APsystems QS1-EU Bedienungsanleitung

2018/06/06 Rev1.1 Quick Installation Guide

QS1-EU Microinverter Quick Installation Guide

The sketch of QS1 support system.

All the PV modules are placed into two lines. Then put a QS1 in the middle of the two lines and make

sure it is easy to connect with four PV modules which are next to it, as well all the cables.

Step 1. Verify the grid voltage to match with microinverter rating

Step 2. The AC bus distribution

a. The AC bus is arranged at the proper position of the microinverter.

b. One end of the AC bus access junction box into power grid.

c. Wire the conductors of the AC bus: L - BROWN; N - BLUE.

NOTE: Wiring colour code can be different according local regulation, check all the wires of the

installation before connecting to the AC bus to be sure they match.Wrong cabling can damage

irreparably the microinverters, such an issue is not covered by the warranty.

Step 3. Attach the APsystems Microinverters to the racking

NOTE: Do not place the microinverters (including DC and AC connectors) where exposed to the

sun, rain or snow, even gap between modules. Allow a minimum of 3/4’’(1.5cm.) between the roof

and the bottom of the microinverter to allow proper air flow.The racking of install microinverter

must be reliably grounding.

d. Mark the location of the microinverter on the rack, with respect to the PV module

junction box or any other obstructions.

e. Mount one microinverter at each of these locations using hardware recommended

by your module racking vendor.when install microinverter, grounding washer

Must be facing the racking.

Step 4. Ground the system.

Step 5. Connect the APsystems Microinverter to AC bus cable

Push the microinverter AC connector to the trunk cable connector. Listen for the "Click".

Please scan the QR code to get

mobile app and more support

to help the installation.

Click

Power grid

Best Practice: Use the Bus

Cable Unlock Tool of AC

Bus to split the connectors.

grounding washer

2018/06/06 Rev1.1 Quick Installation Guide

NOTE: AC connector interface as follows.

Step 6. Install a Bus Cable End Cap at the end of AC bus cable.

a. Strip cable jacket. c. Insert the wires into the cable clamps.

b. Insert the cable end into the seal. d. Rotate the nut with 3.3N·m until the

latching mechanism meets the base.

Step 7. Place the PV modules and connect each QS1 to the PV modules

Step 8. Complete the APsystems installation map

a. Each APsystems Microinverter has removable serial number labels.

b. Peel labels off, affix one to the respective location on the APsystems installation map,and fill

in 1,2 in the label below,according to the layout on the roof..

c. The other one serial number label, posted on the solar module frame is easy to view the

position.

d. After the completion of installation drawings sent to APsystems website.

www.APsystems.com.

NOTE: Sequence of steps 1~8 can change for convenience of installation.

NOTE: Using APsystems' mobile app ArrayApp can make the installation and registration much

more simple.

Step 9. Start the operation

1. Turn on the AC circuit breaker on each microinverter AC branch circuit.

2. Turn on the main utility-grid AC circuit breaker. Your system will start producing.

power after a two-minute waiting time.

Product information is subject to change without notice.(Please download manuals at www.APsystems.com).

Nut

Seal

Body

NOTE: Cover any unused connectors with Bus

Cable Y-CONN Cap to protect the connectors.

NOTE: If the DC connector is not connected with the PV module,you

need to remove the dust cap,and cover the protection cap.

Inhaltsverzeichnis

Andere APsystems Wechselrichter Handbücher

APsystems

APsystems YC500i Series Bedienungsanleitung

APsystems

APsystems QT2D Bedienungsanleitung

APsystems

APsystems YC500A Bedienungsanleitung

APsystems

APsystems YC600 Bedienungsanleitung

APsystems

APsystems QS1-LK Bedienungsanleitung

APsystems

APsystems YC1000-3-ZA Bedienungsanleitung

APsystems

APsystems YC500 Leitfaden

APsystems

APsystems QT2 Bedienungsanleitung

APsystems

APsystems QT2 Bedienungsanleitung

APsystems

APsystems YC1000-3-NA Bedienungsanleitung

APsystems

APsystems EZ1 Series Bedienungsanleitung

APsystems

APsystems YC600 Bedienungsanleitung

APsystems

APsystems DS3 Series Bedienungsanleitung

APsystems

APsystems YC1000-3-220 Bedienungsanleitung

APsystems

APsystems YC1000-3-208 Bedienungsanleitung

APsystems

APsystems DS3D Bedienungsanleitung

APsystems

APsystems YC500I-LK Bedienungsanleitung

APsystems

APsystems QS1A Bedienungsanleitung

APsystems

APsystems YC600 Bedienungsanleitung

APsystems

APsystems YC600B Bedienungsanleitung

APsystems

APsystems YC1000-3 3-Phase Bedienungsanleitung

APsystems

APsystems QT2 Bedienungsanleitung

APsystems

APsystems DS3D-AU Bedienungsanleitung

APsystems

APsystems YC500I-ZA Bedienungsanleitung

Beliebte Wechselrichter Handbücher anderer Marken

Fourgroup

Fourgroup Easy Bedienungsanleitung

Velleman

Velleman PI300M Bedienungsanleitung

Sungrow

Sungrow SG350HX-US Bedienungsanleitung

WilTec

WilTec 61897 Bedienungsanleitung

SMA

SMA SUNNY BOY STORAGE 2.5 Bedienungsanleitung

Simplicity

Simplicity LANDLORD 316 Bedienungsanleitung

Santak

Santak SMAX 3000 Bedienungsanleitung

ATON

ATON RA.Store-3 Bedienungsanleitung

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Bedienungsanleitung

Tektronix

Tektronix CFG250 Bedienungsanleitung

Champion

Champion 200989 Bedienungsanleitung

Vanner

Vanner 20-500 Series Bedienungsanleitung

GE GEP Bedienungsanleitung

Astrel Group

Astrel Group Power Reducer Kurzanleitung

MULTIQUIP

MULTIQUIP GDP-5H Leitfaden

GoWISE

GoWISE PS1007 Bedienungsanleitung

Promate

Promate PM13500D ES Bedienungsanleitung

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Bedienungsanleitung