AMT Crono S-PID 30 Betriebsanleitung

Crono S-PID 30

Short Programming Guide - Flow Mode (mL/hr)

Pump activation and mode selection

The default delivery setting for the S-PID 30 is timed mode. This allows

programming of the duration of infusion. To change the mode of operation

remove and then replace the battery.

The pump will perform a short self test procedure during which a full screen

display of all elements should appear.

When the symbol [-t-] is displayed, press and hold the [P] button until the

display flashes. Press the [-] button until the display changes to [-F-]. Press

[P] to confirm and the pump will switch to [OFF] mode.

.Locking/unlocking the keypad

By default keyboard lock is not activated on this device.

With the pump displaying [OFF] press the (-) key for approximately 7

seconds. A number representing the number of completed infusions will

appear on the screen.

While still holding the [-] key depress the [+] key.The screen will display

flashing [L.0] and the keyboard is unlocked.

Use the (+) or (-) button to select required value. (L1 is on, L0 is off)

Caution: Users must familiarise themselves with the full user instructions.

These notes provide only a reminder of main functions.

This symbol will display when the keyboard is locked.

SG008/19BM

Start the infusion by pressing the [+/ON] button.

You are given the option to prime the infusion set [Pr]. Press and hold

the [P] button to deliver the required prime up to a maximum of 1.5mL.

Press the [+] button again to start the infusion at any time.

To change the infusion rate press the [+] button to display the current

flow rate . Press the [-] key until the screen symbols flash, and then

press the [+] button to increase, or the [-] button to reduce, the infusion

rate.

After 5 seconds this will be locked into the pump memory.

At the end of an infusion the plunger will automatically return to its

programmed start position

To return the plunger earlier, switch the pump into [StoP] mode by

pressing the [+] and [-] keys together. Then press the [P]and [-]

buttons together until [END] appears on the screen.

The syringe rubber plunger will not be withdrawn with this procedure.

With the keyboard unlocked, and the pump displaying [OFF] pressing

the [P] button will allow you to step through a menu to set the following

parameters in turn.

End of infusion alarm On/Off

Syringe Partial Volume 1ml steps

Press the [P] button to select alarm setting.

Use the (+) to set alarm on or (-) button to set alarm off

Press the [P] button to confirm value and select the partial volume

setting.

Press [-] button to reduce the volume or [+] button to increase.

Press the [P] button to confirm value and the pump will take a short

time to position the plunger at the programmed position.

Starting infusion and setting infusion time

Resetting plunger position

Programming the pump

Setting procedure

Inhaltsverzeichnis

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung