Amprobe AM535 Bedienungsanleitung

AM-535-EUR

Digital Multimeter

User Manual

6/2015, 6005740 A

English

Limited Warranty and Limitation of Liability

Your Amprobe product will be free from defects in material and workmanship for one

year from the date of purchase unless local laws require otherwise. This warranty does

not cover fuses, disposable batteries or damage from accident, neglect, misuse, alteration,

contamination, or abnormal conditions of operation or handling. Resellers are not authorized

to extend any other warranty on the behalf of Amprobe. To obtain service during the

warranty period, return the product with proof of purchase to an authorized Amprobe

Service Center or to an Amprobe dealer or distributor. See Repair Section for details. THIS

WARRANTY IS YOUR ONLY REMEDY. ALL OTHER WARRANTIES - WHETHER EXPRESS, IMPLIED

OR STATUTORY - INCLUDING IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE

OR MERCHANTABILITY, ARE HEREBY DISCLAIMED. MANUFACTURER SHALL NOT BE LIABLE

FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES,

ARISING FROM ANY CAUSE OR THEORY. Since some states or countries do not allow the

exclusion or limitation of an implied warranty or of incidental or consequential damages, this

limitation of liability may not apply to you.

Repair

All Amprobe returned for warranty or non-warranty repair or for calibration should be

accompanied by the following: your name, company’s name, address, telephone number,

and proof of purchase. Additionally, please include a brief description of the problem or

the service requested and include the test leads with the meter. Non-warranty repair or

replacement charges should be remitted in the form of a check, a money order, credit card

with expiration date, or a purchase order made payable to Amprobe.

In-warranty Repairs and Replacement – All Countries

Please read the warranty statement and check your battery before requesting repair. During

the warranty period, any defective test tool can be returned to your Amprobe distributor

for an exchange for the same or like product. Please check the “Where to Buy” section on

Canada, in-warranty repair and replacement units can also be sent to an Amprobe Service

Center (see address below).

Non-warranty Repairs and Replacement – United States and Canada

Non-warranty repairs in the United States and Canada should be sent to an Amprobe Service

Center. Call Amprobe or inquire at your point of purchase for current repair and replacement

rates.

USA: Canada:

Amprobe Amprobe

Everett, WA 98203 Mississauga, ON L4Z 1X9

Tel: 877-AMPROBE (267-7623) Tel: 905-890-7600

Non-warranty Repairs and Replacement – Europe

European non-warranty units can be replaced by your Amprobe distributor for a nominal

distributors near you.

AM-535-EUR Digital Multimeter

1Flash light

2LC Display

3Function Buttons

4Flash light Button

5Rotary Switch

6SELECT Button

7Input Terminal for voltage, diode, capacitance,

Resistance, continuity and temperature measurement

8COM (return) terminal for all measurements

9Input Terminal for AC/DC mA/uA measurement

10 Input Terminal for AC/DC A measurement up to 20A

Screen Display

1The Meter selects the range with best resolution

2Direct Current

3Negative reading

4Alternate Current

5Low battery indicator

6Data hold

7Diode test

8Continuity test

9Relative zero mode

10 Non-Contact Voltage

11 Measurement units for Resistance

12 Measurement units for Frequency

13 Measurement units for Voltage

14 Measurement units for Current

15 Measurement units for Capacitance

16 Auto Power Off

17 Maximum / minimum reading memory

18 Measurement unit for Temperature

19 Analog bar graph display

6 8 7

10 13 14 1517

AM-535-EUR Digital Multimeter

CONTENTS

SYMBOL.................................................................................................................2

SAFETY INFORMATION .........................................................................................2

UNPACKING AND INSPECTION .............................................................................3

FEATURES...............................................................................................................4

MAKING MEASUREMENT .....................................................................................5

Measuring AC and DC Voltage.........................................................................6

Measuring AC and DC Current.........................................................................7

Measuring Resistance .......................................................................................8

Measuring Continuity.......................................................................................9

Measuring Diode...............................................................................................9

Measuring Capacitance ....................................................................................10

Measuring Frequency .......................................................................................10

Measuring Temperature °C /°F .........................................................................11

Non-Contact Voltage Sensing ..........................................................................12

SPECIFICATION.......................................................................................................13

MAINTENANCE......................................................................................................16

BATTERY AND FUSE REPLACEMENT.....................................................................17

SYMBOLS

Caution ! Risk of electric shock.

Caution! Refer to the explanation in this Manual

Alternating Current (AC)

Direct Current (DC)

The equipment is protected by double insulation or reinforced

insulation

Earth (Ground)

Audible tone

Battery

Complies with European Directives

Conforms to relevant Australian standards

Canadian Standards Association (NRTL/C)

Do not dispose of this product as unsorted municipal waste.

Contact a qualified recycler.



SAFETY INFORMATION

The Meter complies with:

IEC/EN 61010-1 3rd Edition, UL61010-1 2nd Ed. and CAN/CSA C22.2 No.

61010.1-0.92 to Category III 600 Volts, Pollution degree 2

IEC/EN 61010-2-030

IEC/EN 61010-031 for test leads

EMC IEC/EN 61326-1

Measurement Category III (CAT III) is for measurements performed in the

building installation. Examples are measurements on distribution boards,

circuit- breakers, wiring, including cables, bus-bars, junction boxes, switches,

socket-outlets in the fixed installation, and equipment for industrial use

and some other equipment, for example, stationary motors with permanent

connection to the fixed installation.

Measurement Category II (CAT II) is for measurements performed on circuit

directly connected to low voltage installation. Examples are measurements on

household appliances, portable tools and similar equipments.



Warning: Read Before Using

• To avoid possible electrical shock or personal injury, follow these

instructions and use the Meter only as specified in this manual.

• Do not use the Meter or test leads if they appear damaged, or if the

Meter is not operating properly. If in doubt, have the Meter serviced.

• Always use the proper function and range for measurements.

• Before rotating the function range selection switch, disconnect test

probe from circuit under test.

• Verify the Meter’s operation by measuring on a known voltage source.

• Do not apply more than the rated voltage, as marked on the Meter,

between the test probe or between any test probe and earth ground.

• Use the Meter with caution for voltages above 30 Vac rms, 42 Vac peak,

or 60 Vdc. These voltages pose electrical shock hazards.

• Disconnect circuit power and discharge all high-voltage capacitors before

testing resistance.

• Do not use the Meter around explosive gas or vapor.

• When using the test leads, keep your fingers behind the finger guards.

• Remove test leads from the Meter before opening the Meter case or

battery door.

UNPACKING AND INSPECTION

Your shipping carton should include:

1 AM-535-EUR

1 Pair of test leads

1 Temperature probe

1 Velcro strap

1 9V (6F22) battery (installed)

1 User manual

1 Carrying case

If any of the items are damaged or missing, return the complete package to

the place of purchase for an exchange.

FEATURES

AM-535-EUR is the fully-featured multimeter of choice for the professional

electrical contractor. Measure and verify presence of voltage in order to

connect equipment or to perform repairs, run new wiring, check continuity

of electrical connections, identify blown fuses, troubleshoot motors or check

transformers. The AM-535-EUR features Truerms sensing to accurately measure

voltage on systems affected by harmonics, a built in flashlight to detect wire

colors in the dark, a “third hand” probe holder and non-contact voltage

detection. Safety rated to CAT III 600V.

• Measurements: Voltage up to 600VAC and 600VDC, AC/DC current,

Resistance, Frequency, Capacitance, Temperature.

• Frequency, Capacitance, Duty Cycle for troubleshooting applications

• Special Functions:

- Non-contact Voltage Detection

- Audible continuity

- Diode Test

• Backlight LC Display with analog bar graph

• Events:

- Data hold

- MAX / MIN Memory

- Relative zero mode

• Built in work light (flashlight)

• Built in test leads storage and “third hand holder”

• Auto and Manual ranging

• Auto power off

• Low battery warning

• Velcro strap to hang a meter

• Safety: CAT III 600V

MAKING MEASUREMENT



1. Use the proper function and range for measurements.

2. To avoid possible electrical shock, personal injury or damages to the

Meter, disconnect circuit power and discharge all high-voltage capacitors

before testing resistance and diode.

3. Connecting test leads:

• Connect the common (COM) test lead to the circuit before connecting

the live lead

• After measurement, remove live lead before removing the common

(COM) test lead from the circuit

4. Symbol “OL” is displayed on LCD when the measurement is out of range.

Rotary Switch Positions

Switch Position Measurement Function

V AC or DC voltage measurement (use SELECT button for

switching to AC or DC).

Resistance measurement

Voltage measurement of diode PN junction

Continuity measurement

Capacitance measurement

Hz Frequency measurement

°C °F Temperature measurement

NCV Non-contact voltage

μA mA A AC or DC current measurement (use SELECT button for

switching to AC or DC).

Function Buttons

Button Measurement Function

SELECT Switching AC or DC. Press the yellow SELECT button to select

alternate measurement functions on the rotary switch.

HOLD / Display freezes present reading / press 2 sec to turn on

LCD backlight.

REL Relative zero mode

RANGE

Manual or Auto range switching. The default setting

is Auto ranging, press to switch to manual ranging

(selectable resolutions). Press for 2 sec to return to auto

ranging.

MAX/MIN Maximum / minimum reading memory.

Flash light

Press to enable the function when at relevant rotary switch function.

Auto Power OFF

Auto power off: approx. 15 minutes.

When the Meter is in auto power off mode, press any button to resume

normal operation.

Measuring AC and DC Voltage

Press SELECT button to select AC/DC voltage measurement function.

To avoid personal injury or damage to the Meter, do not apply

voltage higher than 600Vac and 600Vdc.

Measuring AC and DC Current

Press SELECT button to select AC or DC current measurement function.

To avoid personal injury or damage to the meter:

1. Do not attempt to make an in-circuit current measurement when the

open-circuit potential to earth ground exceeding AC 600V or DC 600V

2. Switch to proper function and range for your measurement.

3. Do not place the test probe in parallel with a circuit when the test leads

are connected to the current terminals.

4. Connect the test leads to the correct input A/mA μA current terminal and

to the circuit before powering the circuit under test.

5. For current range from 8-10A, do not measure current for more than 20

minutes. Wait for 10 minutes before taking another measurement

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Amprobe Multimeter Handbücher

Amprobe

Amprobe ACDC-100 TRMS Bedienungsanleitung

Amprobe

Amprobe AM-220 Bedienungsanleitung

Amprobe

Amprobe 38XR-A Bedienungsanleitung

Amprobe

Amprobe ACD-14-PRO Bedienungsanleitung

Amprobe

Amprobe AM-20 Bedienungsanleitung

Amprobe

Amprobe ACD-11 Bedienungsanleitung

Amprobe

Amprobe AMP-210 Bedienungsanleitung

Amprobe

Amprobe KWC-2000 Bedienungsanleitung

Amprobe

Amprobe AM-420 Bedienungsanleitung

Amprobe

Amprobe AM-510 Bedienungsanleitung

Amprobe

Amprobe 33XR-A Bedienungsanleitung

Amprobe

Amprobe AM-560 Bedienungsanleitung

Amprobe

Amprobe CR50A Bedienungsanleitung

Amprobe

Amprobe DM73C Bedienungsanleitung

Amprobe

Amprobe DM9C Bedienungsanleitung

Amprobe

Amprobe DM7C Bedienungsanleitung

Amprobe

Amprobe 30XR-A Bedienungsanleitung

Amprobe

Amprobe HD160C Bedienungsanleitung

Amprobe

Amprobe HD160C Bedienungsanleitung

Amprobe

Amprobe AM-520-EUR Bedienungsanleitung

Amprobe

Amprobe 34XR-A Bedienungsanleitung

Amprobe

Amprobe AD105A Bedienungsanleitung

Amprobe

Amprobe AM-1250 Bedienungsanleitung

Amprobe

Amprobe AM-4B Bedienungsanleitung

Beliebte Multimeter Handbücher anderer Marken

Agilent Technologies

Agilent Technologies 34420A Bedienungsanleitung

Fluke

Fluke 83 Bedienungsanleitung

Hameg

Hameg HM 8012 Bedienungsanleitung

Mastech

Mastech MY70 Bedienungsanleitung

Steren

Steren MUL-300 Bedienungsanleitung

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Bedienungsanleitung

PeakTech

PeakTech 4000 Gebrauchs- und Pflegehandbuch

YOKOGAWA

YOKOGAWA 90050B Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Bedienungsanleitung

Fluke

Fluke 8846A Bedienungs- und Wartungshandbuch

Tempo Communications

Tempo Communications MM200 Bedienungsanleitung

Elenco Electronics

Elenco Electronics CM-1555 Bedienungsanleitung

Mastech

Mastech MS8238C Bedienungsanleitung

SDAR

SDAR 830A, 830B, 830D, 830C Bedienungsanleitung

RS PRO

RS PRO RS-9519BT Bedienungsanleitung

BGS technic

BGS technic 8890 Bedienungsanleitung

Morris

Morris 57074 Bedienungsanleitung