2 is dimmer.

4. To run your ﬁxture in DMX mode, plug in the ﬁxture via the XLR connections to any standard DMX

controller. - Follow the set-up speciﬁcations that come with the controller.

5. Use the chart on page 6 (ﬁgure 4) to set the DMX values for up to 16 units to be controlled by a

DMX controller.

Lens Focusing:

1. To focus a American DJ®Rainbow 250 DMX,™ it is best to ﬁrst turn down the music sensitivity knob

to its minimum position. This will prevent the color wheel from changing during focusing.

2. Adjust the focus by manually turning the lens in and out (clockwise & counter-clockwise), until the

outer edge of the beam is a sharp clear image.

Lamp Replacement:

Caution: Always replace with the exact same type lamp and fuse, unless otherwise specified by an

authorized American DJ®technician. Replace with anything other than the specified part can damage

your unit and will void your manufactures warranty.

Warning: If after you have replaced the lamp or fuse and you continue to blow either one, STOP

using the unit. Contact customer support for further instructions, you may have to return the unit for

servicing. Continuing to use the unit may cause serious damage.

1. Be sure to follow the proper procedures when handling halogen bulbs.

2. Lay the ﬁxture ﬂat on a stable surface.

3. Remove the three Phillips located on the top of the unit.

4. Remove the cover.

5. Remove and replace the bulb.

6. Reassemble.

Cleaning:

Due to fog residue, smoke, and dust, cleaning the internal and external optical lenses must be carried

out periodically to optimize light output.

1. Use normal glass cleaner and a soft cloth to wipe down the outside casing.

2. Use a brush to wipe down the fan grill.

3. Clean the external optics with glass cleaner and a soft cloth every 20 days. If used heavily in clubs

with lots of fog, cleaning may be required more often.

4. Clean the internal optics with glass cleaner and a soft cloth every 30-60 days.

5. Always be sure to dry all parts completely before plugging the unit in.

REMEMBER: Cleaning frequency depends on the environment in which the ﬁxture operates (i.e.

smoke, fog residue, dust, dew).

Warranty: The American DJ®Rainbow 250 DMX™ comes with a one year (365 days) limited war-

ranty. We recommend you fill out the enclosed warranty card to validate your purchase. All returned service items

whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. If

the unit is under warranty, you must provide a copy of your proof of purchase invoice. Please contact American

DJ®customer support for a R.A. number.

DMX Traits:

Channel 1: Channel 2:

DMX Value: Color: DMX Value: Trait:

0-16 Blackout 00 Blackout

17-33 SLOW Strobe 01-254 Dimmer

34-50 White 255 Full Intensity

51-68 Red

69-84 Blue

85-101 Green

102-118 Light Orange

119-135 Dark Orange

136-152 Yellow

153-169 Magenta

170-179 Light Green

180-255 Color Scroll

255 Fastest Color Scroll

Use your controller’s slider to adjust

the DMX value to reach your desired

setting

HALOGEN LAMP WARNING!

This fixture is fitted with halogen lamps

which are highly susceptible to damage

if improperly handled. Never touch lamp

with bare fingers as the oil from your

hands will shorten lamp life. Also, never

move fixture until lamp has had ample

time to cool. Remember, lamps are not

covered under warranty conditions.

SPECIFICATIONS:

Model - Rainbow 250™

Weight: 16 Lbs

Dimensions: 12.75” x 11.75” x 8.5”

Fuse: 4 Amp

Voltage: 120v 60Hz

Bulb: ELC-3 24v/250w Long Life

Duty Cycle: Several Hours

Colors: 8 Colors plus white

• Fan Cooled

• Sound Active

• DMX 512

11098765432

Rainbow 250™ Universal DMX Settings for the ﬁrst 16 ﬁxtures

(If you will not be starting from channel one please follow standard DMX protocol for binary addressing)

Rainbow 250™ Master/Slave Settings - SYNC Mode

Please note: You may connect up to 16 units together in master/slave mode. All off for the master and all slave units will have

dip switch one on). This function will sync all your ﬁxtures together.

Fixture 1 - Address 1

Slave 3 etc...,Slave 2Slave 1Master Unit

Fixture 16 - Address 31Fixture 12 - Address 23Fixture 8 - Address 15Fixture 4 - Address 7

Fixture 15 - Address 29Fixture 11 - Address 21Fixture 7 - Address 13Fixture 3 - Address 5

Fixture 14 - Address 27Fixture 10 - Address 19Fixture 6 - Address 11Fixture 2 - Address 3

Fixture 13 - Address 25Fixture 9 - Address 17Fixture 5 - Address 9

Rainbow 250™ Master/Slave Settings - Chase Mode

For a more dramatic light show you may set-up your ﬁxtures to run in a four-channel chase pattern. This function will run

through a random built in pattern.

11098765432

Slave 3Slave 2Slave 1Master Unit

Inhaltsverzeichnis

Andere American DJ Beleuchtungsausrüstung Handbücher

American DJ

American DJ Emerald Scan II Bedienungsanleitung

American DJ

American DJ Saga II Montageanleitung

American DJ

American DJ Mega Bar LED RC Bedienungsanleitung

American DJ

American DJ Duo Station Bedienungsanleitung

American DJ

American DJ 46HP LED Bedienungsanleitung

American DJ

American DJ Warp Tri LED Bedienungsanleitung

American DJ

American DJ Blade Bedienungsanleitung

American DJ

American DJ Nitro Bedienungsanleitung

American DJ

American DJ DJ SCAN Bedienungsanleitung

American DJ

American DJ P64 LED Plus Bedienungsanleitung

American DJ

American DJ Vizi Spot 5R Bedienungsanleitung

American DJ

American DJ UV Canon Bedienungsanleitung

American DJ

American DJ Accu Color 250 Montageanleitung

American DJ

American DJ Sunray II Bedienungsanleitung

American DJ

American DJ LASER-4800 Bedienungsanleitung

American DJ

American DJ DECO FX Bedienungsanleitung

American DJ

American DJ WiFly Wash Bar Bedienungsanleitung

American DJ

American DJ TRI PEARL LED Bedienungsanleitung

American DJ

American DJ Inno Pocket Spot Pearl Bedienungsanleitung

American DJ

American DJ REVO RAVE Bedienungsanleitung

American DJ

American DJ Color 250D Bedienungsanleitung

American DJ

American DJ MARVEL Bedienungsanleitung

American DJ

American DJ Revo 4 Bedienungsanleitung

American DJ

American DJ Rampage Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung