AMT Pumps 4S14KLR Bedienungsanleitung

Specications Information and Repair Parts Manual 4S14KLR, 4S13XHR & 4S13XZR

4SXX-251-00 1 6/2023

Please read and save this Repair Parts Manual. Read this manual and the General Operating Instructions carefully before attempting to assemble, install, operate

or maintain the product described. Protect yourself and others by observing all safety information. The Safety Instructions are contained in the General Operating

Instructions. Failure to comply with the safety instructions accompanying this product could result in personal injury and/or property damage! Retain instructions

for future reference. AMT reserves the right to discontinue any model or change specications at any time without incurring any obligation.

Periodic maintenance and inspection is required on all pumps to ensure proper operation. Unit must be clear of debris and sediment. Inspect for leaks and loose bolts. Failure to do so

voids warranty.

4-INCH IPT TRASH PUMP

Refer to pump manual 1808-633-00 for General Operating and Safety Instructions.

UNPACKING

Refer to Repair Parts Illustration and Repair Parts List to aid in

identifying parts. Unpack and separate all pump components

from container making sure all parts are accounted for.

Packages should contain:

1. Pump and engine completely assembled on roll frame.

2. Battery tray (Ref. No. 44) and battery tray hardware (E-start

models only).

3. 4” NPT Strainer.

ASSEMBLY

(Refer to Figure 3)

1. Remove pump from packaging.

2. Refer to engine manual for proper wiring instructions. Be

sure to route and secure battery cable safely UNDER

pump where it will not be pinched or come in contact with

hot engine exhaust or mu󰀪er (see Figure 1).

3. Electric Start Models Only:

Install a 12 volt type no. 9A1 garden tractor battery 32 amp

hour rating, approx. size 7¾” L x 5” W x 6” H (not included)

onto battery tray. Using hardware included with pump,

insert hook bolts through battery tray holes, thread facing

up. Attach battery box hold down bar across battery and

thread wing nuts onto hook bolts.

MAINTENANCE

MECHANICAL SEAL REPLACEMENT

Refer to Figures 2 and 3

NOTE: Always replace the seal seat (Ref. No. 12), seal head

(Ref. No. 13) and shaft sleeve (Ref. No. 3) to ensure proper

mating of mechanical seal components!

1. Unthread cap screws (Ref. No. 20) and remove casing

(Ref. No. 19) and casing seal (Ref. No. 37) from casing

cover (Ref. No. 6).

2. Unthread screws (Ref. No. 15) and remove volute (Ref. No.

14) from casing cover.

3. Unscrew impeller (Ref. No. 2) from the engine shaft.

Remove the impeller shim (Ref. No. 5), shaft sleeve and

seal head from engine shaft. Use a rubber mallet or soft

block of wood to loosen impeller. Turn it counterclockwise

Disconnect spark plug wire and battery to prevent

accidental starting.

4. Unthread cap screws (Ref. No. 9) and remove the adapter

(Ref. No. 7) and casing cover from the engine mounting

face.

5. Push seal seat from the casing cover recess with a

screwdriver.

6. Clean the casing cover recess before inserting a new seal

seat.

7. Carefully wipe the polished surface of the new seal seat

with a clean cloth.

8. Wet the rubber portion of the seal seat with a light coating

of soapy water.

DESCRIPTION

This trash pump is a heavy duty, centrifugal, engine-driven, self-priming (to 20 ft. lift after initially lling casing with liquid), portable unit. Pump is equipped with

precision lapped mechanical seal to reduce the likelihood of leakage, and a clog-resistant impeller capable of handling solids, 4” models up to 2” diameter. Units

are used to handle water containing stones, sticks, mud and other solids (up to 25% by volume). Sealed ange connections facilitate easy removal of suction and

discharge lines. Handles liquids from 40º to 180º F (4º to 82º C). For use with nonammable uids compatible with pump component materials.

All models come standard with manual recoil starter. 4” models feature 12 VDC electric start 5” W x 7¾” L x 5” H battery holder included. (Battery not included;

obtain 12V, 32 amp hour battery from local lawn and garden shop). Pump and engine are mounted in steel roll frame, requires minimum 2 people to move or lift.

Four position discharge manifold provides a choice in placing hose.

Figure 1 - Battery Cable

Specications Information and Repair Parts Manual 4S14KLR, 4S13XHR & 4S13XZR

4SXX-251-00 2 6/2023

9. Press the new seal seat squarely into the cavity in the

casing cover. If the seal seat does not press squarely into

the cavity, it can be adjusted in place by pushing on it with

a piece of pipe. Always use a piece of cardboard between

the pipe and the seal seat to avoid scratching the seal

seat. (This is a lapped surface and must be handled very

carefully).

10. After the seal seat is in place, ensure that it is clean and

has not been marred.

11. Using a clean cloth, wipe the shaft and make certain that it

is perfectly clean.

12. Secure the adapter on the engine mounting face.

NOTE: Tighten cap screws EVENLY to avoid cocking rabbet on

engine mounting face.

13. Apply a light coating of soapy water to the inside rubber

portion of seal head and slide onto the shaft sleeve. Slip

the shaft sleeve with seal head onto the engine shaft.

IMPORTANT: Before installing new shaft sleeve, apply a bead

of non hardening, pliable sealant (such as Permatex® Form-A-

Gasket® No. 2) around motor shaft shoulder.

Do not touch or wipe the face of the polished part of the

seal head.

14. Replace any impeller shims removed in disassembly.

15. Screw the impeller back in place tightening until it is seated

against shims and shaft sleeve.

NOTE: Check to be sure that the shaft sleeve (Ref. No. 3) is in

place against engine shaft shoulder. Model 4S13XAR requires

a shaft ange (Ref. No. 4)

16. Remount volute with fasteners.

17. Refer to section titled Shim Adjustment at this time if shaft

sleeve or any other parts listed therein have been replaced.

18. Inspect position of apper valve assembly (Ref. No. 16) to

ensure proper movement and sealing.

19. Replace o-ring seal on volute rabbet.

NOTE: Always inspect o-ring seals. Replace when cracked or

worn. Wet o-ring with soapy water for ease of assembly.

20. Remount casing.

21. Remount any other parts and reconnect spark plug wire

and battery (if so equipped). Pump should now run with

renewed original performance.

SHIM ADJUSTMENT

1. When installing a replacement impeller, engine, shaft

sleeve, adapter, or volute, it may be necessary to vary the

number of impeller shims (Ref. No. 5) that will be required.

This is easily done by adding one shim more than was

removed and reassembling the pump as described in

Mechanical Seal Replacement section.

2. Ensure that volute (Ref. No. 14) and casing cover (Ref. No.

6) are tted rmly (check fastener Ref. No. 15). Remove

spark plug wire from engine and turn engine over by pulling

the recoil starter. If engine does not turn freely, disassemble

pump and remove one shim.

NOTE: When adding or removing shims, it is best to proceed

with a 0.010” increment each time. If engine does turn freely,

add shims until it does strike, then remove a 0.010” shim. This

should allow proper clearance.

3. Proper running clearance is 0.010”.

4. Follow the above procedure until proper clearance is

obtained. This will ensure maximum performance.

IMPELLER AND VOLUTE REPLACEMENT

Impeller (Ref. No. 2) and volute (Ref. No. 14) are subject to

wear only by abrasive sand or sediment laden liquids. If badly

worn, all these parts can be replaced easily and the pump thus

restored to full e󰀩ciency.

NOTE: When the clearance between the impeller and the volute

exceeds 1/16” at the face of the impeller or 1/8” on the outside

diameter of the impeller, it may be necessary to take corrective

action. The increased clearance can cause lengthened priming

times and reduced pumping capacity. If both the priming and

capacity of your unit are satisfactory for your application, it is

recommended that no corrective maintenance be performed

regardless of what clearances on your unit may have developed,

since the increased clearances in themselves are not generally

harmful to your pump. Normally, new pump clearances can

be restored by simply shimming behind the impeller. (Add

shim washers, Ref. No. 5). If the impeller is badly worn it is

recommended that the impeller be replaced. This is usually

all that is required since only on unusually abrasive services

does the cast iron wear plate show deterioration. Occasionally

a stone or hard object might get caught in the impeller and

cause damage to the volute/cut water. In these cases, follow

the instructions below for replacement and refer to Figure 3.

1. Disassemble pump for access as described in

MECHANICAL SEAL REPLACEMENT, steps 1 and 2.

2. Replace parts as necessary.

4-INCH TRASH PUMP

Figure 2 - Mechanical Seal

Specications Information and Repair Parts Manual 4S14KLR, 4S13XHR & 4S13XZR

4SXX-251-00 3 6/2023

NOTE: When replacing volute, attach apper valve assembly

(Ref. No. 16) to new volute with fasteners (Ref. No. 18).

NOTE: Before installing new parts, clean all mating surfaces

thoroughly. For information pertaining to the engine and

engine parts, consult the Engine Manual or contact the nearest

authorized service representative or the manufacturer.

CLEANING

These units are designed so that for most clean out or clogging

problems it should not be necessary to remove hoses or piping.

The suction area and impeller chambers can be reached by

removing (2) threaded handles (Ref. No. 26) and removing

suction clean out cover plate (Ref. No. 25) and gasket (Ref.

No. 36).

NOTE: When replacing clean out cover plate, carefully wipe

clean all surfaces on which the gasket has contact. Also, make

sure the gasket is in position. The screen in the spark arrester

should be checked.

4-INCH TRASH PUMP

Specications Information and Repair Parts Manual 4S14KLR, 4S13XHR & 4S13XZR

4SXX-251-00 4 6/2023

For Repair Parts contact dealer where pump was purchased.

Please provide following information:

-Model Number

-Serial Number (if any)

Part description and number as shown in parts list

Figure 3 - Repair Parts Illustrations

4-INCH TRASH PUMP

Specications Information and Repair Parts Manual 4S14KLR, 4S13XHR & 4S13XZR

4SXX-251-00 5 6/2023

Repair Parts List

Ref. Part Number for Models:

No. Description 4S14KLR 4S13XHR 4S13XZR Qty.

1 Engine 1632-140-00 1639-031-00 1630-050-00 1

2 Impeller Kit 3945-013-95 3945-015-95 3945-014-95 1

(Includes Ref. Nos. 2, 3, 4 & 5)

3 Shaft Sleeve 1555-143-00 &

Incl. w/Ref 2

1555-143-00 &

Incl. w/Ref 2

1555-143-00 &

Incl. w/Ref 2

4 Shaft Flange Incl. w/Ref 2 N/A N/A 1

5 Impeller Shim Kit 1656-000-90

& Incl. w/Ref 2

1656-000-90

& Incl. w/Ref 2

1656-000-90

& Incl. w/Ref 2

6 Casing Cover Kit 3993-020-96 3993-020-96 3993-022-96 1

(Includes Ref. Nos. 6, 7, 8 & 9)

7 Adapter Incl. w/Ref 6 Incl. w/Ref 6 Incl. w/Ref 6 1

8 Hex Screw Incl. w/Ref 6 Incl. w/Ref 6 Incl. w/Ref 6 6

9 Hex Screw Incl. w/Ref 6 Incl. w/Ref 6 Incl. w/Ref 6 4

10 Wear Plate Kit 2182-004-90 2182-004-90 2182-004-90 1

(Includes Ref. Nos. 10 & 11)

11 Flat Head Screw Incl. w/Ref 10 Incl. w/Ref 10 Incl. w/Ref 10 2

12,13 Seal Assembly-Carbon/SIC/Viton (standard) 1640-163-94 1640-163-94 1640-163-94 1

Seal Assembly-SIC/SIC/Viton (optional) 1640-167-90 1640-167-90 1640-167-90 1

14 Volute Kit 399C-150-95 399C-150-95 399C-150-95 1

(Includes Ref. Nos. 14 & 15)

15 Hex Screw Incl. w/Ref 14 Incl. w/Ref 14 Incl. w/Ref 14 2

16 Check Valve Kit-EPR/EPDM (standard) 399C-076-90 399C-076-90 399C-076-90 1

Check Valve Kit-Buna-N (optional) 1990-005-90 1990-005-90 1990-005-90 1

Check Valve Kit-Viton (optional) 1990-013-90 1990-013-90 1990-013-90 1

(Includes Ref. Nos. 16, 17 & 18)

17 Retainer Pin Incl. w/Ref 16 Incl. w/Ref 16 Incl. w/Ref 16 4

18 Flat Head Screw Incl. w/Ref 16 Incl. w/Ref 16 Incl. w/Ref 16 2

19 Casing Kit 399C-002-96 399C-002-96 399C-002-96 1

(Includes Ref. Nos. 19, 20, 21, 22 & 23)

20 Hex Bolt Incl. w/Ref 19 Incl. w/Ref 19 Incl. w/Ref 19 4

21 Flat Washer Incl. w/Ref 19 Incl. w/Ref 19 Incl. w/Ref 19 8

22 Hex Nut Incl. w/Ref 19 Incl. w/Ref 19 Incl. w/Ref 19 4

23 1/2" NPT Plug Incl. w/Ref 19 Incl. w/Ref 19 Incl. w/Ref 19 1

24 Casing Foot Kit 3993-109-90 3993-109-90 3993-109-90 1

(includes 2 feet and mounting hardware)

25 Clean Out Cover Kit 399C-040-95 399C-040-95 399C-040-95 1

(Includes Ref. Nos. 25 & 26)

26 Handle Stud Incl. w/Ref 25 Incl. w/Ref 25 Incl. w/Ref 25 2

27 Suction Flange Kit 3993-050-95 3993-050-95 3993-050-95 1

(Includes Ref. Nos. 27, 28 & 29)

28 Hex Screw Incl. w/Ref 27 Incl. w/Ref 27 Incl. w/Ref 27 4

29 Lock Washer Incl. w/Ref 27 Incl. w/Ref 27 Incl. w/Ref 27 4

30 Discharge Manifold Kit 3993-080-95 3993-080-95 3993-080-95 1

(Includes Ref. Nos. 30, 31 & 32)

31 Hex Screw Incl. w/Ref 30 Incl. w/Ref 30 Incl. w/Ref 30 4

32 Lock Washer Incl. w/Ref 30 Incl. w/Ref 30 Incl. w/Ref 30 4

33 Fill Plug Kit-EPR/EPDM oring (standard) 3SXE-170-90 3SXE-170-90 3SXE-170-90 1

Fill Plug Kit-Buna-N oring (optional) 3SXB-170-90 3SXB-170-90 3SXB-170-90 1

Fill Plug Kit-Viton oring (optional) 3SXV-170-90 3SXV-170-90 3SXV-170-90 1

(Includes Ref. Nos. 33 & 34)

34 #117 O-ring Incl. w/Ref 33 Incl. w/Ref 33 Incl. w/Ref 33 1

Specications Information and Repair Parts Manual 4S14KLR, 4S13XHR & 4S13XZR

4SXX-251-00 6 6/2023

Ref. Part Number for Models:

No. Description 4S14KLR 4S13XHR 4S13XZR Qty.

KIT Gasket Kit-EPR/EPDM (standard) 3993-301-91 3993-301-91 3993-301-91 1

Gasket Kit-Buna-N (optional) 3993-301-90 3993-301-90 3993-301-90 1

Gasket Kit-Viton (optional) 3993-301-92 3993-301-92 3993-301-92 1

(includes Ref. Nos. 35, 36 & 37)

35 Flange Gasket Incl. w/Ref KIT Incl. w/Ref KIT Incl. w/Ref KIT 2

36 Clean Out Cover Gasket Incl. w/Ref KIT Incl. w/Ref KIT Incl. w/Ref KIT 1

37 #276 O-ring Incl. w/Ref KIT Incl. w/Ref KIT Incl. w/Ref KIT 1

38 Mount hardware kit 3993-107-90 3993-107-90 4S13-100-90 1

(includes raising blocks, bolts, nuts & washers)

39 Suction Strainer 1681-001-00 1681-001-00 1681-001-00 1

40 Roll Frame C401-100-00 C401-100-00 C401-100-00 1

41 Rubber Foot Kit C400-100-91 C400-100-91 C400-100-91 1

(includes Ref. Nos. 41, 42 and 43)

42 Hex Bolt Incl. w/Ref 41 Incl. w/Ref 41 Incl. w/Ref 41 4

43 Hex Nut Incl. w/Ref 41 Incl. w/Ref 41 Incl. w/Ref 41 4

44 Battery Tray Kit 1696-101-91 1696-101-91 1696-101-91 1

(includes Ref. Nos. 44, 45, 46, 47, 48 & 49)

45 J-Bolt Incl. w/Ref 44 Incl. w/Ref 44 Incl. w/Ref 44 2

46 Battery Hold Bown Incl. w/Ref 44 Incl. w/Ref 44 Incl. w/Ref 44 1

47 Wing Nut Incl. w/Ref 44 Incl. w/Ref 44 Incl. w/Ref 44 2

48 Hex Bolt Incl. w/Ref 44 Incl. w/Ref 44 Incl. w/Ref 44 2

49 Hex Nut Incl. w/Ref 44 Incl. w/Ref 44 Incl. w/Ref 44 2

‡ Battery Cable Assembly (12" Black) C401-104-90 C401-104-90 C401-104-90 1

‡ Battery Cable Assembly (30" Red) C401-105-90 C401-105-90 C401-105-90 1

(‡) Not Shown

Repair Parts List - CONTINUED

Specications Information and Repair Parts Manual 4S14KLR, 4S13XHR & 4S13XZR

4SXX-251-00 7 6/2023

NOTES:

Specications Information and Repair Parts Manual 4S14KLR, 4S13XHR & 4S13XZR

4SXX-251-00 8 6/2023

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere AMT Pumps Wasserpumpe Handbücher

AMT Pumps

AMT Pumps 3270 Montageanleitung

AMT Pumps

AMT Pumps 3150 Montageanleitung

AMT Pumps

AMT Pumps 3160-99 Montageanleitung

AMT Pumps

AMT Pumps 3931-99 Montageanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung