AOC LM-510 Bedienungsanleitung
Plug & Play Drivers for the AOC Spectrum Series Monitors are available
at AOC’s Web Site: www.AOCmonitor.com
LM-510
USER MANUAL
TABLE OF CONTENTS
FOR YOUR SAFETY -------------------------------------------------- 1
SAFETY PRECAUTIONS -------------------------------------- 2
SPECIAL NOTES ON LCD MONITORS ------------------- 3
BEFORE YOU OPERATE THE MONITOR --------------------- 3
FEATURES -------------------------------------------------------- 3
PACKING LIST --------------------------------------------------- 3
INSTALLATION INSTRUCTIONS --------------------------- 4
CONTROLS AND CONNECTORS -------------------------- 5
ADJUSTING THE VIEWING ANGLE ------------------------ 6
OPERATING INSTRUCTIONS ------------------------------------- 7
GENERAL INSTRUCTIONS ---------------------------------- 7
HOW TO ADJUST A SETTING ------------------------------- 9
ADJUSTING THE PICTURE -------------------------------- 9-10
HOW TO OPTIMIZE THE DOS-MODE----------------------- 10
PLUG AND PLAY -------------------------------------------------- 11
TECHNICAL SUPPORT(FAQ) ----------------------------------- 12-13
ERROR MESSAGE & POSSIBLE SOLUTION ----------- 14
HOW TO INSTALL INF & ICM FILE --------------------------- 15
APPENDIX ----------------------------------------------------------------- 16
SPECIFICATIONS --------------------------------------------- 16-17
FACTORY PRESET TIMING TABLE -------------------------- 18
CONNECTOR PIN ASSIGNMENT ----------------------------- 18
LIMITED THREE-YEAR WARRANTY --------------------------- 19-20
Thank you very much for choosing AOC LM-510 LCD Monitor.
We recommend that you take a few minutes to read carefully through this
manual before installing and switching on the monitor. Please keep this
manual in a safe place for your future reference.
1
Before operating the monitor please read this manual thoroughly. This
manual should be retained for future reference.
FCC Class B Radio Frequency Interference Statement
WARNING: (FOR FCC CERTIFIED MODELS)
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
NOTICE
1. The changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
2. Shielded interface cables and AC power cord, if any, must be used in
order to comply with the emission limits.
3. The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modification to this equipment. It is the
responsibilities of the user to correct such interference.
As an ENERGY STARPartner Envision Peripherals, Inc. has determined
that this product meets the ENERGY STARguidelines for energy efficiency.
WARNING:
To prevent fire or shock hazard, do not expose the monitor to rain or moisture.
Dangerously high voltages are present inside the monitor. Do not open the
cabinet. Refer servicing to qualified personnel only.
2
lDo not use the monitor near water, e.g. near a bathtub, washbowl, kitchen
sink, laundry tub, swimming pool or in a wet basement.
lDo not place the monitor on an unstable cart, stand, or table. If the
monitor falls, it can injure a person and cause serious damage to the
appliance. Use only a cart or stand recommended by the manufacturer or
sold with the monitor. If you mount the monitor on a wall or shelf, use a
mounting kit approved by the manufacturer and follow the kit instructions.
lSlots and openings in the back and bottom of the cabinet are provided for
ventilation. To ensure reliable operation of the monitor and to protect it
from overheating, be sure these openings are not blocked or covered. Do
not place the monitor on a bed, sofa, rug, or similar surface. Do not place
the monitor near or over a radiator or heat register. Do not place the
monitor in a bookcase or cabinet unless proper ventilation is provided.
lThe monitor should be operated only from the type of power source
indicated on the label. If you are not sure of the type of power supplied to
your home, consult your dealer or local power company.
lThe monitor is equipped with a three-pronged grounded plug, a plug with
a third (grounding) pin. This plug will fit only into a grounded power outlet
as a safety feature. If your outlet does not accommodate the three-wire
plug, have an electrician install the correct outlet, or use an adapter to
ground the appliance safely. Do not defeat the safety purpose of the
grounded plug.
lUnplug the unit during a lightning storm or when it will not be used for long
periods of time. This will protect the monitor from damage due to power
surges.
lDo not overload power strips and extension cords. Overloading can result
in fire or electric shock.
lNever push any object into the slot on the monitor cabinet. It could short
circuit parts causing a fire or electric shock. Never spill liquids on the
monitor.
lDo not attempt to service the monitor yourself; opening or removing
covers can expose you to dangerous voltages and other hazards. Please
refer all servicing to qualified service personnel.
lTo ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate configured receptacles marked
between 100 - 240V AC, Output 12Vdc Min. 3.5A.
lThe wall socket shall be installed near the equipment and shall be easily
accessible.
lFor use only with power adaptor manufacturer by :
Li Shin LSE9901B1250
Delta ADP-50XB, ADP-40TB
Linearity LAD6019AB4
Samsung 80AL15-7-SS(SA) (IBM)
PRECAUTIONS
3
The following symptoms are normal with LCD monitor and do not indicate a
problem.
NOTES
•Due to the nature of thefluorescent light, the screen may flicker during
initial use. Turn off the Power Switch and then turn it on again to make
sure the flicker disappears.
•You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
•The LCD screen has effective pixels of 99.99% or more. It may include
blemishes of 0.01% or less such as a missing pixel or a pixel lit all of the
time.
•Due to the nature of the LCD screen, an afterimage of the previous screen
may remain after switching the image, when the same image is displayed
for hours. In this case, the screen is recovered slowly by changing the
image or turning off the Power Switch for hours.
•The life of the fluorescent light used in the LCD monitor is approximately
10,000 hours. Contact your dealer or EPI service center for replacement
when the screen is dark, flickering or not lighting up. Never attempt to
replace it by yourself.
BEFORE YOU OPERATE THE MONITOR
FEATURES
•38.1cm(15”) TFT Color LCD Monitor
•Crisp, Clear Display for Windows
•Recommened Resolutions: 1024 X 768 @60Hz
•EPA ENERGY STAR®
•Ergonomic Design (MPRII Approved)
•Space Saving, Compact Case Design
The product package should include the following items:
1. LCD Monitor
2. Owner's Manual
3. Power Cord
4. External Adapter
5. Driver-Disk
FEATURES
CHECKING THE CONTENTS OF THE LM-510 PACKAGE
SPECIAL NOTES ON LCD MONITORS
4
INSTALLATION INSTRUCTIONS
SWIVEL BASE
Install Remove
Figure 1Installing and Removing the Swivel Base
POWERCORD
Power Source:
1. Make sure the power cord is the correct type that required in your area.
2. This LCD monitor has a universal power supply that allows operation in
either 100/120V AC or 220/240V AC voltage area (No user adjustment is
required.)
3. Connect the power cord into your LCD monitor’s power input socket, and
then plug the other end into a 3-pin AC power outlet. The power cord may
be connected to either a wall power outlet or the power outlet socket on
your PC, depending on the type of power cord supplied with your LCD
monitor.
NOTES
A certified power supply cord has to be used with this equipment. The
relevant national installation and/or equipment regulations shall be
considered. A certified power supply cord not lighter than ordinary polyvinyl
chloride flexible cord according to IEC 60227 (designation H05VV-F 3G
0.75mm
cord be of synthetic rubber according to IEC 60245 (designation H05RR-F 3G
0.75mm
INSTALLATION INSTRUCTIONS
5
VIDEO CABLE
Connecting the Video Cable: the LCD monitor comes with a built-in video
cable. Plug the signal cable′s 15-pin connector into the computer's video port
and tighten the two screws on the cable connector.
Connecting the Power Cord: Plug the power cord into the LCD monitor's AC
power socket. Then plug the power cord into a grounded AC outlet or UL-
approved power strip or the power output socket on your PC.
Caution: If the AC outlet is not grounded (with three holes), install the proper
grounding adapter (not supplied).
Figure 2 Connecting Cables
1. Signal Cable 3. AC Power Cord
2. DC-Jack Power Cable 4. External Adapter
CONTROLS AND CONNECTORS
6
INSTALLATION INSTRUCTIONS
•For optimal viewing it is recommended to look at the full face of the
monitor, then adjust the monitor’s angle to your own preference.
•Hold the stand so you do not topple the monitor when you change the
monitor’s angle.
•You are able to adjust the monitor’s angle from -5°to 25°.
Figure 3
NOTES
•Do not touch the LCD screen when you change the angle. It may cause
damage or break the LCD screen.
•Careful attention is required not to catch your fingers or hands when you
change the angle.
ADJUSTING THE VIEWING ANGLE
7
OPERATING INSTRUCTIONS
Press the power button to turn the monitor on or off. The other control knobs
are located at front panel of the monitor (See Figure 4). By changing these
settings, the picture can be adjusted to your personal preferences.
•The power cord should be connected.
•Connect the video cable from the monitor to the video card.
•Press the power button to turn on the monitor position. The power
indicator will light up.
Figure 4External Control Knob
EXTERNAL CONTROLS
1. Auto Config / Exit 2. / Brightness
3. / Contrast 4. MENU / ENTER
5. Power Button 6. LED
GENERAL INSTRUCTIONS
8
FRONT PANEL CONTROL
•Power:
Press this knob to switch ON/OFF of monitor’s power.
•MENU/Exit :
Active OSD menu or function adjust confirm or Exit OSD menu when in
Brightness/Contrast OSD status.
•Contrast / :
Adjust contrast or function adjust.
•Brightness / :
Adjust brightness or function adjust.
•Auto Config Key:
The Auto Adjust Key is used to automatically set the H POs, V Pos, Clock
and Focus.
•Power Indicator:
Green —Power On mode.
Orange —Off mode.
NOTES
•Do not install the monitor in a location near heat sources such as
radiators or air ducts, or in a place subject to direct sunlight, or excessive
dust or mechanical vibration or shock.
•Save the original shipping carton and packing materials, as they will come
in handy if you ever have to ship your monitor.
•For maximum protection, repackage your monitor as it was originally
packed at the factory.
•To keep the monitor looking new, periodically clean it with a soft cloth.
Stubborn stains may be removed with a cloth lightly dampened with a mild
detergent solution. Never use strong solvents such as thinner, benzene,
or abrasive cleaners, since these will damage the cabinet. As a safety
precaution, always unplug the monitor before cleaning it.
9
1. Press the MENU-Key to make the OSD window appear. See figure 5.
2. Press or to select the desired function. See figure 5.
3. Press the MENU-Key to select the function that you want to adjust.
4. Press or to change the settings of the current function.
5. When the OSD window is active, it shows the input signal timing. The "H"
stands for the horizontal frequency and "V" for the vertical frequency.
6. To exit and save, select the exit functions, or leave the monitor alone for
10 seconds. If you want to adjust any other function, repeat steps 2-4.
Figure 5The OSD Message
The description for function control LEDS
1. Contrast Adjust the picture contrast.
2. Brightness Adjust the picture brightness.
3. Focus Adjust picture Focus.
4. Clock Adjust picture Clock.
5. H- Position Adjust the horizontal position of the picture.
6. V- Position Adjust the vertical position of the picture.
7. Language Multi-Language selection
ADJUSTING THE PICTURE
HOW TO ADJUST A SETTING
Inhaltsverzeichnis
Andere AOC Monitor Handbücher
AOC
AOC 919Vwa Bedienungsanleitung
AOC
AOC LM565 Bedienungsanleitung
AOC
AOC 831S Bedienungsanleitung
AOC
AOC e2360Sd Bedienungsanleitung
AOC
AOC 1619Sw Bedienungsanleitung
AOC
AOC e2060Sda Bedienungsanleitung
AOC
AOC E2425SWD Bedienungsanleitung
AOC
AOC TS185LB Bedienungsanleitung
AOC
AOC I2769VM Bedienungsanleitung
AOC
AOC LE24A1330 Bedienungsanleitung
AOC
AOC e2440Va Bedienungsanleitung
AOC
AOC M2461FW Bedienungsanleitung
AOC
AOC AG273QCX Bedienungsanleitung
AOC
AOC E2357FH Bedienungsanleitung
AOC
AOC I2490PXQU Bedienungsanleitung
AOC
AOC AGON PRO AG276QZD Bedienungsanleitung
AOC
AOC LM760S Bedienungsanleitung
AOC
AOC G2460PG Bedienungsanleitung
AOC
AOC 2436Vw Bedienungsanleitung
AOC
AOC AGON AG273FXR Bedienungsanleitung
