Ampac FireFinder NZS 4512 Bedienungsanleitung

ADVANCED WARNING

SYSTEMS

LED Annunciator Master (LAM) NZS4512

Installation Guide Item Numbers: 4310-0038

MAN2687-1

N1236

Page 1

WORLD LEADER OF INNOVATIVE SOLUTIONS IN FIRE DETECTION AND ALARM SYSTEMS

Ampac Technologies Australia Tel: +61 8 9201 6100 Europe Tel: +44 (0) 1302 833 522 New Zealand Tel: +64 9 443 8072 www.ampac.net

Description:

The LAM and IP40 housing is supplied assembled and

ready to be mounted to any flat surface.

Features:

Remote alarm & fault / isolate zone indication (8 zones)

Remote FACP status indication

Lamp test and buzzer silence controls

ZoneSense PLUS Max 8 LAM’s per FACP (addresses

1-8)

Slip in label for Zone 1-8 or site specific information

(see LAB2656.DOC)

Programmed zones 1 (top) to 8 (bottom)

Installation:

Observe anti-static precautions at all times

1. Power down the FACP, disconnect the batteries

Release of the Clip On Surround: Push down

here, pull out and lift up to remove and insert label.

Lettering on slip in

label must be at

least 5mm in height.

Slip In Label

FIRE

DEFECT / ISOLATE

Windows for

Slip in Label

NOTE:

PCB

FIRE

DBA

DEFECT

NORMAL

SOUNDERDEFECT

ISOLATED

POWER

LAMP

TEST

SILENCE

BUZZER

FIRE

DEFECT/ISOLATE

Figure 1: Inserting Optional Site Label

2. Open the front door and remove the four (4) screws

securing the front cover to the housing.

3. Install an appropriate coupling into the housing

then mount using the three (3) knockout mounting

holes

4. See Figures 1 and 2if site specific label is to be

fitted

5. Set the address (1 to 8) on the LAM as in Figure 2

6. See Figure 3 for information on inserting the

termination link LK1 on the last card in the chain

7. Reassemble

8. Terminate the cabling from the FACP to the LAM

as shown in Figure 3

9. Power up, connect the batteries and test

PWR OUT

PWR IN

+24V

COM

RS 485 OUT TO NEXT LAM

BUZZER MUTE INPUT

LINK

TERMINATOR

ADDRESS SWITCH

SET TO 1

LK1

CN6

1 2 3 4

+24V

COM

+ - SHLD

RS485

AUX

24VDC

RS 485 IN FROM FACP

PWR

OUT

PWR

+24V

COM

RS 485 OUT TO

NEXT LAM

LINK

TERMINATOR

LK1

CN6

1 2 3 4

+24V

COM

RS 485 IN FROM

PREVIOUS LAM

+24V

COM

CN6

1 2 3 4

+24V

COM

BUZZER MUTE INPUT

LAM 1

LAM 2

LAM 3

Field

Termination

in FACP

+ -

ADDRESS SWITCH

SET TO 2

ADDRESS SWITCH

SET TO 3

NOT USED - ONLY USED ON THE LAST LAM IN

THE CHAIN REMOVE AND STORE AS SHOWN

NOT USED - ONLY USED ON THE LAST LAM IN

THE CHAIN REMOVE AND STORE AS SHOWN

LINK

TERMINATOR

LK1

ONLY INSERTED ON THE LAST CARD

PWR

RS 485 OUT TO

NEXT LAM

RS 485 IN FROM

PREVIOUS LAM

PWR

OUT

Figure 2: General Wiring of 3 LAM's

ADVANCED WARNING

SYSTEMS

LED Annunciator Master (LAM) NZS4512

Installation Guide Item Numbers: 4310-0038

MAN2687-1

N1236

Page 2

WORLD LEADER OF INNOVATIVE SOLUTIONS IN FIRE DETECTION AND ALARM SYSTEMS

Ampac Technologies Australia Tel: +61 8 9201 6100 Europe Tel: +44 (0) 1302 833 522 New Zealand Tel: +64 9 443 8072 www.ampac.net

Housing Knockout

Mounting Holes

The LAM Clips into the Facia which in turn is bolted to the front cover.

To insert labels remove the facia and follow the Figure 1 instructions

Front Cover

Door and

Securing Screws

Knockout

Coupling

Conduit

Housing

ALARM

FAULT

ISOLATED

EXTBELLFAULT

WARNSYSTEMFAULT

ACFFAULT/ISOLATED

ASEFAULT

POWER

LAMP

TEST

SILENCE

BUZZER

FAULT/ISOLATE

ALARM

Product Information Label Underneath

Facia

Retaining

Screws &

Washers

DO NOT

OVERTIGHTEN

Figure 3: General Wiring Diagram

Andere Handbücher für FireFinder NZS 4512

Dieses Handbuch passt für folgende Modelle

Andere Ampac Feueralarm Handbücher

Beliebte Feueralarm Handbücher anderer Marken

Zeta Alarm Systems

Zeta Alarm Systems INFINITY ID2 Bedienungsanleitung

System Sensor

System Sensor 22051TLE-RF-26 Bedienungsanleitung

Pittway

Pittway Notifier AM2020 Bedienungsanleitung

Kidde

Kidde VM-1 Produkthandbuch

LST

LST SIM016-3 Bedienungsanleitung

Fireboy- Xintex

Fireboy- Xintex FBD-MZ Originalbetriebsanleitung

bolid

bolid S2000-IP-03 Bedienungsanleitung

GST

GST DI-9204 Bedienungsanleitung

E2S

E2S BExTBG05D Bedienungsanleitung

Notifier

Notifier UZC-256 Bedienungsanleitung

Fire-Lite Alarms

Fire-Lite Alarms MS-2 Bedienungsanleitung

Siemens

Siemens FDOOT221 Bedienungsanleitung

hyfire

hyfire HY5000 Series Bedienungsanleitung

FlameStop

FlameStop PFSIFP8 Bedienungsanleitung

Radionics

Radionics Radionics 9124 Bedienungsanleitung

UniPOS

UniPOS FD 7120 Bedienungsanleitung

FIREWOLF

FIREWOLF FW-C01224 Bedienungsanleitung

Siemens

Siemens MH-5 Series Service-Handbuch