AMG Systems AMG5413A9 Bedienungsanleitung

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page 1 of 12 AMG5413A9 Instruction Sheet

D20762-00.doc

AMG5413A9

Instruction Manual

Transmit Unit with one Bi-directional Data Channel, one Bi-

directional Alarm and one Bi-directional Audio Channel for

a Multimode Fibre Link

The AMG5413A9 is a standalone transmit unit designed to transmit & receive one Bi-directional alarm,

one Bi-directional audio channel and one Bi-directional data signal over a Multimode optical fibre.

The AMG5413A9 is designed to be powered using an AMG2001 standalone power supply.

The AMG5413A9 is designed to operate with an AMG5414A9 / AMG5414A9R receive unit in a point

to point configuration. The R suffix in the partno. indicates a rackmount configuration.

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page 2 of 12 AMG5413A9 Instruction Sheet

D20762-00.doc

Contents

Introduction 3

Unit Functional Schematic .................................................................................................................. 3

Optical Connection ............................................................................................................................. 3

Connections 4

Optical Connections Multimode .......................................................................................................... 4

Power Connection .............................................................................................................................. 4

Data and Alarm Channel Connections ............................................................................................... 4

Audio Connections ............................................................................................................................. 4

Front Panel Indicators 6

Power / Opto LED ............................................................................................................................... 6

Low Speed Data LEDs ....................................................................................................................... 6

Alarm LEDs......................................................................................................................................... 6

Audio LEDs ......................................................................................................................................... 6

Data and Alarm Channel Configuration 7

Data Channel Configuration ............................................................................................................... 7

Data Interface Connections ................................................................................................................ 8

Alarm Channel Configuration ............................................................................................................. 8

Alarm Interface Connections .............................................................................................................. 8

Audio Channel Configuration .............................................................................................................. 9

Audio Interface Connections .............................................................................................................. 9

Physical Information 10

Dimensions ....................................................................................................................................... 10

Mounting Details ............................................................................................................................... 10

Safety 10

Maintenance and Repair 10

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page 3 of 12 AMG5413A9 Instruction Sheet

D20762-00.doc

Introduction

Unit Functional Schematic

The

AMG5413A9

transmits 1 data, 1 Bi-

directional alarm and 1 audio signal to the

AMG5414A9 receive unit.

It also receives 1 data, 1 Bi-directional

alarm and 1 audio signal transmitted from

the AMG5414A9.

Optical Connection

The AMG5413A9 connections are illustrated in the following example which shows an AMG5413A9

transmit unit together with an AMG5414A9 standalone receive unit configured as a single channel

point to point system.

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page 4 of 12 AMG5413A9 Instruction Sheet

D20762-00.doc

Connections

Optical Connections Multimode

No. of Optical Connections .................. 1

Optical Fibre ........................................ Multimode 50/125 or 62.5/125**

Connector ............................................ SC/PC

Minimum Optical Launch Power .......... -10dBm

Transmit Wavelength ........................... 1310nm

Minimum Optical Sensitivity ................. -30dBm

Receive Wavelength ............................ 1510nm

Minimum Optical Dynamic Range ....... 20dB.

**Note: the transmission distance is limited by the bandwidth of the Multimode optical fibre. The optical

data rate is 155Mbits/s, which may restrict operation to a maximum fibre length of 7km, although in

most cases the units will operate successfully over longer fibre lengths. It is advisable however for

distances greater than 7km, to have the optical fibre tested.

Power Connection

Connector Type ................................... Removable 2-pin, 3.81mm, Screw Terminal

Connector Partno. ................................ Phoenix 1803578

Supply Voltage ..................................... +12 to +15 Volts DC

Maximum Power .................................. 3.0 Watts

Data and Alarm Channel Connections

No. of Data Channels .......................... 1

No. of Alarms ...................................... 1

Connectors .......................................... Removable 8-pin, 2.5mm, Screw Terminal

Connector Partno. ................................ Phoenix 1881383

Data Interfaces .................................... RS-232, RS-422 or R-S485. Selected by slide switch inside

enclosure. *See appropriate section on how to remove the case

for access to the data switches

RS-485 – Switch Position - Top

RS-422 – Switch Position - Middle

RS-232 – Switch Position - Bottom

Alarm Input .......................................... Contact Closure pull-up is 330R to +3V3

Alarm Output ........................................ Solid-state Relay, maximum 150mA at 125Vac/dc, Ron < 6.5Ω

Audio Connections

No. of Audio Channels ......................... 1

Connectors .......................................... Removable 5-pin, 2.5mm, Spring Terminal

Connector Partno. ................................ Phoenix 1881354

Input level ............................................ 0dBm

Input overload level .............................. +6dBm

Input impedance .................................. 10kΩ / 600Ω

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page 5 of 12 AMG5413A9 Instruction Sheet

D20762-00.doc

Output impedance ............................... 600Ω

Frequency response ........................... 10Hz to 20KHz

Audio Input impedance is selected by removable jumper JP1 or JP2 on Audio Expansion board inside

enclosure. *See appropriate section on how to remove the case for access to the data/audio switches.

1-2 – High Impedance 10kΩ

2-3 – Balanced 600Ω

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page 6 of 12 AMG5413A9 Instruction Sheet

D20762-00.doc

Front Panel Indicators

Power / Opto LED

Power / Opto ........................................ Green - Unit powered, Opto sync.

Red - Unit powered, no Opto sync.

Off - No power applied to unit

Low Speed Data LEDs

Data Present IN (RS485 or RS422) .... Green - logic zero (+V, -V) present on IN+, IN-

Red - logic one (-V,V+) present on IN+, IN-

Off - tri-state off or no connection on IN+, IN-

Data Present IN (RS232) ..................... Green - logic zero (+V) present on input IN+

Red - logic transitions present on input IN+

Off - logic one (-V) present on input IN+

IN corresponds to the data signals being transmitted onto the optical fibre.

Data Present OUT (RS485 or RS422) Green - logic zero (+V,-V) present on OUT+, OUT-

Red - logic one (-V,+V) present on OUT+, OUT-

Off - tri-state off or no connection on OUT+, OUT-

Data Present OUT (RS232) ................. Green - logic zero (+V) present on OUT+

Red - logic transitions present on OUT+

Off - logic one (-V) present on OUT+

OUT corresponds to the data signals being received from the optical fibre.

Alarm LEDs

ALARM IN ............................................ Green - Alarm ON / Contacts closed.

Off - Alarm OFF / Contacts open.

ALARM OUT ........................................ Green - Alarm ON / Contacts closed.

Off - Alarm OFF / Contacts open.

Audio LEDs

Audio Present TX ................................. Green - audio present > -40dBm

Red - audio present > 0dBm (overload at +6dBm)

Off - audio not present or < -40dBm

This represents the audio signals being transmitted on the optical fibre

Audio Present RX ................................ Green - audio present > -40dBm

Red - audio present > 0dBm (overload at +6dBm)

Off - audio not present or < -40dBm

This represents the audio signals being received from the optical fibre.

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page 7 of 12 AMG5413A9 Instruction Sheet

D20762-00.doc

Data and Alarm Channel Configuration

The AMG5413A9 transmit unit sends and receives data to/from an AMG5414A9 or rackmount

equivalent AMG5414A9R receive unit. The physical data interface RS-485, RS-422 or RS-232 is

selectable by the user with the slide switch mounted on the main PCB inside the enclosure.

One bi-directional alarm is also provided. The alarm input is typically connected to a contact closure

switch. The alarm output can receive an on/off signal from an AMG5414A9 and is typically used to

convey contact closure status.

Data Channel Configuration

Each low speed data channel provides an RS-232, RS-422 (full duplex, four wire) or RS-485 (half

duplex, two wire) interface defined by the corresponding mode switch inside the enclosure. Every data

channel as shipped from the factory is set up for RS-485 operation unless otherwise requested.

The data input for both the RS-485 and the RS-422 modes detects a tri-state input condition by

monitoring the differential voltage level across the input. A differential level below 600mV positive or

negative will be detected as a tri-state condition. A level above 600mV positive or negative will be

detected as a logic 1 or logic 0 respectively. It is important therefore to terminate the RS-485 bus or

the RS-422 input bus using 120Ω if a pre-bias is present on the RS-485 or RS-422 bus.

A large number of third party equipment manufacturers apply a pre-bias on their RS-485 bus. This pre-

bias is applied by pulling one arm of the RS-485 bus high (+5 volts) and the other arm low (0 volts)

using high value resistors within the third party equipment. In order to ensure that the AMG equipment

detects a tri-state condition, then these resistors should have a value above 5kΩ. If the third party

bias resistors are less the 750Ω the bus can be multiple terminated as required to ensure that a tri-

state level is detected.

The system detects a tri-state input condition on the data channel bus when in RS-485 or RS-422

mode.

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page 8 of 12 AMG5413A9 Instruction Sheet

D20762-00.doc

Data Interface Connections

Connector

Pin No.

Data Channel

RS-485

[switch top]

RS-422

[switch middle]

RS-232

[switch bottom]

IN + (A) IN

IN - (B)

GND GND GND

IN/OUT + (A) OUT + (A)

IN/OUT - (B) OUT - (B) OUT

Note: (A) or (B) in brackets in the above table refers to RS-485 / RS-422 data specification.

Alarm Channel Configuration

The AMG5413A9 provides 1 Bi-directional alarm output / contact closure input.

The alarm input is typically connected to a contact closure switch. An ALARM IN+ input incorporates a

330R pull-up resistor to the internal +3V3 supply.

The alarm output can receive an on/off signal from an AMG5414A9 and is typically used to convey

contact closure status. An alarm output uses a solid-state relay, with a maximum load current of

150mA at 125Vac/dc and Ron < 6.5Ω.

Alarm Interface Connections

Connector

Pin No.

Alarm Interface

Alarm IN

Alarm OUT

GND

ALARM IN +

ALARM OUT -

ALARM OUT +

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page 9 of 12 AMG5413A9 Instruction Sheet

D20762-00.doc

Audio Channel Configuration

The AMG5413A9 provides one bi-directional audio channel.

The audio channel input can be configured as a single-ended high impedance 10kΩ input with GND

reference or alternativly as a balanced 600Ω input pair. The input impedance is selected using

jumpers on the audio expansion board JP1 (Channel 1) or JP2 (Channel 2), the default setting is

balanced 600Ω.

JP1/JP2 1-2 – High Impedance 10kΩ

JP1/JP2 2-3 – Balanced 600Ω

Audio Interface Connections

Connector Pin

No.

Balanced Input

600Ω

High Z input 10kΩ

OUT - OUT -

OUT + OUT +

GND GND

IN + IN

IN - GND

AMG Systems Ltd. reserves the right to make changes to this

document without notice. The information herein is believed to

be accurate. No responsibility is assumed by AMG for its use.

Page 10 of 12 AMG5413A9 Instruction Sheet

D20762-00.doc

Physical Information

Dimensions

Height................................................... 112mm

Width .................................................... 170mm (excluding connectors)

Depth ................................................... 35mm

Weight .................................................. 600grams

Mounting Details

The AMG unit is supplied with a clip-on mounting bracket which should be attached to a panel or wall

using 2 off 4.0mm screws, see diagram on page 1 for dimensions. The unit is clipped into the

mounting bracket, and is then held firmly in position.

Safety

AMG Optical Fibre Products use Class 1 laser systems in accordance with EN 60825-2:2000.

It is always advisable to follow good practice when working with optical fibre systems. This includes:

 Do not stare with unprotected eyes or with any unapproved collimating device at fibre

ends or connector faces, or point them at other people.

 Use only approved filtered or attenuating viewing aids

For other safety issues and advice on good practice associated with optical fibre systems, please see

EN 60825-2:2000 or your local safety officer.

Maintenance and Repair

There are no user serviceable parts within AMG products. See unit data sheet for full specification.

In case of problem or failure, please call your local support centre or contact: AMG Systems Ltd. at

3 The Omega Centre, Stratton Business Park, Biggleswade, Beds., SG18 8QB, UK.

Phone +44 (0) 1767 600 777

Technical Support +44 (0) 1767 604 491

Email techsupport@amgsystems.com

Inhaltsverzeichnis

Andere AMG Systems Netzwerkzubehör Handbücher

AMG Systems

AMG Systems AMG5414-HS Bedienungsanleitung

AMG Systems

AMG Systems AMG5904A966G Bedienungsanleitung

AMG Systems

AMG Systems AMG2743-SF Bedienungsanleitung

AMG Systems

AMG Systems AMG2747-SF Bedienungsanleitung

AMG Systems

AMG Systems AMG5424R Bedienungsanleitung

AMG Systems

AMG Systems AMG2783-2 Bedienungsanleitung

AMG Systems

AMG Systems AMG2783A-1-DR-CWDMnm-SF Bedienungsanleitung

AMG Systems

AMG Systems AMG5414R Bedienungsanleitung

AMG Systems

AMG Systems AMG5904-2A9R Bedienungsanleitung

AMG Systems

AMG Systems AMG2783R-DR Bedienungsanleitung

AMG Systems

AMG Systems AMG2783R-1-DR-SF Bedienungsanleitung

AMG Systems

AMG Systems AMG2783R-DR-SF Bedienungsanleitung

Beliebte Netzwerkzubehör Handbücher anderer Marken

Valcom

Valcom VIP-804 Bedienungsanleitung

SKUTCH

SKUTCH BA-1000 Produkthandbuch

QUNDIS

QUNDIS RNN5 Bedienungsanleitung

Asus

Asus AAEON FWS-2365 Bedienungsanleitung

Sophos

Sophos XG 85w Bedienungsanleitung

AMCI

AMCI RBE2-8 Bedienungsanleitung

Patton electronics

Patton electronics 2888 Bedienungsanleitung

Cradlepoint

Cradlepoint COR IBR1100/IBR1150 Bedienungsanleitung

Paradyne

Paradyne Hotwire 8620 Bedienungsanleitung

Infra Cool

Infra Cool F-1.3 Bedienungsanleitung

Edgewater Networks

Edgewater Networks 4300T Bedienungsanleitung

Edimax

Edimax SB-2200g Bedienungsanleitung

Extreme Networks

Extreme Networks Mogul-100 Bedienungsanleitung

Aaeon

Aaeon FWS-8500 Bedienungsanleitung

Panduit

Panduit Z11C Series Bedienungsanleitung

F5 BIG-IP 10000 Series Montageanleitung

ZyXEL Communications

ZyXEL Communications NMA1115 Bedienungsanleitung

Auerswald

Auerswald COMtrexx Business Bedienungsanleitung