ANTAIRA LNX-1802G Bedienungsanleitung

16-port 10/100TX + 2-Port 10/100/1000T

Mini-GBIC Combo

Industrial Ethernet Switch

User Manual

FCC Warning

This Equipment has been tested and found to comply with the limits for a

Class-A digital device, pursuant to Part 15 o f the F CC rules. These limits

are designed to provide reasonable protection against harmful interference

in a r esidential i nstallation. This equipment g enerates, uses, and c an

radiate radio frequency energy. It may cause harmful interference to radio

communications if the equipment i s not installed and used in a ccordance

with the instructions. However, there is no guarantee that interference will

not occur in a par ticular installation. If this equipment does cause harmful

interference t o r adio o r t elevision r eception, which c an be de termined b y

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a c ircuit different from that to

which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

CE Mark Warning

This is a Cla ss-A pr oduct. In a d omestic e nvironment this p roduct m ay

cause r adio i nterference i n w hich c ase t he user may b e r equired t o t ake

adequate measures.

Content

Introduction................................................................ 1

Features ................................................................... 1

Package Contents .................................................... 2

Hardware Description ............................................... 3

Physical Dimension .................................................. 3

Front Panel .............................................................. 3

Top View .................................................................. 4

LED Indicators ......................................................... 4

Ports ......................................................................... 6

Cabling ..................................................................... 8

Wiring the Power Inputs ......................................... 12

Wiring the Fault Alarm Contact .............................. 13

Mounting Installation .............................................. 14

DIN-Rail Mounting .................................................. 14

Wall Mount Plate Mounting .................................... 16

Hardware Installation .............................................. 17

Installation Steps .................................................... 17

Network Application................................................ 18

Troubles shooting ................................................... 19

Technical Specification........................................... 20

Introduction

The 16 10 /100TX + 2 1 0/100/1000T/Mini-GBIC Co mbo I ndustrial S witch is a cost-

effective s olution and meets the high r eliability r equirements demanded by i ndustrial

applications. Using fiber por t c an ex tend t he c onnection distance t hat i ncreases the

network elasticity and performance.

Features

System Interface/Performance

RJ-45 ports support Auto MDI/MDI-X Function

SFP (mini-GBIC) supports 100/1000 Dual Mode

Store-and-Forward Switching Architecture

Back-plane (Switching Fabric): 7.2Gbps

1Mbits Packet Buffer

8K MAC Address Table

Supports Wide Operating Temperature (-40oC ~ 75oC)

Case/Installation

IP-30 Protection

DIN-Rail and Wall Mount Design

Power Supply

Wide Range Redundant Power Design

Power Polarity Reverse Protect

Overload Current Protection

Provides EFT protection 3,000 VDC for power line

Supports 6,000 VDC Ethernet ESD protection

Package Contents

Please refer to the package content list below to verify them against the checklist.

16 10/100TX + 2 10/100/1000T/Mini-GBIC Combo Industrial Switch

Pluggable Terminal Block

User manual

2 wall mount plates with screws

One DIN-Rail (attached on the switch)

Compare the contents of the industrial switch with the standard checklist above. If any

item is damaged or missing, please contact the local dealer for service.

Hardware Description

In this paragraph, it will describe the Industrials witch’s hardware spec, port, cabling

information, and wiring installation.

Physical Dimension

16 10/100TX + 2 10/100/1000T/Mini-GBIC Combo Industrial Switch dimension (W x D x

H) is 72mm x 105mm x 152mm

Front Panel

The front panel of the 16 10/100TX + 2 10/100/1000T/Mini-GBIC C ombo I ndustrial

Switch is shown as below:

Front Panel of the industrial switch

Airflow around the switch must be

unrestricted. To prevent the switch from

overheating, there must be the following

minimum clearances:

•Top and bottom: 2.0 in. (50.8 mm)

•Sides: 2.0 in. (50.8 mm)

•Front: 2.0 in. (50.8 mm)

Warning!

Top View

The top panel of the 16 10/100TX + 2 10/100/1000T/Mini-GBIC Combo Industrial Switch

has one terminal block connector of two DC power inputs.

Top Panel of the industrial switch

LED Indicators

The diagnostic LEDs located on the front panel of the industrial switch provide real-time

information of system and optional status. The following table provides description of the

LED status and their meanings for the switch.

LED Status Meaning

PWR1

Green

Power 1 is active

Off

Power 1 is inactive

PWR2

Green

Power 2 is active

Off

Power 2 is inactive

Fault

Red

PWR1/PWR2 is inactive

Off

PWR1 & PWR2 are both active or no power

inputs

P1 ~ P16

Green

(Upper LED) Connected to network

Blinking

(Upper LED) Networking is active

Off

(Upper LED) Not connected to network

Yellow

(Lower LED) Ethernet port full duplex

Blinking

(Lower LED) Collision of packets occurs

Off

(Lower LED)

Ethernet port half duplex or not connected to

network

P17 ~ P18

(10/100/1000T)

Green

(Upper LED) Connected to network

Blinking

(Upper LED) Networking is active

Off

(Upper LED) Not connected to network

Green

(Lower LED) The port is operating at speed of 1000M

Off

(Lower LED)

The port is disconnected or operates at speed

of 10/100M

P17 ~ P18

Link/Active

(100/1000 SFP)

Green

SFP port is connected to network

Blinking

Networking is active

Off

Not connected to network

Ports

 RJ-45 ports

The UTP/STP ports will a uto-sense f or 10Base-T/100Base-TX connections (Fast

Ethernet) or 10Base-T, 100Base-TX, o r 10 00Base-T connections (Gigabit E thernet).

Auto M DI/MDIX m eans th at the sw itch can c onnect t o another switch or w orkstation

without changing straight through or crossover cabling. See the figures below for straight

through and crossover cable schematic.

 RJ-45 Pin Assignments

Pin Number

Assignment

Tx+

Tx-

Rx+

6 Rx-

Note

“+” and “-” signs represent the polarity of the wires that make up each wire

pair.

All ports on this industrial switch support automatic MDI/MDI-X operation, user can u se

straight-through cables (See figure below) for all network connections to PCs or servers,

or to other switches or hubs. In straight-through cable, pins 1, 2, 3, and 6, at one end of

the cable, are connected straight through to pins 1, 2, 3 and 6 at the other end of t he

cable. The table below shows the MDI and MDI-X port pin outs.

Pin MDI-X Signal Name MDI Signal Name

Receive Data plus (RD+)

Transmit Data plus (TD+)

Receive Data minus (RD-)

Transmit Data minus (TD-)

Transmit Data plus (TD+)

Receive Data plus (RD+)

Transmit Data minus (TD-)

Receive Data minus (RD-)

Straight Through Cable Schematic

Cross Over Cable Schematic

 2 Gigabit Copper/SFP (Mini-GBIC) combo port:

The I ndustrial s witch has t wo a uto-detected Giga po rt—UTP/STP/Fiber combo por ts.

The G igabit C opper (10/100/1000T) p orts s hould us e C ategory 5e or ab ove U TP/STP

cable f or the connection up t o 10 00Mbps. The S FP s lots s upporting dual m ode c an

switch t he c onnection s peed b etween 10 0 and 1 000Mbps. They are f or c onnecting t o

the net work segment with s ingle or m ulti-mode fiber. Y ou c an c hoose the appropriate

mini-GBIC module to plug into the slots. You can use proper multi-mode or single-mode

fiber according to the used SFP module. With fiber optic, it transmits speed up to 1000

Mbps and you can prevent noise interference from the system and transmission distance

up to 110 km, depending on the mini-GBIC module.

The small form-factor pluggable ( SFP) i s a compact optical transceiver used in optical

communications for both telecommunication and data communications applications.

Note

The SFP/Copper Combo module can’t both be used at the same time. The

SFP module has the higher priority than copper module; if you insert the

1000M SFP transceiver into the SFP module which is connected to the remote

device, the connection of the accompanying copper port will link down.

If you insert the 100M SFP transceiver into the SFP module even without a

fiber connection to the remote, the connection of the accompanying copper

port will link down immediately.

Inhaltsverzeichnis

Andere ANTAIRA Schalten Handbücher

ANTAIRA

ANTAIRA LMX-1600G Series Bedienungsanleitung

ANTAIRA

ANTAIRA LMX-0804G-SFP Series Bedienungsanleitung

ANTAIRA

ANTAIRA LNX-0601G-SFP Bedienungsanleitung

ANTAIRA

ANTAIRA LMP-0501-M-V2 Bedienungsanleitung

ANTAIRA

ANTAIRA LMP-1204G-SFP-bt Series Bedienungsanleitung

ANTAIRA

ANTAIRA LMP-0500 Series Bedienungsanleitung

ANTAIRA

ANTAIRA LNP-0800G-M12-67-24 Bedienungsanleitung

ANTAIRA

ANTAIRA LNP-0702G-SFP-24 Series Bedienungsanleitung

ANTAIRA

ANTAIRA LMP-1204G-SFP-bt-24 Series Bedienungsanleitung

ANTAIRA

ANTAIRA LMP-1202M-SFP-24 Bedienungsanleitung

ANTAIRA

ANTAIRA LNX-0702C-SFP Series Bedienungsanleitung

ANTAIRA

ANTAIRA LNX-800A-E Series Bedienungsanleitung

ANTAIRA

ANTAIRA LMP-0501-M-V2 Bedienungsanleitung

ANTAIRA

ANTAIRA LNP-2602G-SFP Series Bedienungsanleitung

ANTAIRA

ANTAIRA LMX-1204G-SFP-T-CC Bedienungsanleitung

ANTAIRA

ANTAIRA LNX-1600-E Series Bedienungsanleitung

ANTAIRA

ANTAIRA LNP-0602 Series Bedienungsanleitung

ANTAIRA

ANTAIRA LNX-1604G-SFP Series Bedienungsanleitung

ANTAIRA

ANTAIRA LNP-C501G-SFP-bt Series Bedienungsanleitung

ANTAIRA

ANTAIRA LMX-0601G-SFP-V2 Series Bedienungsanleitung

ANTAIRA

ANTAIRA LMP-1600G Series Bedienungsanleitung

ANTAIRA

ANTAIRA LNP-0800G-24 Series Bedienungsanleitung

ANTAIRA

ANTAIRA LNX-0500-M12-67 Series Bedienungsanleitung

ANTAIRA

ANTAIRA LNX-602N Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung