Amphony iFinityr Handbuch
User and Installation
Guide
Digital Wireless
Indoor / Outdoor Speaker
iFini yt
TM
R
Contents:
Unpacking .......................................................................................
Connecting power ...........................................................................
Selecting the audio channel ...........................................................
Turning on speaker power ..............................................................
Pairing the speaker and transmitter ................................................
Setting the speaker volume and treble ...........................................
Troubleshooting ..............................................................................
Technical specifications ..................................................................
Safety information ...........................................................................
Limited warranty ............................................................................
1
1
3
4
5
6
7
8
9
11
Step 1 Connecting power
After placing the speaker in a safe environment, make sure that you
have not yet plugged the AC adapter into an outlet. Next, insert the
barrel-shaped plug of the supplied AC adapter into the opening at the
rear of the speaker which says “DC 36V“.
Ensure that you insert the plug straight into the opening (do not angle
it). Push it until it is inserted securely.
Next, plug the AC adapter into a power outlet.
Unpacking: Check that this package contains:
One speaker, one AC adapter (wallwart)
In order to operate your wireless speaker, you need
an Amphony iFinity audio transmitter (sold separately). If you have
purchased a full set, the transmitter is already part of the set and is
packaged separately. Please refer to the transmitter user guide for
operation instructions.
Important Note:
User and Installation Guide
R
Page 1
ATTENTION
Connect the supplied AC adapter
to the speaker connecting
the AC adapter to an outlet to avoid
spark generation.
BEFORE
DC 36 V
Power outlet
AC adapter
Left Right
Mono
Treble Volume Pairing
Network
DC 36V
Off On
iFini yt
TM
User and Installation Guide
R
Page 2
Connecting power
Left Right
Mono
Treble Volume Pairing
Network
DC 36V
Off On
iFini yt
TM
User and Installation Guide
R
Page 3
Step 2 Selecting the audio channel
Slide the audio-channel switch to the audio channel which you want
the speaker to receive. You can either receive the left audio channel,
the right channel or a mix between both channels (mono).
If you are using two wireless speakers in one room, you want to set
one speaker to receive the left channel and one speaker to receive
the right channel.
Channel-select switch
Left Right
Mono
Treble Volume Pairing
Network
DC 36V
Off On
iFini yt
TM
User and Installation Guide
R
Page 4
Step 3 Turning on speaker power
Turn the speaker volume control to the minimum position.
Next, slide the on/off switch into the “On“ position.
The network status light should start flashing.
On/Off switch
Network
status light
Volume control
Turn to
minimum
Left Right
Mono
Treble Volume Pairing
Network
DC 36V
Off On
iFini yt
TM
User and Installation Guide
R
Page 5
Step 4 Pairing the speaker and transmitter
To receive audio from the transmitter, set the transmitter into pairing
mode by pushing the transmitter pairing button.
Then, push the pairing button of the speaker within 5 minutes.
After the speaker is paired with the transmitter, the network status
light will stop flashing and light continuously and the speaker should
output the audio from the transmitter.
Pairing button
Network
status light
Left Right
Mono
Treble Volume Pairing
Network
DC 36V
Off On
iFini yt
TM
User and Installation Guide
R
Page 6
Step 5 Setting the speaker volume and treble
Now slowly increase the volume control.
Use the treble control to adjust the treble of your speaker.
Please follow the instructions in the transmitter user guide for
adjusting the transmitter properly to your audio source in order to
maximize the dynamic range of your speaker.
Treble control Volume control
User and Installation Guide
R
Page 7
Troubleshooting
Problem
No Sound - Network
status light is OFF
No Sound - Network
status light is
FLASHING
No Sound - Network
status light is ON
Possible Cause
AC adapter not
plugged in properly
Speaker not
switched on
No wireless signal
Speaker not paired
with transmitter
Strong interference
Volume control set
too low
No audio at
transmitter
Solution
Check AC adapter for
proper fit
Slide the speaker on/off
switch to the “On“ setting
Check if the transmitter is
active
Pair the speaker with the
transmitter
Try eliminating
interference at 2.4 GHz
(wireless LANs, cordless
phones), try relocating
the transmitter or speaker
to improve reception
Adjust the transmitter and
speaker volume control
Verify that audio is
supplied to the
transmitter, check the
audio connection to the
transmitter
Please check the network status light of the speaker and then choose
from the following problems:
User and Installation Guide
R
Page 8
Technical Specifications
Amplifier:
Amplifier Power:
Drivers:
Crossover:
Frequency response (-6 dB):
Amplifier distortion (THD):
Power efficiency:
Max. number of speakers
per transmitter:
Size:
Weight:
Standby power:
Bi-amplification: two separate
Class-D amplifiers
150W peak, 80W rms
5" woofer, 1" tweeter
Active
60 Hz - 18 kHz
0.06% @ 50 Watts
91%
4
8.5" (H) x 8.5" (W) x 8.3" (D)
4.8 lbs
< 3W
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Amphony Sprecher Handbücher
Beliebte Sprecher Handbücher anderer Marken
Bowers & Wilkins
Bowers & Wilkins 4 Bedienungsanleitung
Sonance
Sonance SONOS OUTDOOR Series Bedienungsanleitung
Electro-Voice
Electro-Voice EVID FM4.2 Bedienungsanleitung
Pioneer
Pioneer XW-HTD630 Bedienungsanleitung
Onn
Onn BWA16AA002 Bedienungsanleitung
HP
HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung