ANTENNAMAST AM2 Bedienungsanleitung
2
7
Manual Deployment
Quick Reference
43
3
c
a b c d
a
b c d ea
db
5
www.antennamast.com
1. Safe Installation
a. Level Site (maximum 5° slope)
b. Ensure adequate overhead and ground clearance
2. Set up the Tripod
a. Extend legs and tighten
b. Pull spring loaded pin
c. Open and level
d. Stake
3. Insert Top Tube
a. Tighten clamp
4. Install Accessories on Top Tube
a. Install payload accessories if required
b. Install payload(s)
c. Install guylines if required
5. Raise the Mast
a. Insert tube from bottom
b. Loosen clamp
c. Push tubes up
d. Tighten clamp
6. Install the Base Tube
a. Attach base plate to bottom of base tube
b. Attach to last mast tube
c. Loosen clamp and lower to ground
d. Tighten clamp
e. Stake base plate
7. Stake and Tighten Guy Lines
a. Clip carabineer to guy collar
b. Clip carabineer to stake
c. Stage and angle the guy stakes
d. Tigthen the guy lines
e. Lock the guy lines
Do not duplicate, alter, or copy without the written consent of e Will-Burt Company. © Copyright 2013 e Will-Burt Company
Version - TP-5001001-00 Date - 04/03/14 Remarks - Original Release
5
7
Lift Winch Deployment
43
6
ba c d e
b da
4
c e
Quick Reference
www.antennamast.com
Do not duplicate, alter, or copy without the written consent of e Will-Burt Company. © Copyright 2013 e Will-Burt Company
Version - TP-5001001-00 Date - 04/03/14 Remarks - Original Release
1. Safe Installation
a. Level Site (maximum 5° slope)
b. Ensure adequate overhead ground clearance
2. Set up the Tripod
a. Extend legs and tighten
b. Pull spring loaded pin
c. Open and level
d. Stake
3. Insert Top Tube
a. Tighten clamp
4. Install Accessories on Top Tube
a. Install payload accessories if required
b. Install payload(s)
c. Install guylines if required
5. Install Lift Winch
a. Install orange winch into tripod receiver and secure with orange hold down clamp
b. Crank winch counter-clockwise
c. Feed cable through orange base plate
d. Attach cable end to black key
e. Secure key to tripod leg braces
6. Raise the Mast
a. Place mast tube onto orange lift plate
b. Crank winch clockwise to raise tube until secured into tube in tripod
c. Loosen clamp
d. Raise tube until hand width remains
e. Tighten clamp
f. Repeat
7. Install Base Tube
a. Attach bottom of base tube to orange base plate
b. Raise and attach to last mast tube
c. Loosen clamp and lower to ground
d. Tighten clamp
e. Stake base plate
8. Stake and Tighten Guy Lines (Refer to the opposite side for guying instructions)
Inhaltsverzeichnis
Andere ANTENNAMAST Rack & Stand Handbücher
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
