Analog Devices EVAL-ADPD6000 Bedienungsanleitung
User Guide | EVAL-ADPD6000
UG-2033
Evaluating the ADPD6000 Multimodal Sensor Front End
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS. Rev. 0 | 1 of 20
FEATURES
►Board supports ADPD6000 population
►4 separately driven LEDs included: 1 green LED at the center, 1
red LED, and 2 infrared LEDs
►Four channels of PD input: two channels with single PD, and two
channels with double PD
►Works with the VSM Client evaluation software allowing
►Time domain graphing and logging
►Selection of supported functions, including PPG, BIA, and
ECG
►Real-time data display with the various combinations of the
functions
EVALUATION KIT CONTENTS
►EVAL-ADPD6000Z evaluation board
►EVAL-VSMUCZ microcontroller board
ADDITIONAL EQUIPMENT NEEDED
►USB to Type-C cable
►3.7 V battery
►Electrode board
►Soft cable to connect EVAL-ADPD6000Z and EVAL-VSMUCZ
►Wrist strap
ONLINE RESOURCES
►ADPD6000 data sheet
►VSM Client software (available on EVAL-ADPD6000 product
page)
GENERAL DESCRIPTION
This user guide describes the operation of the EVAL-ADPD6000Z
demonstration kit, which is an evaluation module for the
ADPD6000.
The ADPD6000 is a fully integrated analog front end (AFE) for
wearable vital signal monitoring (VSM) devices. The key functions
of the ADPD6000 include photoplethysmography (PPG), electrocar-
diography (ECG), and body impedance analysis (BIA).
The demonstration kit includes both software and hardware. The
EVAL-ADPD6000Z can evaluate the AFE feature and verify the
system design based on the AFE. According to the requirements of
the application, the user can use a cable connection or Bluetooth
connection to establish communication between the PC and the
EVAL-ADPD6000Z.
This user guide also describes the example configuration of the
different functions of the ADPD6000.
For full details on the ADPD6000, see the ADPD6000 data sheet,
which must be consulted in conjunction with this user guide when
using the EVAL-ADPD6000Z.
EVALUATION BOARD PHOTOGRAPH
Figure 1. EVAL-ADPD6000Z
User Guide EVAL-ADPD6000
TABLE OF CONTENTS
analog.com Rev. 0 | 2 of 20
Features................................................................ 1
Evaluation Kit Contents......................................... 1
Additional Equipment Needed............................... 1
Online Resources.................................................. 1
General Description...............................................1
Evaluation Board Photograph................................1
Preparation and Setup...........................................3
EVAL-ADPD6000Z Components........................3
PCB Connection.................................................3
Software Installation.............................................. 5
Power on the System............................................ 6
Power On–Cable Connection.............................6
Power On–Bluetooth Connection.......................6
Add Device via Bluetooth................................... 6
VSM Client ............................................................8
Find the Device On VSM Client .........................8
Configure the Device........................................10
Receive the Data.............................................. 11
Human Measurement.......................................... 13
PPG Measurement...........................................13
ECG Measurement...........................................13
BIA Measurement.............................................14
Evaluation Board Schematics and Artwork......... 15
Notes................................................................... 20
REVISION HISTORY
4/2022—Revision 0: Initial Version
User Guide EVAL-ADPD6000
PREPARATION AND SETUP
analog.com Rev. 0 | 3 of 20
EVAL-ADPD6000Z COMPONENTS
Figure 2 shows the components needed for evaluation.
Figure 2. EVAL-ADPD6000Z Demonstration Kit Components
PCB CONNECTION
Take the following steps to establish the printed circuit board (PCB)
connection:
1. Connect the battery to the connector on the EVAL-VSMUCZ
(see Figure 3. Ensure that the S1 switch is off.
Figure 3. Battery Connected to EVAL-VSMUCZ
2. Connect the EVAL-VSMUCZ to the EVAL-ADPD6000Z (see
Figure 4 and Figure 5). Ensure the EVAL-VSMUCZ and EVAL-
ADPD6000Z have the same number of pins, and that the pin
numbers match.
Figure 4. EVAL-VSMUCZ Connection
Figure 5. EVAL-ADPD6000 Connection
3. For ECG or BIA measurement, connect the EVAL-ADPD6000Z
to the electrodes on the electrode board as follows:
►For ECG measurement, connect P3 to Electrode 1, P4 to
Electrode 2, and P6 to Electrode 3. Leave Electrode 4
unconnected (see Figure 6).
►For BIA measurement, connect P3 to Electrode 1, P4 to
Electrode 2, P6 to Electrode 3, and P5 to Electrode 4 (see
Figure 7).
Note that the BIA connection can also be used for ECG meas-
urement.
User Guide EVAL-ADPD6000
SOFTWARE INSTALLATION
analog.com Rev. 0 | 5 of 20
The VSM Client software is the graphical user interface (GUI)
used for the EVAL-ADPD6000Z demonstration kit. The VSM Client
software is available on the EVAL-ADPD6000Z product page.
Take the following steps to install VSM Client:
1. Download and launch the VSM Client installer.
2. Read the software license agreement and click I Agree (see
Figure 9).
Figure 9. License Agreement
3. Select Only for me and click Next > (see Figure 10). Do not
select Anyone who uses this computer (all users), as this
option can cause the installation to suspend or fail.
Figure 10. Choose Installation Options
4. Click Browse... to choose the installation location and then click
Next > (see Figure 11).
Figure 11. Choose Installation Location
5. When the installation is complete, click Finish to complete the
installation process (see Figure 12).
Figure 12. Installation Complete
User Guide EVAL-ADPD6000
POWER ON THE SYSTEM
analog.com Rev. 0 | 6 of 20
After preparing the hardware and installing the software, the EVAL-
ADPD6000Z is ready to power on.
POWER ON–CABLE CONNECTION
Connect the USB to Type-C cable from the PC to J5 on the
EVAL-VSMUCZ to power on the EVAL-VSMUCZ automatically. The
two indicator lights on the EVAL-VSMUCZ (DS1 and DS4) turn on.
If the S1 switch labeled in Figure 13 is set to on, the battery is
charged by the PC. Figure 13 shows the cable connection.
Figure 13. Cable Connection
POWER ON–BLUETOOTH CONNECTION
Take the following steps to power on the system without the USB
cable:
1. On the EVAL-VSMUCZ, set the S1 switch labeled in Figure 13
to on. The standalone DS1 indicator LED labeled in Figure 13
turns on.
2. Press (for about two seconds) the S3 button on the EVAL-
VSMUCZ to power on the system. The two indicator lights on
the EVAL-VSMUCZ (DS1 and DS4) turn on.
ADD DEVICE VIA BLUETOOTH
Take the following steps to add the EVAL-VSMUCZ via Bluetooth
(these steps are shown using Windows® 10):
1. Click the Bluetooth Devices icon in the system tray and select
Add a Bluetooth Device (see Figure 14).
Figure 14. Add a Bluetooth Device
2. The Settings window opens (see Figure 15). Under Bluetooth
& other devices, click Add Bluetooth or other device.
Figure 15. Add Bluetooth Device from Settings Window
3. The Add a device window opens (see Figure 16). Select
Bluetooth.
User Guide EVAL-ADPD6000
POWER ON THE SYSTEM
analog.com Rev. 0 | 7 of 20
Figure 16. Choose Bluetooth Device Type
4. Select the EVAL-VSMUCZ from the list of devices (in this
example, Figure 17 shows the device as B8-7425A2). The
device is now connected (see Figure 18).
Figure 17. Select EVAL-VSMUCZ
Figure 18. Device Connected
After adding the EVAL-VSMUCZ, two Bluetooth serial ports appear
in the Device Manager window: Standard Serial over Bluetooth
link (COM10) and Standard Serial over Bluetooth link (COM11)
(see Figure 19). The user selects one of these two ports in the VSM
Client software.
Figure 19. Device Manager
User Guide EVAL-ADPD6000
VSM CLIENT
analog.com Rev. 0 | 8 of 20
FIND THE DEVICE ON VSM CLIENT
Take the following steps to find the device on the VSM Client
software:
1. After installing VSM Client, power on the EVAL-ADPD6000Z
and launch VSM Client.
2. Click Click to connect in the start interface of VSM Client (see
Figure 20).
Figure 20. Start Interface of VSM Client
3. In the Hardware Connection pane, select the communication
(COM) port according to the connection method, as follows:
►If using a Bluetooth connection, two ports are available. In
the example shown in Figure 21, these ports are COM50
Microsoft BTHENUM and COM58 Microsoft BTHENUM.
Select one of the two ports. If the following steps cannot
be completed successfully with the selected port, select a
different port.
►If using a cable connection, only one port is available (see
Figure 22). In the example shown in Figure 22, the port is
COM11 Microsoft USB.
The COM serial port numbers shown are examples only. Refer
to the Device Manager for the COM serial port numbers.
Figure 21. Bluetooth Connection COM Ports
Figure 22. Cable Connection COM Port
4. Toggle the connection switch to Connect (see Figure 23).
When connected, a Success to connect target! pop-up ap-
pears at the top of the VSM Client window (see Figure 24), and
the Click to connect button changes to display Connected
6000. To disconnect the device, toggle the connection switch to
Disconnect. The following pop-up messages can appear if the
connection is unsuccessful:
►Failed to connect target: undefined. Please try to recon-
nect. If this pop-up appears (see Figure 25), select another
COM port and reconnect.
►Fail to get firmware version!. If this pop-up appears (see
Figure 26), the firmware version may not match the software
version. Update the firmware in the kit. For details on updat-
ing the firmware, see the EVAL-ADPD6000Z product page.
Figure 23. Toggle Connection Switch
Figure 24. Connection Successful
Figure 25. Failed to Connect Target Error
Figure 26. Failed to Get Firmware Version Error
5. From the Type dropdown menu, select one of three functions:
ECG, PPG, or BIOZ (see Figure 27). Click Select to enter the
configuration interface.
User Guide EVAL-ADPD6000
VSM CLIENT
analog.com Rev. 0 | 10 of 20
CONFIGURE THE DEVICE
Take the following steps to configure the device:
1. Click Load cfg File in the configuration interface of VSM Client
to load a basic configuration file (see Figure 28). To export the
current configuration file, click Export cfg File to save the script
in the configuration file folder (see Figure 30). To change the
loaded .dcfg file, click Reset before continuing.
Figure 28. Configuration Interface
2. Click Click/Drag a .dcfg file to load to open the .dcfg file in
the Load Configuration window (see Figure 29). According
to the application or measurement conditions, the user can
choose the following initial configurations from the C:\Analog
Devices\VSM Client\VSM_Client\Cfg\ADPD6000 location:
►ADPD6000_BIOZ_slotABCDEF_MS6_Testing: BIA magni-
tude and phase measurement
►ADPD6000_ECG_Testing: ECG channel signal measure-
ment
►ADPD6000_PPG_Testing_slotA_Peak_SNR_one_led: PPG
peak signal-to-noise (SNR) test using LED1A
►ADPD6000_PPG_Testing_slotA_Peak_SNR_two_led: PPG
peak SNR test using LED1A and LED2A
►ADPD6000_PPG_Testing_slotA_SNR_85dB: PPG 85 dB
SNR test using LED2A
►ADPD6000_PPG_Testing_slotA_SNR_95dB: PPG 95dB
SNR test using LED1A
The configuration files in the configuration file folder may differ
from those shown in Figure 30.
Figure 29. Choose Configuration File
Figure 30. Configuration File Folder
3. Click Load (see Figure 31) to load the configuration file.
Figure 31. Load Configuration
4. After loading the configuration file, the Highlevel Configura-
tion tab shows the current device data (see Figure 32). This
tab shows the most used controls, which can be configured. To
reset the data, click Reset.
Figure 32. Highlevel Configuration Tab
5. To read or write an individual register, click the Register Con-
figuration tab. To check a register, enter the address in the
Register Address field and click Read (see Figure 33). To
change a register, enter the value in the Register Value field
and click Write (see Figure 34). See the ADPD6000 data sheet
for the detailed values of the registers.
Inhaltsverzeichnis
Andere Analog Devices Computerhardware Handbücher
Analog Devices
Analog Devices EVAL-ADF4152HVEB1Z Bedienungsanleitung
Analog Devices
Analog Devices ADSP-SC573 EZ-KIT Bedienungsanleitung
Analog Devices
Analog Devices ADRV902 Series Bedienungsanleitung
Analog Devices
Analog Devices ADSP-21369 EZ-KIT Lite Bedienungsanleitung
Analog Devices
Analog Devices MAX77831 Bedienungsanleitung
Analog Devices
Analog Devices ADSST-EM-3040 Bedienungsanleitung
Analog Devices
Analog Devices Linear SCP-LT8362-S-EVALZ Kurzanleitung zur Einrichtung
Analog Devices
Analog Devices ADSP-2186 Bedienungsanleitung
Analog Devices
Analog Devices LINEAR DC2672A-A Kurzanleitung zur Einrichtung
Analog Devices
Analog Devices Linear Technology LTC6953 Kurzanleitung zur Einrichtung
Analog Devices
Analog Devices ADSP-SC58 Series Anwendungshandbuch
Analog Devices
Analog Devices SHARC ADSP-21065L Bedienungsanleitung
Analog Devices
Analog Devices TigerSHARC ADSP-TS201S Bedienungsanleitung
Analog Devices
Analog Devices AD73360L Bedienungsanleitung
Analog Devices
Analog Devices EVAL-ADPA1106 Bedienungsanleitung
Analog Devices
Analog Devices ADAV4622 Bedienungsanleitung
Analog Devices
Analog Devices MICROCONVERTER ADUC812 Bedienungsanleitung
Analog Devices
Analog Devices EZ-KIT LITE ADSP-2191 Bedienungsanleitung
Analog Devices
Analog Devices ADSP-BF53x EZ-Extender 1 Bedienungsanleitung
Analog Devices
Analog Devices Blackfin Audio EZ-Extender Bedienungsanleitung
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
