Aqualuma TRIM TAB LIGHT Bedienungsanleitung

*Please note red wire is positive and black is negative

Limited Warranty

(Please pass on to the vessel owner)

Aqualuma warrants all of its product range with a Three (3) year warranty to be free of defects in

workmanship and materials.

Aqualuma warranty will be deemed void if the product is improperly maintained or as a result

of misuse, neglect, improper installation or natural disasters such as ood, re, lightning or

unauthorized repairs or modications.

Aqualuma will replace at its option any product or part free of charge upon return of the defective

item and will pay for return freight within warranty period.

Aqualuma’s liability in all claims and events is limited to and shall not exceed the purchase price of

the Aqualuma product. No armation of fact or warranty expressed or implied other than that set

out in the warranty statement above is made or authorized by Aqualuma.

Aqualuma disclaims any liability claims that are due to misapplication, improper selection or

misuse. Any liability for consequential or accidental damages is expressly disclaimed.

AMG ( QLD) PTY. LTD.Trading as Aqualuma

Unit 4, 54 Siganto Drive

Helensvale

4212 Qld Australia

Email : [email protected]

Web: www.aqualuma.com

Fitting Instructions for

TRIM TAB LIGHT

Trim Tab Fitting Instructions

All Aqualuma lights have been tested before shipping.

It is recommended that you use a qualied boat builder to work out placement and tting

of your new underwater lights.

You will require the following to install your new Aqualuma lights: -

6 mm/1/4’drill, 5 or 6 cable/zip ties and a Fuse or Circuit Breaker

Step 1

With boat on hardstand or trailer work out where to t light unit to Trim tab or angle

bracket and mark hole centres as set out below.

Standard Trim Tab Light

Step 2

Drill the 2 holes required to mount the unit to theTrimTab or Bracket.

Step 3

Using the 2 nylock nuts and bolts supplied attach the unit to the TrimTab or Bracket and

tighten until just tight ( do not over tighten ) the nut and bolt need only to be tight

enough to stop the unit from moving on the mount.

Step 4

Mark out and drill a 6mm/1/4’hole well above the waterline for the wire and feed wire

through. Cable tie wire where needed then apply sealant around hole and clean.

Step 5

Connect the wires to a joiner box if using more than one light then run a positive and

negative feed from a fused switch to the joiner box.

Short Trim Tab Light

Andere Aqualuma Unterwasserbeleuchtung Handbücher

Aqualuma

Aqualuma GEN3 6 Series Bedienungsanleitung

Aqualuma

Aqualuma AQLBB*******-EU Series Bedienungsanleitung

Aqualuma

Aqualuma GEN2 3 Series Bedienungsanleitung

Aqualuma

Aqualuma Pathway Light Bedienungsanleitung

Aqualuma

Aqualuma GEN2 6 Series Bedienungsanleitung

Aqualuma

Aqualuma GEN3 3 Series Bedienungsanleitung

Beliebte Unterwasserbeleuchtung Handbücher anderer Marken

Keldan

Keldan VIDEO 18X 25000lm CRI82 Bedienungsanleitung

Oase

Oase ProfiLux Garden LED RGB Bedienungsanleitung

Oceanled

Oceanled DISCOVER D3 Bedienungsanleitung

NORBIT

NORBIT AQUA FCL600 Bedienungsanleitung

Keldan

Keldan VIDEO 8XR Ambient 18000lm Bedienungsanleitung

Ikelite

Ikelite PCm - LED Light Bedienungsanleitung

LIGMAN

LIGMAN NEMO 2 Bedienungsanleitung

Oase

Oase Lunaqua 2 Handbuch

Kripsol

Kripsol 061511213000 Bedienungsanleitung

Wibre

Wibre 4.0291 Bedienungsanleitung

Certikin

Certikin PU9CS Bedienungsanleitung

lumishore

lumishore SMX53-SUPRA Bedienungsanleitung

Pyle

Pyle PLEDFN8 Bedienungsanleitung

Filix

Filix Arpool XM Bedienungsanleitung

HEISSNER

HEISSNER U 130-T Bedienungsanleitung

emaux

emaux NP300 Series Bedienungsanleitung

Oceanled

Oceanled XD16 Bedienungsanleitung

Hella marine

Hella marine NaviLED Bedienungsanleitung