Analytic Systems BCA1505MW-24 Bedienungsanleitung

INSTALLATION &

OPERATION MANUAL

BCA1505MW-24

Battery Charger

8128 River Way, Delta B.C. V4G 1K5 Canada T. 604.946.9981 F. 604.946.9983 TF. 800.668.3884 (US/CANADA)

www.analyticsystems.com

An ISO9001 and AS9100 Registered Company Battery Chargers •Inverters •Power Supplies •Voltage Converters

Revised - May 18, 2016

IMPORTANT & SAFETY INSTRUCTIONS

1. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating

instructions for power supply.

2. Do not expose power supply to rain or snow.

3. Use of an attachment not recommended or sold by the power supply manufacturer may

result in a risk of re, electric shock, or injury to persons.

4. Do not disassemble power supply; take it to a qualied serviceman when service or

repair is required. Incorrect reassembly may result in a risk of electric shock or re.

5. To reduce risk of electric shock, unplug power supply from outlet before attempting any

maintenance or cleaning. Turning off controls will not reduce this risk.

6. Never place marine power supply directly above battery; gases from battery will corrode

and damage power supply.

7. Never allow battery acid to drip on power supply when reading gravity or lling battery.

8. O/P CONNECTION PRECAUTIONS

Connect and disconnect DC output connections only after setting the power supply

switch to the off position.

GROUNDING AND AC POWER CORD CONNECTION INSTRUCTIONS — The plug must be

plugged into an outlet that is properly installed and grounded in accordance with al local

codes and ordinances.

DANGER — Never alter AC cord or plug provided — if it will not t outlet, have proper

cord installed by a qualied electrician. Improper connection can result in a risk of an electric

shock.

Analytic Systems does not recommend the use of the BCA1505MW-24 Series Power Supplies

in life support applications where failure or malfunction of this product can be reasonably

expected to cause failure of the life support device or to signicantly affect its safety or

effectiveness. Analytic Systems does not recommend the use of any of its products in direct

patient care.

Examples of devices considered to be life support devices are neonatal oxygen analyzers,

nerve stimulators (whether used for anesthesia, pain relief, or other purposes), autotransfusion

devices, blood pumps, debrillators, arrhythmia detectors and alarms, pacemakers,

hemodialysis systems, peritoneal dialysis systems, neonatal ventilator incubators, ventilators

for both adults and infants, anesthesia ventilators, and infusion pumps as well as any other

devices designated as “critical” by the U.S. FDA.

Introduction

All new Current Mode switching design offers increased power and reliability in a compact

package. Extra input and output ltering reduce EMI to extremely low levels. Reliability

features include an input fuse, thermal shutdown, current limiting and output short circuit

shutdown with automatic recovery. The model BCA1505MW-24 Power Supply supplies 24

VDC from a 110 or 220 VAC power source.

Input Voltages

Nominal (ip) Auto Select 110/220

Actual 90-130Vac/180-260Vac

Input Amps (max) 14A

Input Breaker 25 A Breaker

Specications

This unit comes with a carrying handle. The unit complies with the IP66 Standard.

In a DC UPS ( Un-interruptible Power Supply ) , the charger simultaneously powers the DC load

as well as the battery. As long as the AC power to the charger is available and the charger is

working normally, the charger will supply the DC load as well as charge / oat the battery. In

case the AC power fails or if the charger stops working, the battery will automatically power

the DC load. As soon as the AC power to the charger is restored, the DC load will once again

be fed by the charger and at the same time the battery will be recharged.

CAUTION! Please ensure that the sum of the current drawn by the DC load and the current

desired for charging the battery is less than the maximum current capacity of the charger. To

use as a DC UPS, rst switch off the DC load and connect it to the battery. Now connect the

battery. Switch on the charger and then switch on the DC load.

Features

General

Input Frequency 45 - 65 Hz

Noise on Input < 50 milli-Volts

Noise on Output < 50 milli-Volts

Transient Response < 1 V for 50% surge

Efciency > 80 % @ maximum output

Temp. Range -40 to +50 deg. C @ maximum output

Isolation Input-Output & Input-Case 1500 Vdc

Output-Case 500 VDC

Mechanical Specications

Length 21.5 in / 54.61cm (with connectors on)

Width 9.5 in / 24.13 cm

Height 5.5 in / 13.97 cm

Clearance 4 Inch (2.5 cm) all around

Material Marine Grade Aluminum

Finish Black anodized

Fastenings 18-8 Stainless

Weight 21 lb / 9.5 kg

Safety ABS 11-HS794404E-PDA

Designed and manufactured by: ANALYTIC SYSTEMS WARE (1993) LTD.

8128 River Way, Delta, BC V4G 1K5

Canada

p. 604.946.9981 f. 604.946.9983 tf. 800.668.3884 US/Canada

www.analyticsystems.com [email protected]

* Specications subjects to change without notice.

Output Voltages

Nominal (op) 24Vdc

Float (Vdc) 27.2 ± 0.05

Absorption Voltage (Vdc) 28.8

Charging Amps 35A

Absorption to Float (Amp) 5.2A

Battery Banks 1

Equalize Voltage (Vdc) 31

Temperature Compensation Coefcient -60mV/°C

Battery Size (Amp Hours)* 200-300

Output Crowbar 34.0 ± 1.0 V

Adjust ± 1.0 Vdc

Installation

MOUNTING

Mount the unit and allow at least 4 inches of clearance around the heat sink ns for adequate

cooling.

POWER CONNECTION

The unit is supplied with power leads about 8 feet long. This should normally be adequate to

connect to a source of power. If you must extend the power leads, be sure to use at least a

good quality (typeTEW) AWG 8 gauge wire. The wire colours are:

Operation

Once you have decided on the charging prole you must set the switch to the correct

position. Set the switch to the correct position as shown on the label.

To turn the unit on, simply move the power switch to the ON position. The alarm buzzer will

sound and the Low Output LED will come on briey, and then the green OUTPUT ON LED will

illuminate.

When the unit is rst turned on, it will charge the batteries at a constant current and

the charging light will be on. After a period of time, which may be minutes to hours, the

batteries will reach the oat voltage at which time the charging light will go off, and the

charging current will reduce as necessary to maintain the batteries at that voltage. You may

check this voltage at the output terminals of the unit with a good digital voltmeter.

110 VAC

Black/Brown - AC Hot

White/Blue - AC Neutral

Green - Ground

All connections should be made inside an appropriate junction box. The maximum current

draw from the 110 VAC supply is 14 amps, so a 20 amp circuit breaker should be used in the

circuit panel.

The unit is supplied with two AWG 8 gauge wires. The red wire is the output positive. The

black wire is the output negative.

Output Connection

This charger features user selectable 2 or 3 stage charging. The charging prole is selected by

turning the switch on the front panel to 3 stage or 2 stage charging.

A two-stage charger provides a constant current until the battery reaches its rated capacity

and then switches to a “oat” voltage. The current then reduces as necessary to maintain

the battery at the oat voltage. The charger can be connected to the battery indenitely and

will provide the appropriate prole. A two-stage charger is recommended in most instances

since it is the most versatile and can be permanently connected to attenuate the characteristic

discharge of unused batteries. A load can be put on the battery or batteries without altering

its ability to keep the battery at optimal charge.

A three-stage charger is the fastest charger. It charges the battery at a constant current

until the battery voltage reaches a slightly elevated level. The battery is maintained at

this voltage while the charging current diminishes to a low value, and then the battery is

switched to the oat voltage where it can be maintained indenitely. However, the charger

cannot differentiate between a current going to a load on the battery, or being absorbed by

the battery, so it can overcharge a battery supplying current to a load. A two-stage charger

is preferred for “loaded” batteries and a three-stage for idle or unloaded batteries during

recharging.

All of Analytic Systems’ chargers include adjustable output voltage for charging standard or

deep cycle lead-acid, VLRA or gel type batteries.

2 or 3 Stage Charging

100%

75%

50%

25%

Bulk

(Constant Current)

Float

(Constant Volts)

Time

Two Stage Charge

Volts

Amps

100%

75%

50%

25%

Bulk

(Constant Current)

Absorption

(Constant Volts)

Float

(Constant Volts)

Time

Three Stage Charge

Volts

Amps

BATTERY TEMPERATURE SENSOR

The battery temperature sensor can be connected to the charger to allow temperature

compensation of the battery charging voltage (1 is supplied with the unit).

The charger will work without the battery temperature sensor.

Troubleshooting

This unit provides LED indicators and a buzzer to help diagnose any problems. The unit

should sound the buzzer to alert you prior to shutting itself down. You should immediately

check the indicators to determine the cause of the shutdown.

CHARGING Indicates that the battery charger is charging the batteries:

If the LED is not on, the batteries may be fully charged and the

charger is supplying a oat voltage to the batteries to keep them

fully charged.

LOW OUTPUT Indicates that the output voltage is below normal because:

The current demanded by the devices connected to the unit

exceeds the maximum output current rating, causing the output

voltage to drop to maintain the current at the maximum level,

The input voltage is not high enough for unit to operate,

LOW INPUT Indicates that the input voltage is below normal because:

The input voltage is not in the correct range for proper operation of

the unit.

OVERTEMP Indicates that the Battery Charger is running too hot because:

Too much power is being drawn, turn off or unplug some devices.

The Battery Charger is located in a poorly ventilated area.

If the load exceeds the continuous rating for too long a period, the

temperature sensor inside the unit will turn off the outputs. After

the unit cools sufciently, it will automatically come back on. If this

happens frequently, remount the unit for increased airow so it

cools better.

If the load exceeds the continuous rating for too long a period, the temperature sensor inside

the unit will turn off the outputs. After the unit cools sufciently, it will automatically come

back on. If this happens frequently, remount the unit for increased airow so it cools better.

Page intentionally left blank

Inhaltsverzeichnis

Andere Analytic Systems Akkuladegerät Handbücher

Analytic Systems

Analytic Systems IBC320 Bedienungsanleitung

Analytic Systems

Analytic Systems BCD1000 Series Bedienungsanleitung

Analytic Systems

Analytic Systems BCD605 Bedienungsanleitung

Analytic Systems

Analytic Systems BCD315-12-24 Bedienungsanleitung

Analytic Systems

Analytic Systems BCD305 Series Bedienungsanleitung

Analytic Systems

Analytic Systems BCA1505MS Series Bedienungsanleitung

Analytic Systems

Analytic Systems BCD180 Series Bedienungsanleitung

Analytic Systems

Analytic Systems BCA610 Series Bedienungsanleitung

Analytic Systems

Analytic Systems BCA1505 SERIES Bedienungsanleitung

Analytic Systems

Analytic Systems BCD305 Series Bedienungsanleitung

Analytic Systems

Analytic Systems BCA1050 Bedienungsanleitung

Analytic Systems

Analytic Systems BCA1505U-24DW Bedienungsanleitung

Analytic Systems

Analytic Systems IBC320 Bedienungsanleitung

Analytic Systems

Analytic Systems BCA610V Series Bedienungsanleitung

Analytic Systems

Analytic Systems 99381 Bedienungsanleitung

Analytic Systems

Analytic Systems BCD310 Series Bedienungsanleitung

Analytic Systems

Analytic Systems BCD1015 SERIES Bedienungsanleitung

Analytic Systems

Analytic Systems BCD615-48-48 Bedienungsanleitung

Analytic Systems

Analytic Systems BCA1550MW Bedienungsanleitung

Analytic Systems

Analytic Systems BCD600-32-12 Bedienungsanleitung

Analytic Systems

Analytic Systems BCA1000R Bedienungsanleitung

Analytic Systems

Analytic Systems BCD615R Bedienungsanleitung

Analytic Systems

Analytic Systems BCA1000 Bedienungsanleitung

Analytic Systems

Analytic Systems BCD600 Series Bedienungsanleitung

Beliebte Akkuladegerät Handbücher anderer Marken

AA Portable Power Corp

AA Portable Power Corp Universal Smart Charger Bedienungsanleitung

Enelion

Enelion Vertica Bedienungsanleitung

RCA

RCA CHU6 Bedienungsanleitung

ANSMANN

ANSMANN ALCT 6/24-10 Bedienungsanleitung

Hitachi

Hitachi UC 18YRSL Fehlerbehebungshandbuch

Olympus

Olympus B-20 LPC Bedienungsanleitung

Exibel

Exibel ZH1708143 Bedienungsanleitung

Lenmar

Lenmar Mach 1 Bedienungsanleitung

CTEK

CTEK MXS 5.0 Bedienungsanleitung

ABB

ABB HT842379 Bedienungsanleitung

Nitecore

Nitecore Superb Charger SC4 Bedienungsanleitung

Renogy

Renogy RBC2125DS-21W Bedienungsanleitung

Braun

Braun BWC02M Bedienungsanleitung

CTEK

CTEK MXS 3.6 Bedienungsanleitung

Black & Decker

Black & Decker BDV090 Bedienungsanleitung

Trinity

Trinity DPD Bedienungsanleitung

Hulkman

Hulkman Sigma 1 Bedienungsanleitung

IKEA

IKEA koppla Bedienungsanleitung