Aprilaire 8570 Einrichtungshandbuch

Premium Programmable Thermostat

Safety & Installation

Instructions

Model 8570

READ AND SAVE THESE INSTRUCTIONS

TABLE OF CONTENTS

PAGE

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

WIRE REQUIREMENTS. . . . . . . . . . . . . . . . . . . . . . . . . 2

1. SELECT A MOUNTING LOCATION. . . . . . . . . . . 3

2. OPEN THE THERMOSTAT . . . . . . . . . . . . . . . . . . 4

3. MOUNT THE THERMOSTAT BASE

TO THE WALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

4. SET THE CONFIGURATION DIP SWITCHES

ON THE THERMOSTAT CIRCUIT BOARD . . . . . 6

PAGE

5. WIRE THE THERMOSTAT TO THE

HVAC EQUIPMENT . . . . . . . . . . . . . . . . . . . . . . . . 8

Diagram 1 – Single-Stage Furnace and AC . . . . . . 9

Diagram 2 – Two-Stage Furnace and AC . . . . . . . 10

Diagram 3 – Two-Stage Roof Top Unit . . . . . . . . 11

Diagram 4 – Boiler with AC . . . . . . . . . . . . . . . . . 12

Diagram 5 – Radiant Floor 1st Stage Heat

with Furnace 2nd Stage Heat and AC . . . . . . . . . 13

Diagram 6 – Single-Stage Heat Pump . . . . . . . . . 14

Diagram 7 – Two-Stage Heat Pump . . . . . . . . . . . 15

6. OPTIONAL – INSTALL AN OUTDOOR

TEMPERATURE SENSOR . . . . . . . . . . . . . . . . . . 16

PAGE

7. OPTIONAL – INSTALL AN AUTOMATIC

HUMIDIFIER CONTROL (AHC) . . . . . . . . . . . . . 19

8. OPTIONAL – INSTALL AN INDOOR

TEMPERATURE SENSOR . . . . . . . . . . . . . . . . . . 21

9. THERMOSTAT STARTUP . . . . . . . . . . . . . . . . . . 23

Verify Outdoor Temperature Sensor . . . . . . . . . . . 24

Check Fan Operation . . . . . . . . . . . . . . . . . . . . . . . 24

Verify AHC Connection . . . . . . . . . . . . . . . . . . . . . 24

Check Heating Operation . . . . . . . . . . . . . . . . . . . 26

Check Cooling Operation . . . . . . . . . . . . . . . . . . . 28

Check Emergency Heat Operation

(Heat Pumps Only) . . . . . . . . . . . . . . . . . . . . . . . . 29

PAGE

10. CUSTOMIZE THE

APPLICATION SETTINGS . . . . . . . . . . . . . . . . 30

Differential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Progressive Recovery . . . . . . . . . . . . . . . . . . . . . 31

Balance Points (Heat Pumps Only) . . . . . . . . . . . 32

Input Dealer Contact Information . . . . . . . . . . . . 33

Blower Extension for Humidity Control . . . . . . . 34

Monitors – Air Filter, Service Humidifier,

UV Lamp, Service HVAC . . . . . . . . . . . . . . . . . . . 35

WARNING

1. 120 Volts may cause serious injury from electrical shock. Disconnect electrical power to the HVAC equipment before

starting installation. This thermostat is not a 120-volt (line voltage) device.

2. Improper installation may cause serious injury from electrical shock. This product must be installed by a qualified

heating and air conditioning contractor in accordance with NEC Standards and applicable local and state codes.

3. Mercury is toxic and may be hazardous to health. Any replaced thermostats containing mercury must be disposed of

properly. Contact local authorities for disposal information.

Read this Installation Manual before beginning installation of the Aprilaire®8570 Thermostat. For questions call

Research Products Corporation at (800) 334-6011.

SAFETY INSTRUCTIONS

- 1 -

MODEL 8570 SPECIFICATIONS

Electrical

Thermostat Voltage: 24-volts ± 20% AC or DC

Total Load Current: 2A

Single Output Load Current: 1A

Solid State Output Residual Current: Less than 5 mA

Voltage Drop at Solid State Outputs: Less than 1-volt

Thermal

Operating Range: 32°F – 99°F (0 C – 37 C)

Display Accuracy: ±1°F between 60°F and 80°F, ±2°F outside this range

Control Accuracy: ±1°F

Control Range Heat: 40°F – 88°F (4 C – 30 C)

Control Range Cool: 42°F – 90°F (6 C – 32 C)

Heat/Cool Deadband: 2°F or C

1st Stage Differential: Adjustable 1°F – 3°F (1°F default)

2nd Stage Differential: Adjustable 1°F – 3°F (1°F default)

Temperature Offset: Adjustable 1°F – 4°F

- 2 -

Figure 1 and the table show the number of wires that must be available at the thermostat in stand-alone thermostat systems (i.e. not as

part of an Aprilaire®Model 6504 Intelligent Zone System). Figure 1 shows optional connections to both an outdoor temperature sensor and

an Aprilaire®Automatic Humidifier Control (AHC), but only one or the other can be used. All wire is standard 18-24 gauge thermostat cable.

When this thermostat is connected to a Model 6504 as

shown in Figure 2, only one four-wire cable need be run

from the thermostat to the Model 6504. Use standard

18-24 gauge thermostat cable.

OPTIONAL –

AUTOMATIC

HUMIDIFIER

CONTROL

(AHC)

HVAC

EQUIPMENT

MODEL 8570

THERMOSTAT

SEE

TABLE

2-WIRES

OPTIONAL –

OUTDOOR

TEMPERATURE

SENSOR

OPTIONAL –

INDOOR

TEMPERATURE

SENSOR

MODEL 8570

THERMOSTAT MODEL 65044-WIRES

Application # Wires Diagram (Page)

Single-Stage Furnace/AC 5 1 (9)

Two-Stage Furnace/AC 7 2 (10)

Two-Stage Roof Top Unit 7 3 (11)

Boiler w/AC (2-transformer) 6 4 (12)

Radiant 1st Stage Heat, 6 5 (13)

Furnace 2nd Stage and AC

Single-Stage Heat Pump 6 6 (14)

Two-Stage Heat Pump 8 7 (15)

WIRE REQUIREMENTS

Figure 1 – Thermostat Wire

Figure 2 – Model 6504 Wire

- 3 -

(1) SELECT A MOUNTING LOCATION

If installing the thermostat alone…

• Mount on an interior wall, in a frequently occupied space.

• Keep the thermostat 18" from an outside wall.

• Mount the thermostat approximately 5 feet above the floor.

Height requirements are different for compliance with the

Americans with Disabilities Act (ADA) – 48" maximum height

for forward reach and 54" maximum height for side reach.

• Thermostat can be mounted to a vertical junction box (j-box).

• DO NOT mount the thermostat:

– behind doors, in corners or other dead air spaces.

– in direct sunlight or near lamps, appliances or other

sources of heat.

– on an outside wall or wall exposed to an unconditioned

space (i.e. garage).

– in the flow path of a supply register, in stairways or near

outside doors.

– on a wall where concealed pipes or ductwork could

influence the sensor.

– near sources of electrical interference such as arcing

switch contacts.

If installing an indoor temperature sensor…

• Mount the thermostat where it can be readily accessed.

Note that the backlighting illuminates whenever a button

is pressed.

• Thermostat can be mounted on a vertical junction box (j-box).

• DO NOT mount the thermostat where the operating range

temperatures will be exceeded (i.e. attic or unventilated

equipment room).

• Mount the sensor in the same location as if installing a

thermostat alone.

(2) OPEN THE THERMOSTAT

Use your hands to pull the thermostat face off of the base. Separate one side at a time. There are latches on

either side of the thermostat.

If needed, the thermostat can be pried from the base by inserting a flat-head screwdriver (see Figure 3).

- 4 -

CAUTION

Loss of internal programs

may result from static

discharge to thermostat

circuit board. Avoid

touching the circuit board

and touch a grounded

metal object before

handling the thermostat.

INSERT SCREWDRIVER INTO 1 OF

4 SLOTS (2 ARE ON THE TOPSIDE,

2 ARE ON THE BOTTOM SIDE)

USE THE SCREWDRIVER TO SEPARATE THE

HOUSINGS. REPEAT ON THE REMAINING 3 SLOTS.

NOTE: THE HOUSINGS WILL NOT COMPLETELY

SEPARATE. PULL THE HOUSINGS APART WITH

YOUR HANDS TO COMPLETELY SEPARATE.

Figure 3

- 5 -

(3) MOUNT THE THERMOSTAT BASE TO THE WALL

1. Place the wire opening in the base over the wire entry

hole in the wall. Level the base (for appearance only)

and mark the screw locations. See Figure 4.

2. Use the supplied screws and wall anchors to mount

the thermostat to the wall. It is recommended that wall

anchors be used for installation to drywall/sheet rock.

• Drill a 3/16" hole for wall anchors.

• Drill a 3/32" starter hole for screws only.

3. For junction box mounting, screws are field supplied.

The thermostat can be installed on a vertical j-box.

4. Seal the wire entry hole(s) with caulk, drywall putty

or insulation to prevent drafts from inside the wall

cavity from affecting thermostat performance.

CIR

GND

IDS

ODT

I+

CAUTION

Minimize wire entry hole size and seal the hole – drafts from inside the wall could affect temperature readings.

Figure 4

- 6 -

(4) SET THE CONFIGURATION DIP SWITCHES ON THE THERMOSTAT CIRCUIT BOARD

H/C

GAS

MULTI

6504

ELEC

AHC

SINGLE

Figure 5

There are four dip switches

located on the back of the

thermostat (on the circuit

board) that must be set to

properly configure the

thermostat for operation

with the equipment it is to

control. Figure 5 shows

the default position for the

four switches.

Andere Handbücher für 8570

Inhaltsverzeichnis

Andere Aprilaire Thermostat Handbücher

Aprilaire

Aprilaire 8870 Bedienungsanleitung

Aprilaire

Aprilaire 8870 Bedienungsanleitung

Aprilaire

Aprilaire 8810 Bedienungsanleitung

Aprilaire

Aprilaire 8570 Bedienungsanleitung

Aprilaire

Aprilaire 8910W Bedienungsanleitung

Aprilaire

Aprilaire 8620 Einrichtungshandbuch

Aprilaire

Aprilaire 8555 Bedienungsanleitung

Aprilaire

Aprilaire 8556 Bedienungsanleitung

Aprilaire

Aprilaire 8810M Einrichtungshandbuch

Aprilaire

Aprilaire 8620 Bedienungsanleitung

Aprilaire

Aprilaire 8334 Bedienungsanleitung

Aprilaire

Aprilaire 8263 Bedienungsanleitung

Aprilaire

Aprilaire 8910W Einrichtungshandbuch

Aprilaire

Aprilaire S86N MU Bedienungsanleitung

Aprilaire

Aprilaire 8463 Bedienungsanleitung

Aprilaire

Aprilaire 8346 Bedienungsanleitung

Aprilaire

Aprilaire 8531 Bedienungsanleitung

Aprilaire

Aprilaire S86W MUPR Einrichtungshandbuch

Aprilaire

Aprilaire 8556 Bedienungsanleitung

Aprilaire

Aprilaire 8555 Bedienungsanleitung

Aprilaire

Aprilaire 8353 Bedienungsanleitung

Aprilaire

Aprilaire 8920W Einrichtungshandbuch

Aprilaire

Aprilaire 8800 Bedienungs- und Wartungshandbuch

Aprilaire

Aprilaire 8476 Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung