Amprobe VPC-10 Bedienungsanleitung

Users Manual

• Mode d’emploi

• Bedienungshandbuch

• Manual d’Uso

• Manual de uso

VPC-10

Voltage & Continuity

Tester

VPC-10

Voltage & Continuity Tester

Users Manual

May 2010, Rev.2

English

Limited Warranty and Limitation of Liability

Your Amprobe product will be free from defects in material

and workmanship for 1 year from the date of purchase. This

warranty does not cover fuses, disposable batteries or damage

from accident, neglect, misuse, alteration, contamination, or

abnormal conditions of operation or handling. Resellers are not

authorized to extend any other warranty on Amprobe’s behalf.

To obtain service during the warranty period, return the product

with proof of purchase to an authorized Amprobe Test Tools

Service Center or to an Amprobe dealer or distributor. See Repair

Section for details. THIS WARRANTY IS YOUR ONLY REMEDY.

ALL OTHER WARRANTIES - WHETHER EXPRESS, IMPLIED OR

STAUTORY - INCLUDING IMPLIED WARRANTIES OF FITNESS FOR

A PARTICULAR PURPOSE OR MERCHANTABILITY, ARE HEREBY

DISCLAIMED. MANUFACTURER SHALL NOT BE LIABLE FOR ANY

SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES

OR LOSSES, ARISING FROM ANY CAUSE OR THEORY. Since some

states or countries do not allow the exclusion or limitation of an

implied warranty or of incidental or consequential damages, this

limitation of liability may not apply to you.

Repair

All test tools returned for warranty or non-warranty repair or

for calibration should be accompanied by the following: your

name, company’s name, address, telephone number, and proof of

purchase. Additionally, please include a brief description of the

problem or the service requested and include the test leads with

the meter. Non-warranty repair or replacement charges should be

remitted in the form of a check, a money order, credit card with

expiration date, or a purchase order made payable to Amprobe®

Test Tools.

In-Warranty Repairs and Replacement – All Countries

Please read the warranty statement and check your battery before

requesting repair. During the warranty period any defective test

tool can be returned to your Amprobe® Test Tools distributor

for an exchange for the same or like product. Please check the

“Where to Buy” section on www.amprobe.com for a list of

distributors near you. Additionally, in the United States and

Canada In-Warranty repair and replacement units can also be sent

to a Amprobe® Test Tools Service Center (see address below).

Non-Warranty Repairs and Replacement – US and Canada

Non-warranty repairs in the United States and Canada should be

sent to a Amprobe® Test Tools Service Center. Call Amprobe® Test

Tools or inquire at your point of purchase for current repair and

replacement rates.

In USA In Canada

Amprobe Test Tools Amprobe Test Tools

Everett, WA 98203 Mississauga, ON L4Z 1X9

Tel: 877-AMPROBE (267-7623) Tel: 905-890-7600

Non-Warranty Repairs and Replacement – Europe

European non-warranty units can be replaced by your Amprobe®

Test Tools distributor for a nominalv charge. Please check the

“Where to Buy” section on www.amprobe.com for a list of

distributors near you.

European Correspondence Address*

Amprobe® Test Tools Europe

In den Engematten 14

79286 Glottertal, Germany

Tel.: +49 (0) 7684 8009 - 0

*(Correspondence only – no repair or replacement available from

this address. European customers please contact your distributor.)

1) Measuring Probe (Pos)

2) Ground Probe (COM)

3) Negative DC voltage Detection LED indication

4) Positive DC voltage Detection LED indication

5) AC Voltage range

6) DC voltage range

7) AC voltage Detection LEDs

8) Continuity LED indication

VPC-10 Voltage & Continuity Tester

CONTENTS

SYMBOLS.......................................................................... 2

UNPACKING AND INSPECTION ....................................... 2

INTRODUCTION ................................................................ 3

OPERATION....................................................................... 3

Automatic Operation................................................... 4

Voltage Measurement ................................................. 5

Continuity Testing ....................................................... 7

SPECIFICATION ................................................................. 10

MAINTENANCE AND REPAIR ........................................... 11

BATTERY REPLACEMENT ................................................. 12

SYMBOLS

Battery

Warning! Dangerous Voltage

Double Insulation

Caution! Refer to the user’s manual before

using this Meter.

Alternating Current (AC).

Ground (maximum permitted voltage between

terminal and ground).

Direct Current (DC).

Symbol

Application around and removal from

hazardous live conductors is permitted

Complies with European Directives

Do not dispose of this product as unsorted

municipal waste

Conforms to relevant Australian standards

Underwriters Laboratories.

[Note: Canadian and US.]

Audible tone

WARNING

identiﬁes conditions and actions that could result in

serious injury or even death to the user.

CAUTION

identiﬁes conditions and actions that could cause

damage or malfunction in the unit.

This manual contains information and warnings that

must be followed for operating the tester safely and

maintaining the tester in a safe operating condition.

If the tester is used in a manner not speciﬁed by the

manufacturer, the protection provided by the tester may

be impaired. Do not use in rainfall!

The tester is protected, against the users, by double

insulation per EN61010-1 2nd Ed to CAT III 600V.

WARNING

To reduce the risk of ﬁre or electric shock, do not

expose this product to rain or moisture. To avoid

electrical shock hazard, observe the proper safety

precautions when working with voltages above

60 VDC or 30 VAC rms. These voltage levels pose a

potential shock hazard to the user.

• Keep your hands / ngers behind the hand /

ﬁnger barriers of the test probes that indicate the

limits of safe access of the hand-held part during

measurement. Inspect test probes, connectors, and

probes for damaged insulation or exposed metal

before using the tester. If any defects are found,

replace them immediately.

• The voltages marked on the tester are nominal

voltages or nominal voltage ranges. The tester

shall only be used on installations with the

speciﬁed nominal voltages or nominal voltage

ranges.

• Never apply more than 600V DC or 600V AC rms.

between any terminal and earth ground.

• indicates dangerous voltage present if the LED

turns on.

• When using the probes, do not touch the metal

probe tips.

• Disconnect the live test lead before disconnecting

the common test lead.

• Before each use, verify the tester’s operation by

measuring a known voltage.

UNPACKING AND INSPECTION

Your shipping carton should include:

1 VPC-10 Voltage Tester

1 Users Manual

2 1.5V AAA LR03/NEDA 24A Batteries (Installed)

If any of the items are damaged or missing, return

the complete package to the place of purchase for an

exchange.

INTRODUCTION

The VPC-10 and voltage tester is designed to be rugged

and easy to use for the testing of voltage and continuity.

It comes with a buzzer that provides indication of

voltage or continuity. Full input protection to CAT III

600V.

• Automatically turns ON and OFF for easy and

quick measurements

• Automatically selects AC Voltage, DC Voltage or

Continuity

• LED’s indicate 7 levels of AC and DC Voltages:

• Volts (AC) 24, 120, 208, 240, 277, 480, 600

• Volts (DC) 6, 12, 24, 36, 48,110, 220

• Continuity buzzer and Visual continuity indication

(LED)

• Safety CAT III 600 V

Andere Handbücher für VPC-10

Inhaltsverzeichnis

Andere Amprobe Prüfgeräte Handbücher

Amprobe

Amprobe VPC-30 Bedienungsanleitung

Amprobe

Amprobe BAT-250 Bedienungsanleitung

Amprobe

Amprobe BAT-200 Bedienungsanleitung

Amprobe

Amprobe CT235A Bedienungsanleitung

Amprobe

Amprobe ST-101B Originalbetriebsanleitung

Amprobe

Amprobe LT-10 Bedienungsanleitung

Amprobe

Amprobe gp-2a Bedienungsanleitung

Amprobe

Amprobe A-5000 Bedienungsanleitung

Amprobe

Amprobe BT-120 Bedienungsanleitung

Amprobe

Amprobe LAN-1 Bedienungsanleitung

Amprobe

Amprobe 3503229 Bedienungsanleitung

Amprobe

Amprobe RS-3 PRO CAT IV Analog Bedienungsanleitung

Amprobe

Amprobe BT-120 Bedienungsanleitung

Amprobe

Amprobe AMB-55 Bedienungsanleitung

Amprobe

Amprobe LT-10-EUR Bedienungsanleitung

Amprobe

Amprobe PY-1A Bedienungsanleitung

Amprobe

Amprobe BAT-200 Bedienungsanleitung

Amprobe

Amprobe INSP-3 Bedienungsanleitung

Amprobe

Amprobe PRM-6 Bedienungsanleitung

Amprobe

Amprobe AMB-45 Bedienungsanleitung

Amprobe

Amprobe ACD-14 FX Bedienungsanleitung

Amprobe

Amprobe AT-2004-A Bedienungsanleitung

Amprobe

Amprobe SM-CAL1 Bedienungsanleitung

Amprobe

Amprobe UAT-505 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung