Ametek HPC50 Series Bedienungsanleitung

HPC50 Series Operation Manual

for the HPC50 Series Intrinsically Safe Handheld Pressure Calibrator

Contents

Overview...............................................................1

Introduction ............................................................1

Quickstart ..............................................................2

Functions ..............................................................3

On/O..................................................................3

Navigation..............................................................3

Settings ................................................................6

Display .................................................................8

Operation..............................................................9

Pressure Sensors ........................................................9

Measuring Current .....................................................13

Sourcing Current.......................................................14

Measuring Voltage .....................................................15

Measuring Temperature (ATMi) .........................................16

Performing a Switch Test ...............................................17

Calibrating a Pressure Transmitter .......................................18

Enclosure .............................................................20

APMi Modules .......................................................21

ATMi Modules .......................................................22

Speciﬁcations .......................................................23

Ranges and Resolutions ................................................28

Safety & Certiﬁcations............................................29

Hazardous Locations ...................................................29

Certications ..........................................................29

Support ...............................................................30

Troubleshooting .......................................................30

Calibration ............................................................31

Accessories and Replacement Parts .....................................32

Warranty ..............................................................33

Overview 1

HPC50 Series Operation Manual

Overview



INTRODUCTION

Thank you for choosing the HPC50 Series intrinsically safe handheld pressure calibrator from Crystal Engineering Corporation. HPC50 calibrators feature dead-

weight tester accuracy in a modern digital package with the safest tting connection available. The full color display features an easy to use interface and may

be used in a broad range of applications from simple tool type jobs to complex calibration jobs in custody transfer systems.

Accuracy is up to 0.035 percent of reading

–

so one HPC50 can typically replace several gauges or calibrators you may have been using. The HPC50 is fully

temperature compensated

–

so there is no change in accuracy throughout the entire operating temperature range!

Single and dual pressure sensor models are available from vacuum up to 15 000 psi / 1000 bar. In addition, the HPC50 features the ability to add up to two

external pressure ports (APMi) to provide up to four pressure ports. When included with a barometric reference (BARO option), all pressure readings can be

displayed as gauge or absolute readings.

In addition to pressure measurement, the HPC50 also includes inputs for mA, voltage, switch testing, and up to two temperature measurement modules (ATMi).

HPC50 Series Measurement Options

Measurement Type Available Modes (as dened on display)

Pressure P1, P2, APMi1, APMi2, Di. Pres, Dual Pres.

Temperature ATMi1, ATMi2

Barometric Pressure BARO

Current mA in

Voltage VDC In

Switch Test Switch Test

Other features include:

•User congurable information display

•% error calculation

•% ow calculation

•Scaling

•Damping

•Leak Testing

•Min/Max hold

•Uses Crystal’s patented CPF ttings and hose system (leak-free and nger-tight to 10 000 psi (700 bar))

We hope your HPC50 meets your expectations, and we’re interested in any comments or suggestions you may have. You can send us a note at:

[email protected]. Many features in this and our other products are a direct result of your comments!

Crystal Engineering is the company that designs, manufactures, and services the nVision reference recorders, XP2i series pressure gauges, 30 series pressure

calibrators, and a variety of industry specic pressure measuring equipment.

Overview 2

HPC50 Series Operation Manual



QUICKSTART

Unique “Non-Menu” User Interface

Easy to use single layer user interface. No deep menu structure!

Operate and set up the HPC50 Series to perform your tasks quickly

and intuitively.

APMi and ATMi Module Connections

Connect 1 or 2 external modules to expand measurement

options. The APMi module for pressure, and the ATMi

module for temperature.

Function Buttons

The function of each

button is clearly explained

on the bottom of the

display.

“Wireless” Keypad

All input and output

connectors are placed

away from the display and

keypad to give maximum

freedom to operate.

Protective Boot

Required for Intrinsic Safety.

Mini-USB Port

Customize the set-up through

free CrystalControl software.

Color Display

The large, full-color,

sunproof display

combined with the

advanced simplicity of

the user interface, makes

the HPC50 Series the

easiest-to-use pressure

calibrator available.

Cursor Keys

Cursor keys help you to

navigate through the

display to perform set up

functions and ne tune

values.

CPF Pressure Connections

Includes patented, leak-free, nger-tight

CPF connection ttings.

Functions 3

HPC50 Series Operation Manual

Functions



ON/OFF

Power button

Press and hold the (power)button to turn the HPC50 Series on or o.

The HPC50 will automatically power down if not used for the time period dened in the unit settings or in CrystalControl.

Automatic Shuto - Low Power Mode

To optimize battery life, adjust your Automatic Shuto time (shut o time in absence of key press) on the unit or through the free

CrystalControl software. This feature is adjustable from 5 minutes to“always on.”



NAVIGATION

Arrow Buttons

The (arrow)buttons serve dierent functions depending on the mode of operation. Press any of the four (arrow)buttons to enter

“Navigation Mode”. In this mode, the user can scroll through editable elds directly onscreen.

Navigation Mode: Use the four (arrow)buttons to move the cursor in the desired direction.

Edit Mode: Use the Up and Down (arrow)buttons to scroll through lists of options. Or, if entering a number, use the left and right

(arrow)buttons to move the cursor one character in the desired direction.

Back Button

Press the (back)button to cancel a selection or to return to a previous menu.

Enter Button

Press the (enter)button to view/accept selected options or entered values. When a value is entered with the (enter)button, the cursor selects

the next value eld in the list.

Functions 4

HPC50 Series Operation Manual

Zero Button

zero

Press the (zero)button to activate the function key options. The HPC50 will display the parameters that are currently shown on the upper and

lower displays. Press the (function)button for the parameter that you would like to zero. The display will then briey ash all dashed lines

(-----), indicating that it has been zeroed.

Note: If you attempt to zero the gauge with more pressure applied than the Zero Limit set on the HPC50 (or with CrystalControl) the command will be

ignored, and Over Zero Limit will display.

Note: The BARO sensor cannot be zeroed.

! WARNING: This calibrator can display zero pressure when connected to a source of pressure! Do not rely on the display indication before disconnecting—

it may not be indicating true pressure. Never disconnect pressure instrumentation without rst relieving system pressure!

XTo Clear the Zero Value

1 Press the (zero)button to activate the (function)buttons for the available pressure sensors.

2 Press and hold the (function)button for the sensor that you would like to unzero until the display changes from (- - - - -) to (- - -).

XTo Clear the Peaks

1 Press the (zero)button to activate the (function)buttons for the available pressure sensors.

2 Press the (function)button for Peaks to reset the P1, P2, and APMi peaks.

Navigating Through a Typical Setup

1 Press any of the (arrow)buttons to enter Navigation Mode.

2 Use the (arrow)buttons to move between the congurable elds within the upper and lower displays.

Note: Congurable elds are not highlighted in light blue on the actual display; but selected elds are highlighted in dark blue.

3 Use the (enter)button to select a eld for editing.

Functions 5

HPC50 Series Operation Manual

4 Use the up and down (arrow)buttons to select a new value, then press the (enter)button to choose the new value.

Select a Value… then press enter.

Note: To exit Navigation mode without making a selection, press the (back)button.

Calibration Due Reminder

The HPC50 Series has a calibration reminder feature that can help to assure that you never use the calibrator after its calibration certicate has expired. Set

calibration due dates and warning period through our free CrystalControl software.

XCalibration Reminder Alert

Enter the Cal Due date and the warning period prior. Once the dened time prior is reached, the HPC50 will ash Cal Soon during the startup process. It will

do this on every start-up until the calibration due date is reached, or the dates are updated.

XCalibration Due Alert

Once the calibration due date has been reached, the HPC50 will ash Cal Due during start-up. While in use, the HPC50 display will alternate displaying Cal Due

and live pressure readings. This behavior will continue until the calibration date is updated through CrystalControl.

Functions 6

HPC50 Series Operation Manual



SETTINGS

Settings Button

Press the (settings)button to enter the system settings menu.

XRecall

Used to recall a saved setup.

XSave

Used to store the current display setup. Saving a setup allows for quick loading of the same congurations for later use. This makes it easy to switch between

dierent applications or tasks. Up to 5 setups can be stored.

XGeneral

Used to view or edit the following system settings:

• Auto O Time

• HART resistor On/O

• Serial Number

• Firmware Version

• Part Number

XP1, P2, and APMi

• Mode: Switch between absolute and gauge pressure

• Filter Time

• Zero Limit

• Maximum Resolution: When a resolution less than standard is selected, the displayed number will include an asterisk (*)

• Overpressure Count: Counts the times when pressure has exceeded 110% of the range

• View Calibration Details

• Serial Number

• Part Number

Functions 7

HPC50 Series Operation Manual

XBARO

• Maximum Resolution: When a resolution less than standard is selected, the displayed number will include an asterisk (*)

• View Calibration Details

• Serial Number

• Part Number

XATM i

• Maximum Resolution: When a resolution less than standard is selected, the displayed number will include an asterisk (*)

• Probe Coecients: Enter and modify RTD coecients

• View Calibration Details

• Serial Number

XmA In, mA Out (sink) and VDC In

• Maximum Resolution: When a resolution less than standard is selected, the displayed number will include an asterisk (*)

• View Calibration Details

• Serial Number

XTo Save a Setup

After you have congured the unit, you can save the setup for future use.

1 Press the (settings)button to enter the settings section.

2 Press the (arrow)buttons to highlight the Save Setting, and the press the (enter)button.

3 Press the (arrow)buttons to highlight the setup you want to modify, and then press the (enter)button.

4 Use the (arrow)buttons to change the name of the saved setup. When nished press the (enter)button.

The name is limited to eight characters.

Highlight the settings to modify... then change the name of the saved setup.

5 Press the (F3)function button for Save.

Functions 8

HPC50 Series Operation Manual

XTo Recall a Setup

1 Press the (settings)button to enter the settings section.

2 Press the (arrow)buttons to highlight the Recall Setting, and then press the (enter)button.

3 Press the (arrow)buttons to highlight the setup you want to use, and then press the (enter)button.

The name of the setup will appear in the upper-left corner

Highlight the setup… then press enter.



DISPLAY

The display is divided into two sections: the upper and lower displays. The upper display can be congured to show values for Current, Voltage, Temperature,

Pressure, BARO, or Switch Test. The lower display can be congured to show values for only Temperature, Pressure, and BARO.

Upper Display (showing Current)

Lower Display (showing Pressure)

Inhaltsverzeichnis

Andere Ametek Prüfgeräte Handbücher

Ametek

Ametek Surtronic Duo Bedienungsanleitung

Ametek

Ametek JOFRA ASC300 Bedienungsanleitung

Ametek

Ametek JOFRA RTC-156 A Bedienungsanleitung

Ametek

Ametek TAYLOR HOBSON Surtronic S-100 Series Bedienungsanleitung

Ametek

Ametek Mocon Dansensor LeakPointer 3 Bedienungsanleitung

Ametek

Ametek Jofra MTC-650 A MKII Bedienungsanleitung

Ametek

Ametek VERSITRON BT130S Bedienungsanleitung

Ametek

Ametek NSG 4070C Bedienungsanleitung

Ametek

Ametek JOFRA CSC200 Bedienungsanleitung

Ametek

Ametek WT Series Bedienungsanleitung

Ametek

Ametek JOFRA STS-050 A/B Bedienungsanleitung

Ametek

Ametek JOFRA AMC910 Bedienungsanleitung

Ametek

Ametek Crystal Pressure XP2i-DD Bedienungsanleitung

Ametek

Ametek Chatillon CS1100 Bedienungsanleitung

Ametek

Ametek NSG 4070C1 Bedienungsanleitung

Ametek

Ametek JOFRA IPI Leitfaden

Ametek

Ametek Newage USB Lab B.O.S.S. Bedienungsanleitung

Ametek

Ametek Crystal Pressure M1 Bedienungsanleitung

Ametek

Ametek T Series Bedienungsanleitung

Ametek

Ametek Teseq NSG 3060 Bedienungsanleitung

Ametek

Ametek Crystal Pressure HPC40 Series Bedienungsanleitung

Ametek

Ametek PCD 8 b Series Bedienungsanleitung

Ametek

Ametek CSC201 Bedienungsanleitung

Ametek

Ametek JofraCloud 3G Gateway Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung