APART CMSQ108 Bedienungsanleitung

MANUAL

CMSQ108

Please read this manual carefully before using the product. This will give you the

necessary product and installation instructions to assure a seamless installation and

non compromised overall sound quality.

Thanks for purchasing our APart CMSQ108 speaker. We have put great care and

effort in the design in order to bring you high quality sound. The CMSQ108 is an

elegant and very natural sounding in-wall/in-ceiling speaker. It easily outperforms

many standard cabinet speakers, both in sound quality and appearance.

CMSQ108 has a nominal impedance of 8Ω, allowing you to connect up to 2

speakers in parallel per 4Ω stable amplifier channel. Easy to integrate in high-end

audio chains, cinema surround systems or even high quality BGM systems, this

speaker offers a soundstage, unheard in this price range.

Introduction

• Keep this manual for future reference.

•When making the hole in your mounting panel to mount the APart CMSQ108

speaker, make sure there is sufficient clearance behind the panel (no

obstructions like A/C channels, power lines etc).

•Take care of your speaker wires, they should be free of damage. Damaged

speaker wires might result in poor sound quality and can damage amplifiers.

•Only use accessories specified by the manufacturer

•Make sure the mounting panel can support the speakers weight.

•Use sufficient amount of speakers to avoid death-spots.

•No mains power shall be connected to the loudspeakers, doing so will damage

the speaker.

•This apparatus should only be serviced by qualified personnel. If not warranty

Safety precaution

might be void.

•Use cable of the right gauge, certainly for long runs.

•Use cables with clear color indication and maintain polarity throughout the

whole system.

•Avoid loud feedback from microphones, this can damage your speaker.

•Please check the units condition after unpacking. If the outside of the carton

box has been damaged, inform your shipper immediately.

• Take notice that this speaker is meant for indoor use only!

Turn your living room walls into a wall of sound, at the highest possible hifi

standards, exactly there where you feel at home. CMSQ108 features a 5.5” bass-

mid speaker with a paper/Kevlar sandwich cone and a low loss rubber surround.

This guarantees highest possible definition and lowest sound coloration. High

frequencies are covered by a tiltable 1 inch silk dome tweeter, carefully matched

and tuned to deliver an amazing and detailed sound without the harshness usually

reproduced by cheap metal alloy domes.

Due to the narrow visible mounting flange and paintable detachable steel grilles,

the speakers can be integrated very discretely in even the most demanding

environments, in your living room, connected to your multiroom system, hifi or

cinema surround audio system… side by side to your flatscreen TV.

Mounting is easy and straightforward. The speaker clamps accept wall thickness

of 0 to 30 mm. By using our optional in-wall mounting cabinet, you can install the

speaker even in solid brick walls. Speaker cables are securely clamped in the gold

plated cable connectors, accepting thick speaker cables up to 6 mm².

The CMSQ speakers are not magnetically shielded, this is not necessary unless you

Features and benets

• Multi Room audio systems.

• Home Theatre systems.

• Lounges, Bars, Boutiques.

• Board rooms & Offices.

• Convention Centres, Hotels, sports facilities.

Recommended applications

Ideally, you should position the speakers on ear level or above, never below. When

the speakers are positioned far above the listening position (more than 60 cm),

pivot the tweeter and aim it towards the listening position.

Avoid the presence of wall corners, because these will augment reflections, causing

an unstable stereo image and boomy bass.

If possible, mount the speakers close to the sides of your flatscreen TV, about 1.5

meters or more apart from each other, depending on screen size and listening

distance. In general, the listening position and the left and right speaker should

form an equilateral triangle and the speaker should be positioned halfway the

screen or slightly higher.

Speaker positioning

install them close to a CRT screen. Flatscreens, the ideal partners for the CMSQ

speakers, are insensitive to magnetic fields. Instead we have invested in solid

gold plated speaker wire terminals, a carefully tuned crossover with high quality

components, solid steel speaker grille and of course top notch quality drivers. You

will hear the difference!

Recommended minimum installation volume is 4 liters. By using our optional in

wall speaker frame/cabinet, the optimum cabinet volume is guaranteed. There is

no upper volume limit. When the speaker is installed in a space with hard materials

such as bricks or concrete, additional cavity damping may be required. Suitable

materials are mineral insulation materials such as Rockwool or BAF (bonded

acetate fiber). Hard foam materials such as polystyrene and other polyfoams are

not suitable. Make sure that the used damping materials meet your local fire and

building requirements. Check that there are no obstacles such as electrical tubes,

wires or other pipes behind the speaker. Make sure the area behind the speaker is

free of small particles such as small stones. These particles can damage the vented

magnet system of the speaker. In cases of doubt, protect the rear of the speaker

with a small amount of BAF wadding.

To make grille removal easier, a special grille removal tool is supplied with the

speakers. Insert the tool in a corner of the grille and gently pull the grille out.

Repeat this step on all corners until the grille is entirely free. Do not attempt to pull

out the grille by pulling one side of the grille, this may cause damage to the grille

or the frame. Keep the tool at hand in case you need to remove the grille.

Be extra careful when positioning the tweeter: do not touch the tweeters membrane.

Keep the tilt angle within a range of 10 degrees from the neutral position.

Speaker mounting instructions

For hifi setups, mount the speakers between 1/2 and 2/3 of total wall height, for

walls up to 3 meters height, and stay at least 50 cm clear of adjacent walls. You

can also mount the speakers in a ceiling if necessary.

Note: when making the hole in your mounting panel, double check if there are no

cables or any other obstructions behind the mounting panel. Cutting the mounting

panel without this check might result in damaged infrastructure or power lines.

Using the cutout template

1. 2. 3.

5.4.

The CMS5BBI built-in box

Because we want to make the lives of installers easy APart offers a built-in box for

our square CMSQ108 speaker. The box is insulated to prevent resonance and is

custom-built. Once again, APart proves to be your one stop solution for all your

installed sound projects!

Use the correct polarity when daisy chaining speakers! When a mistake occurs

in your daisy chain, it can severely impact speaker performance as there will be

audio-cancellation.

The daisy chain options are endless and the setup will depend on the capabilities of

your amplifier. Make sure when daisy chaining speakers that the total impedance is

not lower than the lowest specified impedance of your amplifier. Not following this

rule might result in distorted sound and might even damage your amplifier.

Connecting the speaker

Series wiring speaker diagram: (+) (-)

Total resistance = R1 + R2 + R3 + R4 + ...

(+)

(-)

Total resistance =

Parallel wiring speaker diagram:

1/R1 + 1/R2 + 1/R3 + 1/R4 + ...

R1 = Resistance of speaker 1

R2 = Resistance of speaker 2

R3 = Resistance of speaker 3

R4 = Resistance of speaker 4

Speaker type in-wall/in-ceiling, square mounting

frame, two way hifi.

Recommended amplier power 15 to 120 watts per channel

Rated RMS power 50 W

Nominal impedance 8 Ohms

Frequency range 50* – 25000 Hz

Sensitivity 87 dB spl (2.83V/1m)

Dispersion at 1 kHz, 2 kHz, 4 kHz,

8 kHz

180, 170, 120, 80

Crossover frequency and slope 3000 Hz, 12 dB/oct

Bass-mid speaker 5.5” paper/Kevlar sandwich cone

Tweeter 1” soft dome, pivotable within approx

10 degrees in all directions

Chassis color White

Chassis type Plastic

Grille material Painted steel

Removable grille Yes

Fixing type dog-ears

IP classication 60

Dimensions outside H x W 167 x 167 mm

Mounting depth 73 mm

Total depth 80 mm

Cutout dimensions H x W 145 x 145 mm

Speaker weight 1360 g

Specications

Options: solid-wall mounting frame-cabinet/custom colour (CMS5BBI / PAINTCM)

* low frequency limit depends on room size, backspace volume, damping, proximity of

adjacent walls etc…

Polar diagram 1000 Hz Polar diagram 2000 Hz

Polar diagram 4000 Hz Polar diagram 8000 Hz

Polar diagrams

Inhaltsverzeichnis

Andere APART Sprecher Handbücher

APART

APART MASK12 Bedienungsanleitung

APART

APART VINCI 5 Bedienungsanleitung

APART

APART MASK4 Bedienungsanleitung

APART

APART SDQ5Pir Bedienungsanleitung

APART

APART OVO5P-W Bedienungsanleitung

APART

APART OVO8P Bedienungsanleitung

APART

APART OVO3T Bedienungsanleitung

APART

APART CMX20DT Bedienungsanleitung

APART

APART SDQ5P Bedienungsanleitung

APART

APART P60DT-BL Bedienungsanleitung

APART

APART CM6T Bedienungsanleitung

APART

APART MASK2 Bedienungsanleitung

APART

APART MASK12T Bedienungsanleitung

APART

APART MASK2 Bedienungsanleitung

APART

APART MASK series Bedienungsanleitung

APART

APART CM6TSMF Bedienungsanleitung

APART

APART CM1008D Bedienungsanleitung

APART

APART SDQ5Pir Bedienungsanleitung

APART

APART CM3T Bedienungsanleitung

APART

APART CM20DT Bedienungsanleitung

APART

APART MASK SERIES Bedienungsanleitung

APART

APART KUBO3T Bedienungsanleitung

APART

APART CM5EH Bedienungsanleitung

APART

APART CMSUB8 Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung