Analog Devices ADL5580-EVALZ Bedienungsanleitung

ADL5580-EVALZ Evaluation Board User Guide

UG-1847

One Technology Way •P. O. Box 9106 •Norwood, MA 02062-9106, U.S.A. •Tel: 781.329.4700 •Fax: 781.461.3113 •www.analog.com

Evaluating the ADL5580 Fully Differential, 10 GHz ADC Driver with 10 dB Gain

PLEASE SEE THE LAST PAGE FOR AN IMPORTANT

WARNING AND LEGAL TERMS AND CONDITIONS.Rev. 0 | Page 1 of 14

FEATURES

Full featured evaluation board for the ADL5580

Dual-supply operation

Easy to use interface with ACE

EQUIPMENT NEEDED

+5 V and −1.8 V dc power supplies

System demonstration platform, EVAL-SDP-CS1Z (SDP-S)

Network analyzer

Signal generator

Oscilloscope with high-Z probe (option)

Spectrum analyzer (option)

Windows PC with two or more USB ports

DOCUMENTS NEEDED

ADL5580 data sheet

ADL5580-EVALZ user guide

SOFTWARE NEEDED

ACE software

GENERAL DESCRIPTION

The ADL5580-EVALZ evaluation board allows the manual control

of the ADL5580 through the USB port on a Windows® PC via a

SDP-S interface board.

Additional information on the ADL5580 is provided in the

ADL5580 data sheet. Consult the ADL5580 data sheet in

conjunction with this user guide when using the ADL5880-

EVALZ evaluation board.

EVALUATION BOARD PHOTOGRAPHS

24575-009

Figure 1. ADL5580-EVALZ, Top

24575-010

Figure 2. ADL5580-EVALZ, Bottom

Downloaded from Arrow.com.

UG-1847 ADL5580-EVALZ Evaluation Board User Guide

Rev. 0 | Page 2 of 14

TABLE OF CONTENTS

Features .............................................................................................. 1

Equipment Needed........................................................................... 1

Documents Needed.......................................................................... 1

Software Needed ............................................................................... 1

General Description......................................................................... 1

Evaluation Board Photographs....................................................... 1

Revision History ............................................................................... 2

Evaluation Board Hardware............................................................ 3

Hardware Setup ............................................................................ 3

Evaluation Board Software Quick Start Procedures.....................5

Installing the ACE Software and ADL5580 Plug-Ins ...............5

Single-Tone Demonstration with ACE ......................................5

Using the ADL5580-EVALZ Evaluation Board.............................8

Losses and Signal-to-Noise Ratio (SNR) Degradation ............8

ACE Macro Tools ..........................................................................9

Evaluation Board Schematics........................................................ 11

Bill of Materials........................................................................... 13

REVISION HISTORY

12/2020—Revision 0: Initial Version

Downloaded from Arrow.com.Downloaded from Arrow.com.

ADL5580-EVALZ Evaluation Board User Guide UG-1847

Rev. 0 | Page 3 of 14

EVALUATION BOARD HARDWARE

HARDWARE SETUP

The hardware is connected as shown in Figure 3. To power up the

ADL5580-EVA L Z , use a +5 V and −1.8 V, 300 mA dc power

supply. Connect the SDP-S to the PC through a USB cable.

OUTIN

POWER

24575-001

USB

DUT

Figure 3. ADL5580-EVALZ USB and SDP-S Connections

See Table 1 and Table 2 to connect the equipment needed to

evaluate the ADL5580-E VA L Z .

Table 1. ADL5580-EVALZ Connections

Equipment Connection

Power Supply P3: Pin 1 (−1.8 V), Pin 2 (GND),

and Pin 3 (+5 V)

Signal Source J1 (VINP) and J2 (VINM)

Network Analyzer Connect to two ports on the

four port network analyzer

(see Figure 4)

Signal Generator (Option) Set the source to a 100 MHz

frequency with an output level

of −20 dBm (see Figure 5)

Baluns

1:2 Connect to the differential

inputs (J1 and J2) of the

ADL5580-EVALZ

2:1 Connect to the differential

outputs (J3 and J4) of the

ADL5580-EVALZ

SDP-S P4

Signal Analyzer J3 (VOUTP) and J4 (VOUTM)

Network Analyzer Connect two ports on the four

port network analyzer (see

Figure 4)

Spectrum Analyzer (Option) Connect to port through a 2:1

balun (see Figure 5)

Oscilloscope (Option) Measure the voltage levels

directly at the ADL5580 pins

using a high-Z probe

Table 2. SDP-S Connections

Equipment Connection

PC USB Cable J2

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

UG-1847 ADL5580-EVALZ Evaluation Board User Guide

Rev. 0 | Page 4 of 14

COM

+–

POWER SUPPLY

NETWORK

ANALYZER

USB

–1.8V

RF OUTPUTRF INPUT

GND+5.0V

24575-011

Figure 4. ADL5580-EVALZ Connection Diagram

RF OUTPUTRF INPUT

SPECTRUM ANALYZER

SIGNALGENERATOR

USB

COM

+–

POWER SUPPLY

1:2 BALUN 2:1 BALUN

–1.8VGND+5.0V

24575-012

Figure 5. ADL5580-EVALZ Measurement Setup (Option)

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

ADL5580-EVALZ Evaluation Board User Guide UG-1847

Rev. 0 | Page 5 of 14

EVALUATION BOARD SOFTWARE QUICK START PROCEDURES

INSTALLING THE ACE SOFTWARE AND ADL5580

PLUG-INS

The ADL5580-EVALZ evaluation board connects to the SDP-S

for quick evaluation of the ADL5580. The ADL5580-EVALZ is

configured over the USB from a panel within the ACE software,

which can be downloaded from the ACE software page. When

the ACE software installation is complete, the user must install

the ACE Evaluation Board Plug-ins that are provided with the

evaluation package to the hard drive of the PC.

Double-click the Board.ADL5580.1.2019.22300.acezip file to

install the evaluation board plug-ins.

Ensure that the Board.ADL5580.1.2019.22300 and Chip.

ADL5580.1.2019.22300 folders are located in the

C:\ProgramData\Analog Devices\ACE\Plugins folder.

SINGLE-TONE DEMONSTRATION WITH ACE

Use the following settings to configure the ADL5580 to amplify

a 100 MHz sine wave using the ACE software:

•Configure the hardware according to the Hardware Setup

section and what is shown in Figure 5.

•Set the frequency of the signal generator to 100 MHz and

the output level to −20 dBm. Optionally, connect the

spectrum analyzer to the J3 and J4 connectors using an

external balun (for example, the HYPERLABS 2:1 balun

was used).

•Set RF off state.

•Use 2.92 mm, 40 GHz, female Southwest Microwave

connectors at J1, J2, J3, and J4 on the ADL5580-EVALZ.

Connect these connectors to the Subminiature Version A

(SMA), 3.5 mm connector with care. However, it is

suggested to use a 2.92 mm, SMA adaptor to avoid any

potential damage.

•Power up the ADL5580-EVA L Z .

•Launch the ACE application. This action displays the

initial ACE start page as shown in Figure 6. The ADL5580-

EVALZ is detected automatically and displays under

Attached Hardware.

•Click the ADL5580-E VA L Z icon to open the evaluation

board level view shown in Figure 7. Because the ADL5580-

EVALZ is a simple evaluation board, only the ADL5580

represents as a controllable component.

•Click the ADL5580 icon to open the IC level view as

shown in Figure 8.

•Configure the ADL5580 in the ChipView (see Figure 7) as

follows:

•Select the Pin 19 check box to select EN.

•Ensure that the Enable Ref and the Enable Amp

check boxes are selected. Enable Ref enables the

internal voltage, and Enable Amp enables the

amplifier section (see Figure 8).

•Under the Input Termination Mode dropdown

menu, select Internal VCM Enabled, VCMI Pin

Disconnected (see Figure 8).

•Under the Output Termination Mode dropdown

menu, select Internal VCM Enabled, VCMO Pin

Disconnected (see Figure 8).

•Set C Peak (defaults to 3), if necessary (see Figure 8).

•Set Input CM Voltageand Output CM Voltage, if

necessary (see Figure 8).

•Click Apply Changes for the changes to take effect (see

Figure 8). Repeat the previous step to enable or disable the

ADL5580-EVA LZ with the hardware enabled.

•Set RF on state at the signal generator.

•With the signal generator set to an output level of −20 dBm,

the power gain is 13 dB at 1 GHz. However, note that this

value is affected by cabling and balun losses on the signal

path.

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

UG-1847 ADL5580-EVALZ Evaluation Board User Guide

Rev. 0 | Page 6 of 14

24575-002

Figure 6. Initial ACE Start Page

24575-003

Figure 7. ADL5580-EVALZ Board Level View

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

ADL5580-EVALZ Evaluation Board User Guide UG-1847

Rev. 0 | Page 7 of 14

24575-004

Figure 8. ADL5580 IC Level View

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

UG-1847 ADL5580-EVALZ Evaluation Board User Guide

Rev. 0 | Page 8 of 14

USING THE ADL5580-EVALZ EVALUATION BOARD

LOSSES AND SIGNAL-TO-NOISE RATIO (SNR)

DEGRADATION

The ADL5580 provides a nominal 10 dB of voltage gain defined

between the input and output pins, which translates to a power

gain of 13 dB because the input impedance is twice the output

impedance. The resistive impedance matching converts the

50 Ω differential output to a more common 100 Ω. However,

this resistive impedance matching adds 7.7 dB of attenuation

that must be considered. The miscellaneous components of the

ADL5580-EVALZ can add to the signal losses and degrade the SNR

as well.

10dB

VOLTAGE GAIN 7.7dB

POWER ATTENUATION

IN OUT

100Ω

DIFFERENTIAL

100Ω

DIFFERENTIAL50Ω

DIFFERENTIALIMPEDANCE

MATCH

24575-005

Figure 9. Losses and SNR Degradation

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

ADL5580-EVALZ Evaluation Board User Guide UG-1847

Rev. 0 | Page 9 of 14

ACE MACRO TOOLS

ACE also contains Macro Tools that can record register reads and

writes. Use the Installation Wizard or click Proceed to Memory

Map to use these tools. To use the M a cr o To o l s , select the Record

Sub-Commands checkbox and click the Record button (see

Figure 10). Changes in the memory map remain bolded until these

changes are applied to the device. The changes are also recorded as

user interface (UI) commands by the Macro Tools once the

changes are made. Changed register write commands for the

controls are also recorded. Click Apply Changes to execute the

commands and make changes to the memory map. To stop

recording, click the Stop Recording button. A M a cr o To o lspage

with the command steps is then created. The macro can be saved

using the Save Macro button so that the macro can be loaded

for future use.

The raw macro file is saved using ACE syntax, which is

not easily readable. To remedy this, the ACE software download

includes an ACE Macro/Hex Converter tool (see Figure 11). The

user can choose to include or exclude register write, reads, and/or

comments in the conversion. The file pathways for the source

and save paths are the same, except the source is an .acemacro

file, and the save is a .txt file. The Convert button (see Figure 11)

converts the macro to hex, which is easier to read, and the

conversion tool can also convert .txt files back to .acemacro files,

if desired.

24575-006

Figure 10. ACE Macro Tools

UG-1847 ADL5580-EVALZ Evaluation Board User Guide

Rev. 0 | Page 10 of 14

24575-007

Figure 11. Conversion Set Up for Macro to Hex

24575-008

Figure 12. Converted Text File

Inhaltsverzeichnis

Andere Analog Devices Hauptplatine Handbücher

Analog Devices

Analog Devices ADP151 Bedienungsanleitung

Analog Devices

Analog Devices LINEAR DC2702A-A Kurzanleitung zur Einrichtung

Analog Devices

Analog Devices EVAL-AD5753SDZ Bedienungsanleitung

Analog Devices

Analog Devices EV-ADA4571RSDZ Bedienungsanleitung

Analog Devices

Analog Devices ADSP-21992 EZ-KIT LITE Benutzerhandbuch

Analog Devices

Analog Devices EVAL-ADUCM300QSPZ Bedienungsanleitung

Analog Devices

Analog Devices Blackfin Landscape LCD EZ-Extender... Bedienungsanleitung

Analog Devices

Analog Devices AD911 Series Bedienungsanleitung

Analog Devices

Analog Devices EVAL-SSM3582Z Bedienungsanleitung

Analog Devices

Analog Devices EVAL-SSM3525Z Bedienungsanleitung

Analog Devices

Analog Devices AD7780 Bedienungsanleitung

Analog Devices

Analog Devices EVAL-LTC9101-3 Bedienungsanleitung

Analog Devices

Analog Devices AD7273 Bedienungsanleitung

Analog Devices

Analog Devices ADSP-2189M EZ-KIT Lite Bedienungsanleitung

Analog Devices

Analog Devices DC336 Bedienungsanleitung

Analog Devices

Analog Devices AD9574 Kurzanleitung

Analog Devices

Analog Devices EV-TEMPSENSE-ARDZ Bedienungsanleitung

Analog Devices

Analog Devices EVAL-AD1974AZ Bedienungsanleitung

Analog Devices

Analog Devices EZ-KIT Lite ADSP-BF537 Bedienungsanleitung

Analog Devices

Analog Devices UG-059 Bedienungsanleitung

Analog Devices

Analog Devices EVAL-AD7276SDZ Bedienungsanleitung

Analog Devices

Analog Devices AD9783 Bedienungsanleitung

Analog Devices

Analog Devices SCP-LT8604C-BEVALZ Kurzanleitung zur Einrichtung

Analog Devices

Analog Devices EVAL-ADAU1850 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung