AMI Musik DS5 Bedienungsanleitung

MUSIK DS5

DAC I Headphone Amp I DSD 64/128

Owner’s manual

AMI International, Inc.

* The WEEE marking on the product indicates this product must not be disposed of with user's other household waste and must be handed over to a des-

ignated collection point for the recycling of waste electrical and electronic equipment!

* The WEEE marking applies only in European Union's member states.

trieval system, or translated into any language or computer language, and any form or by any means, electronic, mechanical, magnetic, optical, chemical,

manual or otherwise, without the prior written permission from AMI International, Inc. In no event will AMI International, Inc. be liable for direct, indirect,

special, exemplary, incidental, or consequential damages resulting from any defect or omission in this manual, even if advised of the possibility of such

damages. In the interest of continued product development, AMI International, Inc. reserves the right to make improvements to this manual and the

products it describes at any time, without notices or obligation.

Disclaimer

The software described in this document is furnished under a license agreement and may be used or copied only in accordance with the terms of the

license agreement. It is against the law to copy the software on any other medium except as specifically allowed in the license agreement. The licensee

may make one copy of the software for backup purposes only. The Software License Agreement is found in a separate folder on the Installation and Ap-

plications CD. In the interest of continued product development, AMI International, Inc. reserves the right to make improvements to this manual and the

products it describes at any time, without notices or obligation.

Trademarks

AMI, AMI International, Inc. logos are trademarks of AMI International, Inc. All other trademarks, logos are trademarks or registered trademarks of their

respective owners.

Safety notification

To reduce the risk of electrical shocks, fire, and related hazards:

・We recommend to not removing screws, cover, or aluminum case. Refer servicing to qualified service personnel.

・Do not expose this device to rain, moisture or spillover of liquid of any kind.

・Should any form of liquid or a foreign object enter the device, do not use it. Switch off the device and then unplug it from the power source. Do not

operate the device again until the foreign object is removed or the liquid has completely dried and its residues fully cleaned up. If in doubt, please

consult the manufacturer.

・Do not handle the power cables with wet hands!

・Make sure the device is switched off when plugging/unplugging it to/from the power source.

・If anything goes wrong, turn off the device first and then unplug the power. Do not attempt to repair the device yourself: consult authorized service per-

sonnel or your dealer.

・Do not install near any heat sources such as radiators, stoves, or other apparatus (including amplifiers) that produce heat.

AMI MUSIK DS5

AMI MUSIK DS5 Owner’s manual

・Do not use harsh chemicals to clean your Unit. Clean only with spe-

cialized cleaners for electronics equipment.

・The AMI MUSIK DS5 comes with surge protection and voltage pro-

tection function against external electrical shock or overvoltage input.

The AMI MUSIK DS5 will be automatically stopped to protect the

product and avoid internal circuit damage. This is a normal behavior

of the AMI MUSIK DS5.

1. Package Con en s

Please make sure you have all of the following contents:

(1) AMI MUSIK DS5 x 1

(2) 5V 3A AC-DC Adaptor x 1

(3) USB A male - USB B male cable x 1

(4) Bumpon x 4

(5) Quick start guide x 1

(6) Driver Installation CD-ROM x 1

Other connecting cables are not included.

2. Sys em requiremen

(1) Operating system

• WDM Kernel Streaming, WASAPI, Direct Sound Dedicated drivers

for:

Microsoft Windows® XP incl. SP3

Microsoft Windows® Vista (32/64bit incl. SP2)

Microsoft Windows® 7 (32/64bit)

Microsoft Windows® 8 (32/64bit)

No driver needed for Apple Mac OS X (10.6 or later)

No driver needed for Linux with UAC2 compliant kernel (2.6.37 or

later)

(2) Suggested system requirement

• Genuine Intel® Pentium® IV 2GHz, AMD® equivalent processor

or faster (Microsoft Windows XP)

• Genuine Intel® Pentium® IV 2.4GHz, AMD® equivalent processor

or faster (Microsoft Windows Vista / Windows 7 & 8)

• Intel, AMD or 100% compatible motherboard chipset

• 1GB RAM (Windows XP) / 2GB RAM (Windows Vista / Windows

7 & 8)

• 10GB of free hard disk space

• USB type A female USB 2.0 hi-speed port

3. Produc fea ures & Componen s

• DSD DAC and headphone amp supporting 2.8MHz (DSD64)/5.6MHz

(DSD128)

• Standalone DAC support (with coaxial and optical input)

• Asynchronous USB operation: bit-perfect digital audio and low clock

jitter.

• USB audio class 2 (up to 24bit/192kHz) and high-speed asynchro-

nous mode: Microsoft Windows® XP, Windows® Vista and Win-

dows® 7 (32bit/64bit) with special driver compatible with

WDM/Direct X, ASIO 2.1 and WASAPI exclusive. Apple OSX ver-

sion 10.6.4 and above & Linux Kernel 2.6.37 and above (no driver

install required).

• Atmel SAM3 Cortex™-M3 microcontroller to support up to

32bit/384kHz, DSD64/DSD128 audio data (support up to 192kHz

with CS4398)

• Customized AMANERO Technologies COMBO384 USB 2.0 Audio

Class solution supporting PCM 24bit/192kHz and DSD64/DSD128.

This solution provides Mute/DSD out enable pin allowing to safely

shifting between PCM and DSD.

• AMANERO firmware update manager allows updating possible fu-

ture firmware via online.

• Cirrus Logic CS4398 (120dB, 192kHz multibit DAC) 120dB dynamic

range, advanced segment DAC architecture supporting

DSD64/DSD128 format and automatic mute algorithm.

• Wolfson WM8804 S/PDI transceiver supporting advanced jitter

attenuating PLL with low intrinsic period jitter of 50ps RMS provid-

ing even best audio playback experience from external signal input.

• TI TPA6130A2 Stereo headphone amplifier for superior PCM and

DSD signal playback via headphone (Max 16 Ω138mW)

• Over voltage protection logic. In case of AMI MUSIK DS5 reaches

5.5V, the protection logic would activate to protect the DAC, and

various IC.

• 2 W 1:1 input range, dual unregulated output, 1000 Vdc isolation,

DC-DC converter

High-efficiency analog power supply circuitry for supporting sec-

ondary rectification by linear regulator for isolating +/- 12V unreg-

ulated power generated from the +5V external power thoroughly

blocking external intervention from analog power and providing

clean, low energy, low heat DC power

• Dual line output mode support pure DAC mode (fixed gain) and pre-

amp mode (variable gain, digital volume control)

• 20PPR mechanical encoders Quadrature 20-step encoder allowing

control of on/off power, volume control, D U mode in/output.

• ade in/out featured for switching mode and playback for your hear-

ing protection.

• 7T/5T aluminum front/top for anti-vibration

AMI International, Inc.

• LED for sample rate, input and output status, volume level and dif-

ferent settings indication.

5. Produc appearances and func ions

(1) Front panel

①Volume knob & Power button

• On/off power button: Push the volume knob for approximately 1

second for power on/off

• Volume control: Turn the volume knob for controlling the volume

(up to 56 levels)

• When turning the volume knob, the LED will instantly show the vol-

ume level (approximately 7 levels are represented by 1 LED)

• When in fixed mode, the line out volume is set to “fixed”. The vol-

ume knob would not control the volume of the line out, but would

continue to control the volume of the headphone out.

②Input (default: USB)

• Push button to select input source (USB – Coaxial – Optical)

※The default input is set to USB

③Output (default: Line)

• Push button to select output source (RCA Line out – Headphone

out)

※The default output is set to Headphone out

④Headphone output

• Push Output button to select headphone out mode

※The line output sound is automatically muted.

⑤LED

• Sample rate indicator

• Input/output indicator

• Volume indicator

• Different setting indicator (fixed/variable mode, etc…)

(2) Rear panel

⑥Line output : Standard dual RCA stereo line output jack support pure

DAC mode (fixed gain) and preamp mode (variable gain).

⑦Coaxial input: Support up to 24bit/192kHz coaxial RCA S/PDI input

(Standalone DAC support)

⑧Optical input : Support up to 24bit/192kHz TOSLINK S/PDI input

(Standalone DAC support)

⑨USB input : Support up to 24bit/192kHz and high-speed asynchro-

nous mode USB input

⑩DC input : DC 5V 3A adopter input

⑪Ground : Connect ground cable in case you need grounding.

A I USIK DS5 supports dual line output mode.

(1) Preamp mode-Variable mode (default): Volume control is

possible via the volume knob for Line out and Headphone out.

The last volume level is remembered when restarting in vari-

able mode.

(2) DAC mode-Fixed mode: Line out volume is set to “fixed”.

The volume knob will not be able to control the line out volume

level (except for the headphone out volume level). The volume

level will be reset to 20% to protect your ear protection.

※Fixed/variable mode setting

1) Turn off the device by pushing the volume knob

2) Push the in/out button simultaneously.

• 44.1 LED blinking: ixed mode

• 48 LED blinking: Variable mode

3) Turn on the device by pushing the volume knob.

AMI MUSIK DS5 Owner’s manual

6. Driver ins alla ion & sys em se up

[Notice] Some music players does not support native playback of music

files. We would like to recommend you to install music players that sup-

port this feature as well as automatic sample rate switching and auto-

matic sample rate detection.

Please check if your computer support USB 2.0 interface prior to installing

AMI MUSIK DS5. Install USB 2.0 supporting PCI card, PCI-e card, or USB

card device if it does not support it.

Recommended hardware configuration

• Intel Pentium 4 i3 and up CPU or same level AMD CPU

• 4G and up RAM

• USB 2.0 port

• Microsoft Windows 7 and up / Mac OS X 10.6.4 and up / Linux Kernel

2.6.37 and up

• 7200rpm UDMA 133 supporting hard disk

• DVD-ROM 16X and up

※or Windows users, you need to first install the driver and then con-

nect the device with your PC.

(1) icrosoft Windows PC (XP, Vista, 7 & 8)

Windows PCs need a driver installation in order to playback music using

an asynchronous USB Audio Class 2(UAC2) device. Setup will require

that you connect the device with your computer once the driver is in-

stalled.

1) icrosoft Windows Vista, 7 & 8 installation

Open the explorer and click on the icon of your CD/DVD drive. Double-

click

setup_(ami_ds5_v )AMI MUSIK DS5 Setup

Click on

Yes

to continue

Click on

Install

to continue

Click on

to continue

AMI International, Inc.

Click on

Install

to continue

Complete the installation by clicking

Finish.

Once the driver is successfully installed, ASIO installation driver will

automatically launch.

Click on

to continue

*If you do not need the ASIO driver, click on

Cancel

and

go to the next step.

Verify the folder or make changes to the folder and click on

Complete the installation by clicking

Connect your device to the computer and power on.

※Powering on A I USIK DS5:

Connect the supplied 5V DC adaptor power supply to the AMI MUSIK

DS5 and connect to your PC using the supplied USB cable. Push the vol-

ume button for approximately 1 second. The LED indicators at the front

panel will illuminate for unit initialization. After initialization, the AMI

MUSIK DS5 will be ready for use. The quad level LED indicators shows

will first show the current volume setting and then, the current sample

rate.

AMI MUSIK DS5 Owner’s manual

After successful installation of the driver, click on

Start

→

Control

Panel.

Select

A I DS5 DSD DAC 24/192

as playback device and set

it as default by clicking

Set Default.

Click

Properties

button and then select

Advanced

tab and you can

adjust and test the output format as required.

2) icrosoft Windows XP installation

Open the explorer and click on the icon of your CD/DVD drive. Double-

click

setup_(ami_ds5_v )A I USIK DS5 Setup.

Click on

Install

to continue

Click on

to continue

AMI International, Inc.

Complete the installation by clicking

Finish.

Connect and proceed to

the next installation.

Click on

to continue

Verify the folder or make changes to the folder and click on

Complete the installation by clicking

Your driver installation is now complete.

※Powering on A I USIK DS5:

Connect the supplied 5V DC adaptor power supply to the AMI MUSIK

DS5 and connect to your PC using the supplied USB cable. Push the vol-

ume button for approximately 1 second. The LED indicators at the front

panel will illuminate for unit initialization. After initialization, the AMI

MUSIK DS5 will be ready for use. The quad level LED indicators shows

will first show the current volume setting and then, the current sample

rate.

After installation of the driver package, Windows automatically starts

Found New Hardware Wizard.

Click on

No, not this time

and Click

to continue.

AMI MUSIK DS5 Owner’s manual

Select

Install the software automatically [Recommended]’

and click

Click on

Continue Anyway

Complete the installation by clicking

Finish.

After successful installation of the driver, Click on

Start

→

Control

Panel.

Select

A I DS5 DSD DAC 24/192

as playback device.

(2) Apple ac OSX 10.6.4 or higher, Linux Kernel 2.6.37 or higher

The OS embedded UAC2 driver is installed automatically when the AMI

MUSIK DS5 is connected. No third party driver installation is needed.

Simply connect your AMI MUSIK DS5 to a free USB port on your Apple

Mac or Linux computer using the USB cable supplied.

Open inder > Go to

Utilities > Audio IDI Setup

AMI International, Inc.

① Select

A I DS5 DSD DAC 24/192

② Click on the setting button

③ Click on

Use this device for sound output’

as playback device

and set it as default.

You can select the output format

※Note: The AMI MUSIK DS5 support up to 192000.0 Hz only.

Dimensions

Digital inputs

Analog

outputs

Headphone

Output

Power

Supply

• 150 x 40 x 140mm (W x H x D)

• USB HS 2.0 (USB Audio CLASS 2.0 / DSD over

USB PCM token A05 / PCM, DSD Native Stream)

- Support PCM 24bit/192kHz

- Support DSD 64 (2.8MHz) / DSD 128 (5.6MHz)

• Optical x 1EA (50Mbps/192kHz max / WM8804)

• Coaxial x 1EA (75Ω/192kHz max / WM8804)

• D/A converter: Cirrus Logic CS4398 (120dB,

192kHz multibit DAC)

- Dynamic range: 120dB A-Weighted (component

spec)

- Signal noise ratio: 120dB A-Weighted (component

spec)

- THD+N: 0.0005% (component spec)

- Supported PCM sampling rates: 44.1 / 48 / 88.2 /

96 / 176.4 / 192 kHz

- Supported DSD SCLK frequency: DSD64 (2.8MHz)

/ DSD128 (5.6MHz)

- Matched PCM / DSD analog level out (2.2Vrms

pair)

• 2 RCA x 1EA (2.2Vrms, gold plated RCA output)

• 6.3mm phone jack x 1EA (2Vrms max, gold plated

6.3 headphone jack output)

- Supported headphone impedance: 16-300Ω

- Output level: 150mW(16Ωloaded)

- requency response 20Hz~48kHz

- THD 0.02%@1kHz

• Type: 2.1mm DC Jack (external power input)

• Maximum input: 5VDC 3A

• Over voltage protection: 5.5VDC limit (shutdown

operation)

Specifications

Andere Handbücher für Musik DS5

Inhaltsverzeichnis

Andere AMI Verstärkerzubehör Handbücher

AMI

AMI 26685001 Bedienungsanleitung

Beliebte Verstärkerzubehör Handbücher anderer Marken

Crown

Crown Com-Tech CT-1610 Bedienungsanleitung

powersoft

powersoft DSP LITE Bedienungsanleitung

Musical Concepts

Musical Concepts PA-7 Bedienungsanleitung

Schiit

Schiit LISST Bedienungsanleitung

QSC

QSC SF-1 Bedienungsanleitung

Kessler Engineering

Kessler Engineering TL-922 Revival (tm) Bedienungsanleitung

Schiit

Schiit Yggdrasil+ Bedienungsanleitung

GAI-Tronics

GAI-Tronics 12565-001 Betriebsanleitung

Schertler

Schertler RESOCOIL Bedienungsanleitung

powersoft

powersoft KDSP Technisches Datenblatt

ESX

ESX Direction DC1500 Bedienungsanleitung

Apollo creative

Apollo creative Sound Panel Plus Bedienungsanleitung

Roland

Roland CB-CS1 Bedienungsanleitung

JL Audio

JL Audio M-RBC-1 Bedienungsanleitung

Audiosystem

Audiosystem MOSCONI RTC-MOS Bedienungsanleitung

Crown

Crown VCA-MC4A Bedienungsanleitung

Audiosystem

Audiosystem LIT-Logo Bedienungsanleitung

Audiosystem

Audiosystem MOSCONI AS LED FRAMES Bedienungsanleitung