AOpen AX45S-533 Datenblatt

Case Open Connecto

Thermal Sensor Connecto

CD-IN Connecto

WOL (Wake on LAN) Connecto

Front Audio Connecto

MODEM-CN Connecto

CNR Expansion Slot

IrDA Connecto

Front Panel Connecto

FDD Connecto

Supports 2nd USB Connecto

JP14 CMOS Clear Jumpe

2Mbit Programmable Flash ROM

Resettable Fuse

478-pin CPU socket (Willamette/

Northwood) with Voltage and Frequency

Auto-detection that supports Intel®

Pentium®4 1.4~2.4GHz+ CPU

AGP 4x Expansion Slot

32-bit PCI Expansion Slot x6

(PCI 6 supports slave mode PCI card only)

168-pin DIMMx3 supports PC100/133

SDRAM maximum up to 3 GB

SIS 645DX/961B Chipset

2200μF Low ESR Capacitors

ATX Power Connector

ATA/66/100/133 IDE Connector x2

4-pin 12V. ATX Power Connector

Dr. LED Connecto

(Upgrade Optional)

Realtek ALC201

Realtek RTL8100BL

(AX45S-533N only)

MIC-In

Line-In

Speaker Out

PS/2 Mouse

Connector SPP/EPP/ECP Parallel Port MIDI/Game Port

RJ45 10/100

LAN Jack

(AX45S-533N

only)

PS/2 Keyboard

Connector USB Port COM 1 Port COM 2 Port

Supports 3rd USB Connecto

FAN2 & FAN3 Connector

CPU FAN connector

WOM (Wake on Modem) Connecto

SPDIF Connecto

JP28 USB/Keyboard Wakeup Select Jumper

S/PDIF (Sony/Philips Digital Interface) is a newest audio transfer file format, which provides impressive

quality through optical fiber and allows you to enjoy digital audio instead of analog audio. Normally there

are two S/PDIF outputs as shown, one for RCA connector, the most common one used for consume

audio products, and the other for optical connector with better audio quality. Through a specific audio

cable, you can connect the S/PDIF connector to other end of the S/PDIF audio module, which bears

S/PDIF digital output. However, you must have a S/PDIF supported speaker with S/PDIF digital input to

connect to the S/PDIF digital output to make the most out of this function.

1. JP14 Clear CMOS

Everything you need to boot this

motherboard is included in this

Easy Installation Guide. For more

information, a complete Online

User's Manual can be found in the

Bonus Pack CD Disc. Thanks for

the help of saving our earth.

PART NO: 49.88I02.011 DOC. NO: AX45S533-EG-E0203A

You can clear CMOS to restore system default setting. To

clear the CMOS, follow the procedure below.

1. Turn off the system and unplug the AC power.

2. Remove ATX power cable from connector PWR2.

3. Locate JP14 and short pins 2-3 for a few seconds.

4. Return JP14 to its normal setting by shorting pin 1 & pin 2.

5. Connect ATX power cable back to connector PWR2.

Tip: When should I Clear CMOS?

1. Boot fail because of overclocking…

2. Forget password…

3. Troubleshooting…

This Motherboard x1

This Easy Installation Guide x1

80-wire IDE Cable x1

Floppy Disk Drive Cable x1

Registration Card x1

Bonus Pack CD x1

NORTON AntiVirus CD x1

Pin 1

Normal

(

default

)

Clear CMOS

2. S/PDIF (Sony/Philips Digital Interface) Connector

S/PDIF Connector

S/PDIF Module

(

tional

)

Audio

cable

Connecting to

RCA Cable

Connecting to

Optical Cable

+5VSB

S/PDIFOUT

GND

S/PDIFIN

1. Pull up the CPU socket lever and up to

90-degree angle.

2. Locate Pin 1 in the socket and look fo

a (golden) cut edge on the CPU uppe

interface. Match Pin 1 and cut edge.

Then insert the CPU into the socket.

3. Press down the CPU socket lever and

finish CPU installation.

Plug in the CPU fan cable to the 3-pin CPU FAN connector. If you have chassis fan, you

can also plug it on System FAN (FAN2) or AUX FAN (FAN3) connector.

CPU Ratio 8x, 9x, 10x… 21x, 22x, 23x, 24x

CPU FSB (By BIOS table) 100, 105, 108, 112 and 133MHz.

Northwood CPU CPU Core Frequency FSB Clock System Bus Ratio

Pentium 4 1.6G 1600MHz 100MHz 400MHz 16x

Pentium 4 1.6G 1600MHz 133MHz 533MHz 12x

Pentium 4 1.7G 1700MHz 133MHz 533MHz 13x

Pentium 4 1.8G 1800MHz 100MHz 400MHz 18x

Pentium 4 2.0G 2000MHz 100MHz 400MHz 20x

Pentium 4 2.2G 2200MHz 100MHz 400MHz 22x

Pentium 4 2.4G 2400MHz 100MHz 400MHz 24x

Pentium 4 2.4G 2400MHz 133MHz 533MHz 18x

Williamett CPU CPU Core Frequency FSB Clock System Bus Ratio

Pentium 4 1.5G 1500MHz 100MHz 400MHz 15x

Pentium 4 1.6G 1600MHz 100MHz 400MHz 16x

Pentium 4 1.7G 1700MHz 100MHz 400MHz 17x

Pentium 4 1.8G 1800MHz 100MHz 400MHz 18x

Pentium 4 1.9G 1900MHz 100MHz 400MHz 19x

Pentium 4 2.0G 2000MHz 100MHz 400MHz 20x

5. Setting CPU Voltage & Frequency

Setting CPU Core Voltage

This motherboard supports CPU VID function. The CPU core voltage will be automaticall

detected.

Setting CPU Frequency

This motherboard is CPU jumper-less design, you can set CPU frequency through the

BIOS setup, and no jumpers or switches are needed. The default setting is "table selec

mode". You can adjust the FSB from "CPU Host/SDRAM/PCI Clock" for overclocking.

BIOS Setup > Frequency / Voltage Control > CPU Speed Setup

3. Installing Processor

Note: If you do not match the CPU

socket Pin 1 and CPU cut edge well, it

may damage the CPU.

CPU socket lever

CPU Pin 1 and cut edge

Note: Some CPU fans do not have

sensor pin so they cannot support fan

monitoring.

CPU Fan Connector

Warning: SIS 645DX/961B Chipset

supports maximum 400MHz

(100/133MHz*4) system bus and

66MHz AGP clock; higher clock setting

may cause serious system damage

4. Installing CPU & System Fan

FAN3 Connector

This socket supports Micro-FC-PGA2 package CPU, which is the latest CPU package

developed by Intel. Other forms of CPU package are impossible to be fitted in.

FAN2 Connector

GND

+12V

SENSOR

Note: Since the latest processor,

Northwood, would detect the

clock ratio automatically, you

may not be able to adjust the

clock ratio in BIOS manuall

Secondary

Master (3rd)

Secondary

Slave (4th)

Primary

Slave (2nd) Primary

Master (1st)

8. Connecting IDE and Floppy Cables

9. Connecting Front Panel Cable

7. Connect IrDA Connector

The IrDA connector can be configured to support wireless infrared module, with this

module and application software such as Laplink or Windows 95 Direct Cable Connection,

the user can transfer files to or from laptops, notebooks, PDA devices and printers. This

connector supports HPSIR (115.2Kbps, 2 meters) and ASK-IR (56Kbps).

Install the infrared module onto the IrDA connector and enable the infrared function from

BIOS Setup, UART mode select, make sure to have the correct orientation when you plug

in the IrDA connector.

Connect 34-pin floppy cable and 40-pin, 80-wire IDE cable to floppy connector FDC and

IDE connector. Be careful of the pin1 orientation. Wrong orientation may cause system

damage.

Pin 1

ATA 33/66/100

IDE Connector

ttach the power LED, speaker, and reset switch connectors to

the corresponding pins. If you enable “Suspend Mode” item in

BIOS Setup, the ACPI & Power LED will keep flashing while the

system is in suspend mode.

Locate the power switch cable from your ATX housing. It is

2-pin female connector from the housing front panel. Plug this

connector to the soft-power switch connector marked SPWR.

Pin 1

FDD Connector

IDE 1 (Primary)

IDE 2 (Secondary)

6. Connecting ATX Power Connector

This motherboard comes with a 20-pin ATX power connector and an extra 4-pin connector

as shown below. Make sure you plug in the right direction. We strongly recommend you to

insert the 4-pin connector before connecting the 20-pin connector.

SPWR

GND

ACPI LED-

GND

ACPILED

GND

RESET

GND

+5V

IDE LED

+5V

GND

SPEAKER

Speaker

IDE LED

SPWR

CPI & PWR

LED

Reset

Pin 1

KEY

GND

IR_RX

+5V

IR_TX

IrDA Connector

Ground

12V

Ground

Pin1

COM

-5V

+5V

+12V

5VSB

PO-OK

COM

+5V

COM

PS-ON

COM

-12V

+3.3V

COM

+5V

COM

You can install LAN Driver under Windows95/98, Windows NT and Windows 2000 for

RealTek 8100BL PCI Fast Ethernet adapter by following steps.

Installing driver procedure on Microsoft Windows 95 :

-----------------------------------------------------

1. Select "Driver from disk provided by hardware manufacturer" when being asked which

driver you would like to install.

2. Specify the setup file pathname

[CD-ROM]:Driver\LAN\RTL8100\Windows\Win95\WIN95A(for Windows 95 and Win95A) o

[CD-ROM]:Driver\LAN\RTL8100\Windows\Win95 (for Windows 95 OSR2).

3. Follow the procedure and insert Windows 95 system disk to complete setup step.

4. Windows 95 will finish the other installation procedures automatically, and then restart you

system.

Installing driver for Win98/Win98 SE/Windows2000/Windows ME :

-------------------------------------------------------------------

1. Select "Driver from disk provided by hardware manufacturer" when being asked which

driver you would like to install.

2. Specify the setup file pathname

[CD-ROM]:Driver\LAN\RTL8100\Windows\WIN98 (for Windows 98/98 SE) or

[CD-ROM]:Driver\LAN\RTL8100\Windows\WIN2000 (for Windows 2000) or

[CD-ROM]:Driver\LAN\RTL8100\Windows\Windows ME (for Windows ME)

3. Follow the procedure and insert your system disk (Win98/Win98

SE/Windows2000/Windows ME) to complete setup step.

4. Win98/Win98 SE/Windows2000/Windows ME will finish the other installation procedures

automatically, and then restart your system.

10. Front Audio Connector

If the housing has been designed with an audio port on the front panel, you’ll be able to

connect onboard audio to front panel through this connector. By the way, please remove

5-6 and 9-10 jumper caps from the Front Audio Connector before connecting the cable.

Please do not remove these 5-6 and 9-10 yellow jumper caps if there’s no audio port on

the front panel.

Pin 1

12. Support Six USB Connectors

This motherboard provides six USB connectors to connect USB devices, such as mouse,

keyboard, modem, printer, etc. There are two connectors on the PC99 back panel. You

can use proper cable to connect other USB connectors to the back panel or front panel of

chassis.

13. Installing LAN Driver (AX45S-533N only)

11. 10/100 Mbps LAN onboard (AX45S-533N only)

Green/ACT

Orange/Speed

The South Bridge SIS961B includes a fast Ethernet controller on chip. On the strength of

Realtek 8100BL LAN controller on board, which is a highly-integrated Platform LAN

Connect device, it provides 10/100M bps Ethernet for office and home use, the Ethernet

RJ45 connector is located on top of USB connectors. The green LED indicates the link

mode, it lights when linking to network and blinking when transferring data. The orange

LED indicates the transfer mode, and it lights when data is transferring in 100Mbps mode.

To enable or disable this function, you may simply adjust it through BIOS.

KEY

GND

USB_ FP_P0+

USB_FP_P0-

USBPWR0

USB_FP_OC0

GND

USB_FP_P1+

USB_FP_P1-

USBPWR0

USB2 Connector

UD_FPOUT_L

UD_FPOUT_R

UD_MIC_BIAS

UD_MIC

AUD_RET_L

AUD_RET_

AUD_VCC

AUD_GND

fter you finish the setting of jumpers and connect correct cables. Power on

and enter the BIOS Setup, press <Del> during POST (Power On Self Test).

Choose "Load Setup Defaults" for recommended optimal performance.

14. Power-on and Load BIOS Setup

15. AOpen Bonus Pack CD 17. BIOS Upgrade

AOpen Easy Flash is more user-friendly than traditional flash method. The BIOS binary

file and flash routine are combined together and you simply run a single file to complete

the flash process.

1. Download new BIOS upgrade zipped file from AOpen's web site. For example,

AX45S533102.ZIP.

2. Run shareware PKUNZIP (http://www.pkware.com) which supports

miscellaneous operation systems to extract the binary BIOS file and the flash

utility. Or Winzip (http://www.winzip.com/) in Windows environment.

3. Save the unzipped file into a bootable floppy disk.

For example, AX45S533102.BIN & AX45S533102.EXE

4. Reboot the system to DOS mode without loading any memory handler (such as

EMM386) or device driver. It needs around 520K free memory space.

5. ExecuteA:> AX45S533102 and the program will do the rest of it.

DO NOT turn off the power during FLASH PROCESS until you are asked to!!

6. Reboot system and press <Del> to enter BIOS Setup, Choose "Load Setup

Defaults", then “Save & Exit Setup” and finish the BIOS upgrade.

Warning: The upgrade of new BIOS will permanently replace your original BIOS

content after flashing. The original BIOS setting and Win95/Win98 PnP information

will be refreshed and you probably need to re-configure your system.

16. Installing Onboard Sound Driver

You can use the autorun menu of Bonus CD disc. Choose the utility and driver and selec

model name.

Del

Warning: Please avoid of using "Load

Turbo Defaults", unless you are sure

our system components (CPU, DRAM,

HDD, etc.) are good enough for turbo

settin

This motherboard comes with a RealTek ALC201A AC97 CODEC, you can find the audio

driver from the Bonus Pack CD disc auto-run menu.

If you encounter any trouble to boot you system, follow the procedures

accordingly to resolve the problem.

Part Number and Serial Number

The Part Number and Serial number are printed on bar code label. You can find this

bar code label on the outside packing, on ISA/CPU slot or on component side of PCB.

For example:

Model name and BIOS version

AX45S-533 R1.02 Sep. 01. 2001AOpen Inc.

Award Plug and Play BIOS Extension v1.0A

Model name and BIOS version can be found on upper left corner of first boot screen

(POST screen). For example:

AX45S-533 is model name of motherboard; R1.02 is BIOS version

Make sure if the jumper settings for CPU and DRAMs are correct.

Clear CMOS.

Install the VGA card. Then connect your monitor and keyboard.

The problem was probably caused

by power supply or motherboard

failure. Please contact your reselle

or local distributor for repairing.

Perhaps your VGA card or monito

is defective.

Yes

It is very possible that your keyboard

is defective.

During system rebooting, press Del to enter BIOS Setup. Choose

“Load Setup Default".

The problem should be caused by the

IDE cables or HDD itself.

Re-install Windows 95, Windows 98 or Windows NT.

Yes

Turn off the power and unplug the AC power cable, then remove all

of the addon cards and cables, including VGA, IDE, FDD, COM1,

COM2 and Printer.

Turn on the power, and check if

the power supply and CPU fan

work properly.

Start

Check if there is display.

Press Ctrl, and Alt key at the

same time, hold them and then

press Del to see if the

stem reboots.

Turn off the system and

re-connect the IDE cable.

Check if the system can

reboot successfully.

End

P/N: 91.88110.201 is part number, S/N: 91949378KN73 is serial number.

Part No. Serial No.

Dear Customer,

Thanks for choosing AOpen products. To provide the best and fastest service to

our customer is our first priority. However, we receive numerous emails and

hone-calls worldwide everyday, it is very hard for us to serve everyone on time.

We recommend you follow the procedures below and seek help before contact

us. With your help, we can then continue to provide the best quality service to

more customers.

Thanks very much for your understanding!

Open Technical Supporting Team

Online Manual: Please check the manual carefully and make sure the

jumper settings and installation procedure are correct.

http://www.aopen.com/tech/download/manual/default.htm

Test Report: We recommend to choose board/card/device from the

compatibility test reports for assembling your PC.

http://www.aopen.com/tech/report/default.htm

FAQ: The latest FAQ (Frequently Asked Questions) may contain a

solution to your problem.

http://www.aopen.com/tech/faq/default.htm

Download Software: Check out this table to get the latest updated

BIOS/utility and drivers.

http://www.aopen.com/tech/download/default.htm

News Group: News posted by computer experts, you are welcome to join

any discussion and learning from it.

http://www.aopen.com/tech/newsgrp/default.htm

Contact Distributors/Resellers: We sell our products through resellers

and integrators. They should know your system configuration very well and

should be able to solve your problem efficiently and provide important

reference for you if next time you want to buy something else from them.

before contacting us. The part number, serial number and BIOS version

are also very helpful.

Pacific Rim

AOpen Inc.

Tel: 886-2-3789-5888

Fax: 886-2-3789-5899

America

AOpen America Inc.

Tel: 1-408-922-2100

Fax: 1-408-922-2935

Europe

AOpen Computer b.v.

Tel: 31-73-645-9516

Fax: 31-73-645-9604

Germany

AOpen Computer GmbH.

Tel: 49-2102-157700

Fax: 49-2102-157799

China

艾尔鹏国际上海(股)有限公司

Tel: 86-21-6225-8622

Fax: 86-21-6225-7926

Web Site: http://www.aopen.com

E-mail: Send us email by going through the contact form below.

English http://www.aopen.com/tech/contact/techusa.htm

Japanese http://www.aopen.co.jp/tech/contact/techjp.htm

Chinese http://www.aopen.com.tw/tech/contact/techtw.htm

German http://www.aopencom.de/tech/contact/techde.htm

French http:/france.aopen.com/tech/contact/techfr.htm

Simplified Chinese http://www.aopen.com.cn/tech/contact/techcn.htm

Japan

AOpen Japan Inc.

Tel: 81-048-290-1800

Fax: 81-048-290-1820

Andere Handbücher für AX45S-533

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere AOpen Hauptplatine Handbücher

AOpen

AOpen AX4PER-G Datenblatt

AOpen

AOpen MX4L Einrichtungshandbuch

AOpen

AOpen AX4SG WLAN Einrichtungshandbuch

AOpen

AOpen AK73 Series Einrichtungshandbuch

AOpen

AOpen AX4SPE Max II Einrichtungshandbuch

AOpen

AOpen DX34R-U Datenblatt

AOpen

AOpen AK79G MAX Datenblatt

AOpen

AOpen AX6B Plus Bedienungsanleitung

AOpen

AOpen AX63 Einrichtungshandbuch

AOpen

AOpen MX4BS Einrichtungshandbuch

AOpen

AOpen Fortress 9500 Bedienungsanleitung

AOpen

AOpen AK86-L Datenblatt

AOpen

AOpen AX63PRO Bedienungsanleitung

AOpen

AOpen AK73 Series Einrichtungshandbuch

AOpen

AOpen AX4T-533 Pro Einrichtungshandbuch

AOpen

AOpen MX4GV Einrichtungshandbuch

AOpen

AOpen MX3S Einrichtungshandbuch

AOpen

AOpen AX4BR-U Bedienungsanleitung

AOpen

AOpen AK77-400 Einrichtungshandbuch

AOpen

AOpen AX4C-G Datenblatt

AOpen

AOpen AX6BC Pro Gold Einrichtungshandbuch

AOpen

AOpen Fortress 7000 Bedienungsanleitung

AOpen

AOpen AK77 PLUS Bedienungsanleitung

AOpen

AOpen MK33M(A) Datenblatt

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung