Antari HZ-100 Bedienungsanleitung

HZ-Series

HZ-100 / HZ-300 / HZ-400

Haze Machine User Manual

English Français Deutsch• • • 中文

Congratulations on the purchase of your new

ANTARI HAZE MACHINE

•Introduction

Thank you for choosing an Antari Haze Machine. You now own a rugged and powerful

state-of-the-art machine. Prior to use, we suggest that you carefully read all of the

instructions. By following the suggestions found in this user manual, you can look

forward to the best, virtuallyinvisible haze effect and reliable, satisfactory performance of

your Antari Hazer for years to come.

Please follow these operation and safety instructions to ensure a long and safe life for

your hazer.

•Danger of Electric Shock

․Keep this device dry; suitable for indoor/outdoor use.

․For all models, use grounded electrical outlet. Prior to use take care to determine

that the unit is installed at the rated voltage.

․HZ-300 is designed at a rated voltage of 100V - 120V / 50 Hz - 60 Hz.

․Always unplug your Antari Hazer before filling its tank.

․Turn off or unplug when not in use.

․This machine is not water-proof. If moisture, water, or hazer fluid gets inside the

housing, immediately unplug the unit and contact a service technician or your

ANTARI dealer before using it again.

․If power cable is damaged, please acquire specific power cable or accessories

replacements from manufacturer or authorized distributor.

•Danger of Burn

No user serviceable and modifying parts inside. Do not attempt to open the upper

housing cover and modify; otherwise may cause danger of burn.

․For adult useonly. Hazermust be installed out of the reach of children. Never leave

the unit running unattended.

․Position the haze machine in well-ventilated area. Please leave about 20cm spaces

surrounding the machine.

․Never aim the machine at open flames or close to flammable items.

․Never add flammable liquids of any kind (oil, gas, perfume) to the hazer liquid.

․Use only dealer recommended Antari high-quality hazer liquid (HZL). Please do not

use any other liquid which may cause erosion of inner parts.

․If your Antari Hazer fails to work properly, discontinue use immediately. Drain all

hazer liquid from the tank, pack the unit securely (preferably in the original packing

material), and return it to your ANTARI dealer for service.

․Please note before sending the machine for transporting purpose, make sure the

liquid inside the tank is fully emptied.

․Never drink hazer liquid. If it is ingested, call a doctor immediately. If hazer liquid

comes in contact with skin or eyes, rinse thoroughly with water.

Pay attention to all warning labels and instructions printed on the exterior of your Antari

Hazer

•Unpacking & Inspection

Open the shipping carton and verify that all equipment necessary to operate the system

has arrived intact. Before beginning initial setup of your ANTARI Hazer, make sure that

there is no evident damage caused by transportation. In the event that the unit’s housing

or cable is damaged, do not plug it in and do not attempt to use it until after contacting

your Antari dealer for assistance.

•Setup

1. Remove all packing materials from the shipping box. Check that all foam and plastic

padding is removed.

2. Place hazer on a flat surface and remove hazer liquid tank cap.

3. Your hazer may come with standard Timer remote HC-1 or Wireless HCR-1 remote

(except HZ-100, which will come separately). If you will be controlling your unit

remotely, firmly attach the remote control cable to the proper position.

•Operation

1. Place the unit on a flat surface. Plug power cord into a grounded electrical outlet.

2. Set the power switch to “ON” on the back of the machine. Make sure that the red

indicator light is on.

3. Remove the black liquid tank cap, pour hazer liquid into the liquid tank about 1/2 full,

be careful not to exceed the maximum fluid level. DO NOT OVERFILL. Use only

dealer-recommended high-quality hazer liquid . Any other types of fluid may cause

health hazard and damage the unit. Use of any other liquid may void warranty.

4. Connect the remote controller to the unit, press the red button ON/OFF to start up the

unit. (For further information on operating (including DMX) your Antari HZ-100, 300,

and 400 Hazer, see the section titled, ”Remote Control Operation”).

5. There’s an adjustable nozzle blade where you can adjust the angle of the haze output

by adjusting the thumb screws indicated below:

Antari HZ-100, HZ-300 and HZ-400 Haze machines produce safe, dry clean and virtually

invisible haze when used with HZL-1 Haze liquid with an extremely long hanging time.

For ideal results, haze when touch-up is needed.

•Caution

1. Always monitor and make sure that there is sufficient HZL liquid inside the tank during

operation.

2. Pour hazer liquid into the liquid tank about 1/2 full, be careful not to exceed the

maximum fluid level. DO NOT OVERFILL. The extra 1/2 tank space is reserved for

air-flow purpose. Overfilling will cause the unbalance in air pressure which will affect

the haze liquid to flow back to the compressor and may lead damage of the

compressor unit.

3. When the machine is operated for a longer period of time under open-air conditions,

falling dust/debris can enter the machine and may create residue inside the muffler of

the compressor. It will clog the filtration fibre on the muffler. Contact an authorized

Antari dealer to replace a new muffler only (please note that the old muffler is unable to

use repeatedly after washing or brushing). Long term use of the unit which has the

build-up residue on the muffler may cause an unsteady operation of the compressor. It

may even cause danger of burn under serious conditions.

4. If you have followed the above operation steps, and you still experience low output,

mechanical noise or no output at all, unplug the unit immediately from the mains.

Check the fluid level, the external fuse, the remote control connection, and the power

cable from the wall. If all of the above appears to be O.K., plug the unit in again. If the

hazer still does not function, discontinue operation or it may result in permanent

damage to the unit. Return the machine to your Antari dealer. Always drain tank

before mailing or transporting this unit.

•Remote Control Operation

HC-1:10 meter wired multi-function remote controller with ¼” stereo plug.

Red: CONTROL ON/OFF

Green: HAZE

Yellow: TIMER ON/OFF

DURATION and INTERVAL knobs

Connect the unit to the mains; set the power switch on the at rear of the machine to

on. Press the red button (CONTROL ON/OFF), the red indicator light will be on at

the same time. This haze machine is ready to operate.

Keep the green button (HAZE) pressed; the unit will produce continuous haze output.

Release the button to stop output. During this time, the red button (CONTROL

ON/OFF) is kept pressed while the red indicator light is still on.

Press the yellow button (TIMER ON/OFF) to activate the timer function for the knobs

DURATION and INTERVAL located on the top of the controller. Adjust the interval

between each haze emission (within the range from 10 to 200 seconds) by means of

the INTERVAL control knob. Adjust the duration of each haze emission (within the

range of 5 to 100 seconds) by means of the DURATION control knob.

HCR-1: Wireless remote controller with ¼” stereo plug for Antari Hazer models HZ-100 /

HZ-300 and HZ-400. Attach the receiver’s magnetic base to the hazer. Plug the

receiver’s cable into the hazer’s remote control input. Using the sending unit,

your Antari Hazer can be operated from a distance at least 50 meters when

under no obstruction. Start haze emission by pressing the small button on the

sending unit. Stop haze emission by pressing the large button. Multiple Antari

Hazers may be controlled using only one sending unit.

*The control of the master unit will override all other controllers when connecting the

haze machine via DMX*

•DMX Connector Pin Assignment

The machine (HZ-300 , HZ-400) provide 3 or 5 pin XLR connector for DMX connection.

Diagram below indicate pin assignment information

Function

Ground

Data-

Data+

•DMX Operation

The units HZ-300 and HZ-400 have on-board DMX control. These models use 1

channel to control volume output operation. Each channel has a value range of 0 to

255. The DMX channel is set on the rear panel of the HZ-300 and HZ-400 by setting

the dip switches to the desired channel.

If Channel A has a value from 0 to 5, the unit is OFF.

Between the values 6 to 255 the volume of fog output is regulated. With 6 being

the minimum volume of fog produced and 255 approaching the maximum. The

volume output rises as the DMX value is increased.

Note: The controls HC-1 and HCR-1 will be disabled when the hazer is in DMX mode.

•Hazer Liquid

Antari HZL-1 haze liquid was designed for the use with Antari hazers HZ-100, HZ-300,

and HZ-400. Antari HZL-1 is a non-toxic solution that produces a pure, translucent haze

with extremely long hang time and low moisture, perfect for HZ-100, HZ-300 and

HZ-400.

Important: Never mix oil-based and water-based hazer liquids. Before switching the

kind of hazer liquid in use, completely drain the hazer’s tank to avoid mixing.

•Technical Specifications

Model

HZ-100

HZ-300

HZ-400

Power supply:

115/230 V AC,

50/60 Hz~

115/230 V AC,

50/60 Hz~

115/230 V,

AC 50/60 Hz~

Power

consumption:

400 W

500 W

560 W

Output volume:

35 m³/min.

70 m³/min.

100 m³/min.

Tank capacity:

2.5 liters

Fluid

consumption:

25 Std./ liter

21 Std./ litre

16 Std./ liter

Weight:

12 kg

16 kg

19 kg

Dimensions

(LxWxH) mm:

485 x 250 x 235

500 x 300 x 232

500 x 320 x 250

Remote

included:

N/A

HC-1

Optional remote:

HC-1 / HCR-1

HCR-1

Save these instructions.

C08HZ4003

Andere Handbücher für HZ-100

Dieses Handbuch passt für folgende Modelle

Andere Antari Nebelmaschine Handbücher

Antari

Antari Fogger X-510II Bedienungsanleitung

Antari

Antari II Series Bedienungsanleitung

Antari

Antari WiFi-800 Bedienungsanleitung

Antari

Antari Onboard DMX Bedienungsanleitung

Antari

Antari M-7 RGBA Bedienungsanleitung

Antari

Antari MOBILE MB-55 Bedienungsanleitung

Antari

Antari DNG-250 Bedienungsanleitung

Antari

Antari Z-1500II Bedienungsanleitung

Antari

Antari CINEMA HAZE CH-1 Bedienungsanleitung

Antari

Antari S-120 Bedienungsanleitung

Antari

Antari Z-Stream Bedienungsanleitung

Antari

Antari Z-380 Bedienungsanleitung

Antari

Antari ICE-101 Bedienungsanleitung

Antari

Antari W-715 Bedienungsanleitung

Antari

Antari 20210616 Bedienungsanleitung

Antari

Antari FT-50 Bedienungsanleitung

Antari

Antari F-7X Bedienungsanleitung

Antari

Antari S-500 Bedienungsanleitung

Antari

Antari HZ-350 Bedienungsanleitung

Antari

Antari X-310PRO Bedienungsanleitung

Antari

Antari M-11 Bedienungsanleitung

Antari

Antari M-11 Bedienungsanleitung

Antari

Antari X FOGGER Bedienungsanleitung

Antari

Antari B-200 Bedienungsanleitung

Beliebte Nebelmaschine Handbücher anderer Marken

Boost

Boost BOOST-FOG400LED-BK Bedienungsanleitung

Home Accents Holiday

Home Accents Holiday FM1000-ASH Bedienungsanleitung

EuroLite

EuroLite ZEITGEIST FOG-1200 Bedienungsanleitung

Dyna-Fog

Dyna-Fog CYCLONE ULTRA 2734 Bedienungsanleitung

PROEL

PROEL DRAGO HEAVY PLFD150HY Bedienungsanleitung

Sparklyn

Sparklyn Y846 Bedienungsanleitung

Magicfx

Magicfx CO2 Gun Bedienungsanleitung

Ibiza

Ibiza LSM500LAS Bedienungsanleitung

Venue Lighting Effects

Venue Lighting Effects ULTRA MINI-FOGGER Bedienungsanleitung

High End

High End F-100 Bedienungsanleitung

Chauvet

Chauvet ARENA 2100 FLEX Bedienungsanleitung

Beamz

Beamz F1600 Bedienungsanleitung

Sagitter

Sagitter SG ARS900C Bedienungsanleitung

KISANKRAFT

KISANKRAFT KK-STF-480 Bedienungsanleitung

Orion

Orion OT-U250PP Leitfaden

Beamz

Beamz S2500 Bedienungsanleitung

American DJ

American DJ Dyno-Fog II Bedienungsanleitung

JB Systems

JB Systems FX 1700 Bedienungsanleitung