Anthro 298 series Bedienungsanleitung

Anthro®File-Hanging 2 Drawer

Assembly Instructions

Enclosed Parts List

These Assembly Instructions are for the 298xx.

Before beginning assembly of your Anthro File-Hanging

2 Drawer, please take a moment to review the parts list below

to verify that your shipment is complete.

Review the assembly instructions of all Anthro products you

purchased and are planning to include in this installation prior

to beginning this assembly.

An electric drill and 1/8” drill bit are required for this assembly.

01– Housing Assembly .................... Qty. 1......................225-5481-xx

02– 6” Hanging Drawer Body .......... Qty. 1......................225-5474-xx

03– M4 x 8mm Phillips Screws ........Qty. 4...... 325-A129-18-01-00

04– Drawer Pull (DP 10B) ................ Qty. 2.......175-A138-10-01-03

Step 1

Pull the top drawer all the way out. Locate the drawer glides

on each side of the drawer body, and then locate the lever

inside each glide. Push the levers down to release the drawer

body from the housing and pull the drawer body away from the

housing.

Set aside the top drawer, then remove and set aside the lower

drawer.

TECHNOLOGY FURNITURE®

0104

Step 2 (requires a Philips Screw Driver)

Position the drawer pulls against the front of the drawers and

secure into place using the two Phillips screws.

05– 11” Hanging File Body............... Qty. 1 .....................225-5476-xx

06– 3/4” Wood Screws (2 extras) ......... Qty. 6......................325-5106-00

Drill Template (not shown)............ Qty.1 ..................... 300-5140-00

A 5/32” Anthro Hex Driver and Phillips Screwdriver (both not included)

will be required for this assembly.

Install the Drawer Pull using the

two Metric Screws.

Drawer Pull

Drawer Mounts

Levers

Drawer Glides

Drawers

Housing Assembly

M4 x 8MM Philips Screw

325-A129-18-01-00

Anthro® Corporation 10450 SW Manhasset Drive Tualatin, OR 97062

June 2014, Rev D anthro.com

SAVE THESE INSTRUCTIONS!

Step 3 (requires an electric drill and 1/8” drill bit)

Determine the location of your drawer unit on your

assembled workstation. Locate the Drill Template. Follow

its instructions to drill the holes for installing your drawer’s

housing assembly.

Once the holes have been drilled and the four wood screws

are partially installed, align the housing assembly with the

workstation so it opens to the front of the workstation and

the four keyholes on the assembly line up with the wood

screws. Slip the housing assembly over the wood screws

(Figure 1), then slide the housing to the back of the

workstation so the screws rest in the narrow end of the

keyholes on the housing (Figure 2). Tighten the wood screws

(Figure 3).

Install the remaining two wood screws into the center holes.

Step 4

Carefully, rotate your workstation so it’s right side up.

Reinstall the drawers to the housing assembly by aligning

the drawer glides (located on the drawers) with the drawer

mounts (located on the housing assembly). Then ﬁrmly push

the drawers all the way to the rear of your Cart.

Congratulations! Your drawer assembly is complete.

Items shown shaded are not included with this Accessory.

Figure 1

Insert Wood Screw

through Keyholes.

Figure 2

Push housing to the

back of the workstation

Figure 3

Fully tighten the

Wood Screws.

Keyholes

Firmly push the drawers towards the

rear of your cart.

Drawer

Glide

Center

Holes

Housing

Assembly

3/4” Wood Screw

325-5106-00

Questions? 1-800-325-3841

For warranty information, please visit:

http://www.anthro.com/support/warranty

Andere Anthro Inneneinrichtung Handbücher

Anthro

Anthro FAJ60zz/xx3 Series Bedienungsanleitung

Anthro

Anthro Elevate ELTA136 4 Series Bedienungsanleitung

Anthro

Anthro Elevate II Adjusta Bedienungsanleitung

Anthro

Anthro Space Pal Bedienungsanleitung

Anthro

Anthro FAJ30zz/xx3 Series Bedienungsanleitung

Anthro

Anthro Steve's Bench RTS90DGM Series Bedienungsanleitung

Anthro

Anthro AnthroCart Bedienungsanleitung

Anthro

Anthro fit 24 Bedienungsanleitung

Anthro

Anthro Zido ZHKzz Bedienungsanleitung

Anthro

Anthro Elevate II Bedienungsanleitung

Anthro

Anthro eNook II Bedienungsanleitung

Anthro

Anthro TAB16 Bedienungsanleitung

Anthro

Anthro GT12 Bedienungsanleitung

Anthro

Anthro Zido Cart Bedienungsanleitung

Anthro

Anthro Elevate Adjusta Series Bedienungsanleitung

Anthro

Anthro GT03 Series Bedienungsanleitung

Anthro

Anthro Steve's Station Standard Bedienungsanleitung

Anthro

Anthro Steve's Station Advanced Bedienungsanleitung

Anthro

Anthro Elevate Original Corner Bedienungsanleitung

Anthro

Anthro FCCzz/xx3 Series Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung