American Dynamics SpeedDome Ultra Handbuch

SpeedDome®Ultra

Camera Dome

Installation and Service

Manual

8000-1362-01, Rev. B

SpeedDome®Ultra

Camera Dome

Installation and Service Manual

8000-1362-01, Rev. B

MDR 4/97

FCC COMPLIANCE

This equipment has been tested and found to comply with Part 15

of the FCC Rules. Operation is subject to the following two

conditions: 1) this device may not cause harmful interference, and

2) this device must accept any interference received, including

interference that may cause undesired operation.

EQUIPMENT MODIFICATION CAUTION

Equipment changes or modifications not expressly approved by

Sensormatic Electronics Corporation, the party responsible for

FCC compliance, could void the user's authority to operate the

equipment.

WARRANTY DISCLAIMER

Sensormatic Electronics Corporation makes no representation or

warranty with respect to the contents hereof and specifically

disclaims any implied warranties of merchantability or fitness for

any particular purpose. Further, Sensormatic Electronics

Corporation reserves the right to revise this publication and make

changes from time to time in the content hereof without obligation

of Sensormatic Electronics Corporation to notify any person of

such revision or changes.

No part of this manual may be reproduced in any form without

written permission from Sensormatic Electronics Corporation.

SpeedDome is a trademark of Sensormatic Electronics Corpora-

tion. Other product names (if any) mentioned herein may be

trademarks or registered trademarks of other companies.

TABLE OF CONTENTS

TABLE OF CONTENTSTABLE OF CONTENTS

TABLE OF CONTENTS

Preface .........................................................................................................................vi

Chapter 1 INTRODUCTION .................................................................................................... 1-1

PRODUCT OVERVIEW ............................................................................................ 1-2

Main components................................................................................................ 1-2

Camera options................................................................................................... 1-2

Basic geneology.................................................................................................. 1-2

Indoor mounting methods ................................................................................... 1-4

Hard/Tile ceiling mounting ............................................................................ 1-4

Mounting structures (optional) ...................................................................... 1-4

Outdoor mounting method .................................................................................. 1-6

Features ............................................................................................................. 1-6

Performance features................................................................................... 1-6

Video system dependent features ................................................................ 1-7

Installation and service features ................................................................... 1-8

SPECIFICATIONS..................................................................................................... 1-9

Chapter 2 “INDOOR” INSTALLATION................................................................................. 2-1

BEFORE YOU BEGIN............................................................................................... 2-2

Safety .................................................................................................................. 2-2

Verifying equipment and unpacking.................................................................... 2-2

Tools and equipment required ............................................................................ 2-2

Parts check ......................................................................................................... 2-2

I/O board detachment ......................................................................................... 2-2

INSTALLATION PROCEDURE................................................................................. 2-3

How to use this section ....................................................................................... 2-3

Hard/tile ceiling mounting.................................................................................... 2-3

Hard ceiling surface mounting...................................................................... 2-3

Tile ceiling surface mounting........................................................................ 2-4

Optional mounting structures .............................................................................. 2-5

Top hat housing............................................................................................ 2-5

“Fixed” mounting bracket for hard ceilings or 2x2 ceiling tiles...................... 2-6

“Adjustable” mounting bracket for 2x4 ceiling tiles ....................................... 2-8

Wall mounting bracket................................................................................ 2-10

Wall mounting using a corner bracket........................................................ 2-11

Wall mounting using an arm extension ...................................................... 2-12

Wall mounting using a corner bracket and an arm extension .................... 2-13

Hard ceiling pendent mount........................................................................ 2-14

Electrical box attachment ........................................................................... 2-15

Adapter bracket for indoor SpeedDome housings ..................................... 2-16

Dome setup and attachment............................................................................. 2-17

Skirt and bubble attachment ............................................................................. 2-20

Attaching the skirt to the top hat housing ................................................... 2-20

Attaching the bubble to the top hat housing ............................................... 2-20

Attaching the skirt to the indoor SpeedDome housing ............................... 2-21

Attaching the bubble to the indoor SpeedDome housing ........................... 2-21

Attaching the skirt to the indoor SpeedDome housing ............................... 2-22

Chapter 3 “OUTDOOR” INSTALLATION............................................................................. 3-1

BEFORE YOU BEGIN............................................................................................... 3-2

Safety .................................................................................................................. 3-2

Verifying equipment and unpacking.................................................................... 3-2

Tools and equipment required ............................................................................ 3-2

Parts check ......................................................................................................... 3-2

I/O board detachment ......................................................................................... 3-2

INSTALLATION PROCEDURE................................................................................. 3-3

How to use this section ....................................................................................... 3-3

Mounting the dome’s base to the outdoor SpeedDome housing ........................ 3-4

Dome setup and attachment............................................................................... 3-5

Skirt and bubble attachment ............................................................................... 3-8

Chapter 4 SERVICE ................................................................................................................. 4-1

BEFORE YOU BEGIN............................................................................................... 4-2

Tools and equipment required ............................................................................ 4-2

ROUTINE TROUBLESHOOTING ............................................................................. 4-2

Dome functions but does not pan ....................................................................... 4-3

Dome functions but does not tilt.......................................................................... 4-3

Dome does not “home” or respond to commands (dead dome)......................... 4-3

DETAILED TROUBLESHOOTING............................................................................ 4-5

DOME DISASSEMBLY TECHNIQUES..................................................................... 4-5

How to remove the CPU board ........................................................................... 4-6

How to remove the power supply board.............................................................. 4-6

How to remove the pan motor............................................................................. 4-7

How to remove the slot covers............................................................................ 4-7

How to remove the camera................................................................................. 4-8

How to remove the camera/lens board ............................................................... 4-9

How to remove the tilt motor ............................................................................. 4-10

DOME MAINTENANCE........................................................................................... 4-11

Updating/Reprogramming dome software ........................................................ 4-11

Setting the dome address ................................................................................. 4-11

Changing special features ................................................................................ 4-11

Preface

Who should use this manual

Customer Engineers or Dealers who want to install and service

the camera dome.

How this manual is organized

This manual contains the following four sections:

1.0

1.01.0

1.0 INTRODUCTION

INTRODUCTIONINTRODUCTION

INTRODUCTION provides a product overview and

specifications.

2.0

2.02.0

2.0 “INDOOR”

“INDOOR”“INDOOR”

“INDOOR” INSTALLATION

INSTALLATIONINSTALLATION

INSTALLATION provides procedures

required to mount the dome indoors.

3.0

.0.0

.0 “OUTDOOR”

“OUTDOOR”“OUTDOOR”

“OUTDOOR” INSTALLATION

INSTALLATIONINSTALLATION

INSTALLATION provides procedures

required to mount the dome outdoors.

4.0

.0.0

.0 SERVICE

SERVICESERVICE

SERVICE provides troubleshooting and maintenance

information.

Related Documents

Installation and service of this camera dome does not require

detailed knowlege of how it it works or its circuits. However, if

this information is required, order the following document.

Theory for SpeedDome Ultra Camera Domes, document number

8000-1670-01.

Questions?

For technical support on questions that this manual does not

address:

Customer Engineers call: 1-800-543-9740

Dealers call: 1-800-442-2225

CHAPTER 1

SPEEDDOME ULTRA

1-1

SpeedDome Ultra Camera Dome

1INTRODUCTION

nProduct overview ......................................................................1-2

Describes how the dome works, its mounting methods,

major components, and features.

nSpecifications ............................................................................1-9

Lists electrical, environmental, regulatory, and

mechanical specifications for the dome.

INTRODUCTION

SPEEDDOME ULTRA

1-2

PRODUCT OVERVIEW

The SpeedDome Ultra camera dome (Figure 1-1) is part

of a programmable network of camouflaged cameras.

These devices enable security personnel, from a remote

console, to track a target, near or far, even in low light.

Small and unobtrusive, the dome can be used in

facilities such as retail stores, casinos, manufacturing

facilities, hotels, and hospitals, especially where

appearance is important.

Main Components

The dome consists of the following assemblies:

•Base. This assembly mounts directly to an indoor

hard or tile ceiling, or to one of many optional

indoor or outdoor mounting structures. The base has

terminal blocks that receive all video, ac, alarm, and

data connections and has LED indicators that enable

the installer to verify that power and data are

available. The base supplies power and data to the

housing and eyeball assembly, once attached.

•Housing and eyeball assembly. This assembly

“twist locks” onto the base. The housing contains the

dome’s power supply, pan motor, and electronics

used to operate the eyeball. The rotating eyeball,

gloss black and 120mm (4.75") in diameter, contains

a camera, camouflaged lens, tilt motor, and assoc-

iated electronics.

•Camouflaged slot cover (optional). This slot cover

has a 0.5f darker lens that enhances eyeball camou-

flage. It can be used in place of the one on the eye-

ball.

Camera Options

The dome, as shipped, contains one of four different

CCD cameras.

•Color NTSC (60Hz)

•Color PAL (50Hz)

•Monochrome EIA (60Hz)

•Monochrome CCIR (50Hz)

These cameras have 12X optical zoom with continuous

auto focus and backlight compensation. An electronic

zoom provides selectable magnification up to 18X or

48X.

Figure 1-1. SpeedDome Ultra camera dome

Basic Geneology

The dome is available in the four versions listed below.

Basic parts are listed under each version. An exploded

view is shown in Figure 1-2.

•RAS516LP Color NTSC (60Hz)

−0100-1340-01 Base Assy.

−0100-1036-01 Housing and Eyeball Assy.

−0351-1109-01 Install Kit

−0351-1163-01 Slot Cover (optional)

•RAS516LP-1 Color PAL (50Hz)

−0100-1340-01 Base Assy.

−0100-1036-02 Housing and Eyeball Assy.

−0351-1109-01 Install Kit

−0351-1163-01 Slot Cover (optional)

•RAS515LP Monochrome EIA (60Hz)

−0100-1340-01 Base Assy.

−0100-1036-03 Housing and Eyeball Assy.

−0351-1109-01 Install Kit

−0351-1163-01 Slot Cover (optional)

•RAS515LP-1 Monochrome CCIR (50Hz)

−0100-1340-01 Base Assy.

−0100-1036-04 Housing and Eyeball Assy.

−0351-1109-01 Install Kit

−0351-1163-01 Slot Cover (optional)

Base

Housing

and

Eyeball

Assembly

INTRODUCTION

SPEEDDOME ULTRA

1-3

Figure 1-2. Dome components

0400-0833-01 Housing Assy.

0100-1340-01 Base Assy.

Screws (3), M3 x 8 PHP (5801-1051-120)

Slip Ring Assy. (2100-0005-01)

Skirt (0500-6710-01)

Tripod Mount

(0500-6712-01)

Tilt Motor

(3501-0018-01)

Screws, M2x3

(5801-0011-120)

Washer, 1/4 Flat

(2848-8100-07)

0100-1036-00 Housing

and Eyeball Assy.

-01 Color NTSC camera

-02 Color PAL camera

-03 BW EIA camera

-04 BW CCIR camera

0400-0831-00 Eyeball Assy.

-01 Color NTSC camera

-02 Color PAL camera

-03 BW EIA camera

-04 BW CCIR camera

Camera. 1/4 CCD 9Vdc

(2003-0037-01 CLR NTSC)

(2003-0037-02 CLR PAL)

(2003-0037-03 BW EIA)

(2003-0037-04 BW CCIR)

Screw, 1/4-20x3/8

(2802-7407-65)

Bearing Assy., Lens Carriage

(2510-0038-01)

oke Bracket (2)

(0500-7254-01)

Standard Slot Cover with Lens

(0500-6709-01)

(Supplied with Final Assy., not Eyeball Assy.)

0351-1163-01 Install Kit

Optional Slot Cover with 0.5f Darker Lens

(0500-6709-03)

Cable Assy., Tilt

(0650-1680-01)

Slot Cover

(0500-6709-02)

(Supplied with Final Assy., not Eyeball Assy.)

oke

(0500-6709-01)

Camera/Lens Board

(0301-0641-01)

Bearing Assy., Pan Gear

(2510-0040-01)

Housing (0500-7255-01)

Dust Cover

(3100-0066-01)

I/O Board

(0301-0546-01)

Pan Motor (3501-0017-01)

Standoff (3), M3 x 8H x 13L (5899-0055-01)

Screw (4), M3 x 6 (5813-2041-113)

Standoff (3), M3 x 6H x 19L (5887-1122-020)

Power Supply Board (5606-0015-01)

Fan and Cable (0650-1682-01)

Shield (0500-7192-01)

Cap (0500-7256-01)

CPU Board (0301-0578-01)

Ground Clip

(0500-7293-01)

Base

(0500-7257-01)

Andere Handbücher für SpeedDome Ultra

Inhaltsverzeichnis

Andere American Dynamics Sicherheitskamera Handbücher

American Dynamics

American Dynamics SensorRail IIIe ADRL3TRK Series Bedienungsanleitung

American Dynamics

American Dynamics IP speedDome Ultra 8 Bedienungsanleitung

American Dynamics

American Dynamics SpeedDome Ultra VI Montage- und Wartungsanleitung

American Dynamics

American Dynamics RASOPPC-1 Bedienungsanleitung

American Dynamics

American Dynamics ADC520D Bedienungsanleitung

American Dynamics

American Dynamics IP speedDome Ultra 8 Handbuch

American Dynamics

American Dynamics ADCSHR2412N Bedienungsanleitung

American Dynamics

American Dynamics SensorRail IIIe ADRL3TRK Series Bedienungsanleitung

American Dynamics

American Dynamics IP speedDome Ultra 8 Bedienungsanleitung

American Dynamics

American Dynamics ADSDUHOC Bedienungsanleitung

American Dynamics

American Dynamics Illustra 1MP Bedienungsanleitung

American Dynamics

American Dynamics Illustra Flex Series Bedienungsanleitung

American Dynamics

American Dynamics SpeedDome Ultra VIIE Bedienungsanleitung

American Dynamics

American Dynamics IP speedDome Ultra 8 Montage- und Wartungsanleitung

American Dynamics

American Dynamics Tyco ADC770 Bedienungsanleitung

American Dynamics

American Dynamics ADCDW Series Bedienungsanleitung

American Dynamics

American Dynamics ADC521B Bedienungsanleitung

American Dynamics

American Dynamics SpeedDome Optima LT Montage- und Wartungsanleitung

American Dynamics

American Dynamics ADCTDN0230P Bedienungsanleitung

American Dynamics

American Dynamics Illustra Flex Series Bedienungsanleitung

American Dynamics

American Dynamics ADC710 Bedienungsanleitung

American Dynamics

American Dynamics SpeedDome RHODULP-01 Montage- und Wartungsanleitung

American Dynamics

American Dynamics ADC522WP Bedienungsanleitung

American Dynamics

American Dynamics Tyco Discover Series Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung