Apollo AIM-1SL Bedienungsanleitung

This manual contains confidential information and

may only be reproduced or distributed with the

written consent of Apollo Security Sales, Inc.

AIM-1SL & AIM-2SL

Hardware Manual

Revision Date: 19 OCT 2011

AIM-1SL & AIM-2SL Hardware Manual

by Apollo Security Inc.

mechanical, including photocopying, recording, taping, or information storage and retrieval systems - without the

written permission of Apollo Security, Inc.

While every precaution has been taken in the preparation of this document, Apollo Security assumes no responsibility

for errors or omissions, or for damages resulting from the use of information contained in this document or from the

use of programs and source code that may accompany it. In no event shall the publisher and the author be liable for

any loss of profit or any other commercial damage caused or alleged to have been caused directly or indirectly by this

document.

Advanced Electronic Controller For Apollo Access Control Systems

W A R N I N G

HIGH VOLTAGE, AC MAIN POWER SHOULD ONLY BE CONNECTED BY QUALIFIED,

LICENSED ELECTRICIANS. ALL APPLICABLE LAWS AND CODES MUST BE FOLLOWED. IF

THIS PRECAUTION IS NOT OBSERVED, PERSONAL INJURY OR DEATH COULD OCCUR

Power should not be applied to the system until after the installation has been completed. If this

precaution is not observed, personal injury or death could occur, and the equipment could be

damaged beyond repair.

-Verify that the external circuit breaker which supplies power to the device power supply is turned

off prior to installation.

-Verify that the output voltage of the power supply is within specifications prior to connection to the

device.

C A U T I O N

Several important procedures should be followed to prevent electro-static discharge (ESD) damage

to sensitive CMOS integrated circuits and modules.

-All transport of electronic components, including completed reader assemblies, should be in static

shield packaging and containers.

-Handle all ESD sensitive components at an approved static controlled work station. These work

stations consist of a desk mat, floor mat and a ESD wrist strap. Work stations are available from

various vendors including the 3M company.

FCC Compliance Statement

This device complies with Part 15 of FCC Rules. Operation is subject to the following two

conditions:

1.This device may not cause harmful interference, and

2.This device must accept any interference received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used

in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this device in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his/her own

expense. The user is advised that any equipment changes or modifications not expressly approved

by the party responsible for compliance would void the compliance to FCC regulations and

therefore, the user's authority to operate the equipment.

IMPORTANT INFORMATION

AIM-1SL & AIM-2SL Hardware ManualI

Table of Contents

Part I Introduction 2

...................................................................................................................................21Overview

...................................................................................................................................22 General Features

...................................................................................................................................33Modes Of Operation

Part II Hardware Layout 5

...................................................................................................................................61Terminal Connectors

...................................................................................................................................82DIP Switches

......................................................................................................................................................... 8DIP Switch Tables

......................................................................................................................................................... 9DIP Switch Function

...................................................................................................................................93Connectors

......................................................................................................................................................... 9Device Port Communication Driver Socket

......................................................................................................................................................... 9Additional Connectors

...................................................................................................................................94 LEDs

......................................................................................................................................................... 9Start Up Mode

......................................................................................................................................................... 10Normal Operation

...................................................................................................................................105Firmware

...................................................................................................................................106Memory Backup

...................................................................................................................................117 Additional Installation Information

......................................................................................................................................................... 11Mounting Holes

Part III System Wiring 13

...................................................................................................................................131Power

...................................................................................................................................132Grounding

......................................................................................................................................................... 13DC Ground

......................................................................................................................................................... 13RS-485 Signal Ground (SG)

......................................................................................................................................................... 14Safety (Earth) Ground

......................................................................................................................................................... 14Grounding System

......................................................................................................................................................... 14Grounding Potential Difference Checks Before Connecting

...................................................................................................................................143Communication Connection

...................................................................................................................................154RS-485 Communications Line

...................................................................................................................................175 Card Reader Wiring

...................................................................................................................................196Reader Input Wiring

......................................................................................................................................................... 19Input Supervision (Overview)

......................................................................................................................................................... 20Door Contact Input (Door Position Switch)

......................................................................................................................................................... 21Auxiliary Alarm Inputs

...................................................................................................................................217Output Relay Wiring

......................................................................................................................................................... 22Strike Wiring, General

......................................................................................................................................................... 22Strike Suppression Installation

......................................................................................................................................................... 23Strike Wiring, Internal Relay

IIContents

......................................................................................................................................................... 26ADA External High Security Relays

.................................................................................................................................................. 27Strike Wiring, External ADA-10/11, High Security Relay

.................................................................................................................................................. 28Additional Output Relay Wiring

.................................................................................................................................................. 28ADA DIP Switches/Jumpers

...................................................................................................................................308General Alarm Inputs

......................................................................................................................................................... 31Cabinet Tamper

Part IV Troubleshooting 33

...................................................................................................................................331Communications

...................................................................................................................................342Reader / Keypad

...................................................................................................................................343Input Zones

...................................................................................................................................344 Output relays

Part V Specifications 36

Part VI Supplemental Figures 38

Part VII Table of Figures 45

Part VIII Revision History 47

Index 48

Part

Introduction

2Introduction

1Introduction

An access control system provides a means to replace traditional key and lock systems, which are easy to

defeat because of the ease of copying of keys and use by unauthorized personnel. With electronic access

control, the exact areas a person is able to access as well as during what time is configurable through a

central control system. In addition to the power of greater control, a historical record is maintained which is

useful in the case of a system security breach or for other purposes including calculating work time and

facility use costing.

1.1 Overview

The AIM-1SL and AIM-2SL Downloadable Reader Interface modules provides complete connectivity for card

readers and for control of door strikes with additional alarm inputs. The AIM-1/2SL works in conjunction with

AAN and AAM series controllers to form a distributed processing network providing access control,

integrated alarm monitoring and remote device control and reaction. Typical use of the system is the control

of site access by control of door locking devices associated with card readers and PIN keypads and

maintaining logs of this access for later reporting. Many levels of further integration with building alarm and

monitoring systems, time and attendance systems, and video surveillance systems are also possible.

The AIM-1/2SL provides interface connections for a variety of card reader technologies, including proximity,

biometric, bar code, and infrared readers. Any card reader with standard Wiegand or mag stripe output can

be connected to the AIM-1/2SL.The AIM-1/2SL communicates with the AAN/AAM controller to process card

reads and alarm input activation. A downloadable card database of up to 20,000 cardholders and storage of

up to 7000 events allows the AIM-1/2SL to work independently after initial programming.

The AIM-1SL supports two readers that control the single onboard door strike relay. A successful access

grant on either reader will open the strike relay--this is known as 'Paired Mode'. Exit push button, door

contact and two auxiliary inputs are provided.

The AIM-2SL supports two readers that can be configured to control the two onboard relays in either paired

mode (using both readers to control a single strike relay) or in unpaired mode (where each reader will control

a separate strike relay). Exit push buttons, door contacts are available for two doors. When operating in

paired mode, the unused door inputs are available for auxiliary use.

See the Modes of Operation topic for more information on paired and unpaired mode.

1.2 General Features

·Supports 2 readers, keypads or reader/keypad combinations for 1 or 2 (AIM-2SL only) door control

·Full Stand Alone Operation with Local database of 20,000 cards or 7,000 events

·Multiple Card Formats

·Up to 8 Facility Codes

·2Relay Outputs

·Control of up to 4 ADA-10/11 High Security Relay Output Modules

·RS-485 or RS-232

·Field-Replaceable plug-in communication drivers

·Flash Memory for easy firmware upgrades

·Real Time Clock

·Surface-mount manufacturing technology

3AIM-1SL & AIM-2SL Hardware Manual

1.3 Modes Of Operation

CONFIGURATION / INITIAL MODE

To establish operating configuration, the AIM-1/2SL interface requires connection to an AAN or AAM

controller which is programmed via a software database interface program. Configuration options including

cardholders are stored in a central database and then transmitted via a proprietary encrypted protocol to the

AAN/AAM controller. Once programmed, the AAN/AAM controller will communicate to the AIM-1/2SL

interface to upload configuration the following configuration information:

·Card Reader Data Output Format: Wiegand or Mag Stripe

·Strike Time—The time duration that the strike relay will be energized for in the case of an access grant

·Held Open Time—After an access grant and a subsequent opening of the door contact, the time in which

the door contact must be closed before an alarm state is reported

·Initial Reader Mode—The access mode in which the reader will function upon powering up or when

communication has been interrupted with the AAN/AMM controller. The following modes are supported:

oCard Only—An access request is made by presenting a card to the reader. The data is verified against

the AIM-1/2SL database to ensure that the card has a valid Facility Code and Card Number.

oCard or PIN—Access requests are made either by presenting a card or by keying in a PIN (Personal

Identification Number) on a keypad. A card entry is process as in Card Only access mode.

oCard & PIN—A card must be read to start the access request. If the card is valid, the user is prompted

to enter the corresponding PIN. The request is granted only if the card and PIN match.

oLocked—No access granted. Reader ignores all cards and PIN entries.

oUnlocked—Door strike is continuously energized and the door contact input is not monitored. Access is

not controlled.

oFacility Code—The entire card contents are read by the AIM-1/2SL, but only the Facility Code is

checked, and if it matches a Facility Code downloaded from the AAN/AAM controller, access is granted.

PAIRED / UNPAIRED MODE (1 or 2 Door Control)

The AIM-1SL always works in paired mode. A successful card read on either reader will energize the single

onboard strike relay.

The AIM-2SL can be configured via software to operate in either paired or unpaired reader mode. In the first

case (the default mode), both readers of the AIM-2SL will control one door strike relay. In this case, the

second onboard relay serves as a local alarm relay and auxiliary inputs will be available. If unpaired reader

mode is selected, each reader will control a separate strike relay, thus two doors can be controlled. The

inputs that are auxiliary in paired mode are used for exit push button and door contact for the second reader

in this mode.

Part

Hardware Layout

5AIM-1SL & AIM-2SL Hardware Manual

2 Hardware Layout

Figure 2.1 AIM-1/2SL Diagram. Terminal connectors, DIP switch, output relays, device port driver

connection, and other component locations are shown.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Apollo Steuerungssystem Handbücher

Apollo

Apollo mart Color Pro Bedienungsanleitung

Beliebte Steuerungssystem Handbücher anderer Marken

Pentair Pool Products

Pentair Pool Products Compool Bedienungsanleitung

ComfortNET

ComfortNET CTK04 Bedienungsanleitung

Fireye

Fireye InSight II 95DSS3 Bedienungsanleitung

CAME

CAME G3000 Bedienungsanleitung

Idemia

Idemia MorphoAccess VP MD Bedienungsanleitung

Axis

Axis P1445-LE-3 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN TNC 150 B Bedienungsanleitung

CNC-Step

CNC-Step High-Z T-Series Bedienungsanleitung

Doosan

Doosan DVF Series Bedienungsanleitung

Honeywell

Honeywell KAP 140 Bedienungsanleitung

Honeywell

Honeywell vk41 series Bedienungsanleitung

AirBench

AirBench FPW Installationsanleitung

Cypress

Cypress HHR-3160 Bedienungsanleitung

CAME

CAME GLT40AOS Bedienungsanleitung

Zonex

Zonex GEN II -VVT Benutzerhandbuch

Altronics

Altronics K 9650 Bedienungsanleitung

micro-trak

micro-trak RoadMaster Bedienungsanleitung

micro-trak

micro-trak Calc-An-Acre II Bedienungsanleitung