Arada Ecoburn Plus Medium Gas Bedienungsanleitung
PLEASE RETAIN THIS GUIDE FOR FUTURE REFERENCE
BK710 SPECIFIC Rev 02 ISSUE DATE : 28/11/2017
BS EN 613: 2001 + A1: 2003 +C1:2008
Ecoburn Plus Gas
Ecoburn Plus Medium
Gas
Arada Ecoburn Plus Gas Stove
Ecoburn Plus Gas
Page 2 BK 710 Specific
Congratulations on the purchase of your new Arada stove!
More than 30 years of experience has been put into the development of
your stove to ensure ultimate performance and years of trouble free use and
enjoyment. Every detail of your stove has been carefully designed and
engineered which is why we are so confident in the reliability of our products.
Your Arada stove is built to the highest standard of craftsmanship using the
best materials and the most modern equipment available. It is a highly efficient
and sophisticated piece of machinery and when properly installed and
operated it should provide a lifetime of heating satisfaction.
Should you have any questions about your stove which are not covered by this
manual, please contact the Arada retailer in your area, call our technical
support department on +44 (0)1297 632052 or visit our website
www.aradastoves.com which offers a wealth of information on how to care for,
and get the best from your stove.
Please ensure that you read these instructions in full and understand them
before operating your stove.
Arada has a policy of continuous product development and therefore we
reserve the right to amend specifications without prior notice. Due to printing
cycles, items or options may be described before they are generally available
or after they have ceased. Please check with your retailer or dealer if you are
unsure about any aspect of your stove, its installation or correct use.
Contents
Installation & Service
1 Appliance Information
1.1 Conditions Of Installation…………………………………....…..
1.2 Flue & Chimney Suitability……………………………….. …….
2 Installation
2.1 Hearth……………………………………………………………..
2.2 Siting ……………………………………………………………...
2.3 Flue Connection ………………………………………………….
2.4 Ventilation ………………………………………………………..
2.5 Gas Connection ………………………………………………….
2.6 Placement Of The Ceramic Logs……………………………….
2.7 Operating Instructions …………………………………………..
2.8 Spillage ……………………………………………………………
2.9 Customer Education …………………………………………….
3 Servicing Instructions
3.1 Replacement Parts……………………………………………….
User Instructions
4 Important Information
4.1 Important Information For Use Of Appliance………………….
4.2 Layout Of Ceramic Logs…………………………………………
4.3 Operating Control Locations…………………………………….
4.4 Battery Replacement…………………………………………….
4.5 Fire Control Valve—Red Indicator Meaning………………….
4.6 Using The Remote Display Handset…………………………..
4.7 Trouble Shooting / FAQ …………………………………………
4.8 Remote Display Handset Optional Features…………………..
5 Guarantee
5.1 Guarantee………………………………………………………...
5.2 Terms & Conditions………………………………………………
5.3 General…………………………………………………………….
5.4 Notes……………………………………………………………….
Ecoburn Plus Gas
BK 710 Specific Page 3
4
5
6
6
7
7
7
8-9
10-13
14
14
14
16
17-18
19
20
20
21-22
22
23-27
28
28-29
30
31
Installation & Service
SECTION 1 : APPLIANCE INFORMATION
BK 710 Specific Page 4
Ecoburn Plus Gas
Model ARADA ECOBURN PLUS
Gas type G20 (natural gas)
Supply pressure (measured at test elbow), mbar 20
Injector (x1) Stereomatic 500
Oxypilot type Erta PG-82 -10
Nominal Heat Input (Qn), kW (Gross)-Maximum Rate 6.2
Gas consumption at max rate (m3/h) 0.590
Minimum heat input Kw (Gross) 2.5
Gas consumption at minimum rate (m3/h) 0.238
Gas connection 8mm compression
Remote gas valve TESCO1 RF868-15
Countries of Destination GB and IE
Efficiency class 1
NOX 2
1.1 - Conditions Of Installation
Before installation, check that the local distribution conditions, nature of the gas and pressure, and adjustment
of the appliance compatible. It is the law that only a competent person installs all gas appliances i.e.: a gas
registered installer in accordance with the current edition of the gas safety (installation and use) regulations or
the rules in force, failure to do so could lead to prosecution.
The installer must be gas safe registered.
The installation must also be in accordance with all relevant parts of the local and national buildings regula-
tions where appropriate, the building regulations (Scotland consolidation) issued by the Scottish development
department, and all applicable requirements of the following standard codes of practice :
1. BS 5871 part 1
2. BS 6891 installation of gas pipework
3. BS 5440 parts 1 & 2 installation of flues and ventilation
4. BS 8303 installation of domestic heating appliances
5. IS 813 Domestic gas installation (Republic Of Ireland)
No purpose made additional ventilation is normally required for this appliance when in-
stalled in G.B. when installing in I.E. please consult document IS 813 domestic gas in-
stallation, which is issued by the national standards authority of Ireland, if installing in
Northern Ireland please consult local building regulations. In Scotland, please consult
the current edition of the building standards regulations, issued by the Scottish
executive. Any purpose made ventilation must be checked periodically to ensure that it
is free from obstruction.
PLEASE NOTE—The stove is a very heavy appliance and care must be used when lifting and moving, we
recommend 2 people lift following lifting guidelines. Preferably wear gloves when lifting.
BK 710 Specific Page 5
Ecoburn Plus Gas
1.2 - FLUE & CHIMNEY SUITABILITY
This appliance is designed for use with conventional brick built or lined chimneys, all flues must conform to the
following minimum dimensions :
Before commencing installation a flue or chimney should be inspected to ensure that all of the following
conditions are satisfied :
1. Check that the chimney / flue only serves one fireplace and is clear of any obstruction, any dampers or
register plates must be removed or securely locked in the open position.
2. Brick / stone built chimneys or any chimney or flue which has been used for an appliance burning fuel
other than gas must be thoroughly swept.
3. Any under floor air supply to the fireplace must be completely sealed off.
4. Ensure that the inside of the chimney / flue is in good condition along its length and check that there is
no leakage of the smoke through the structure of the chimney / flue during and after the smoke pellet
test.
5. Using a smoke pellet check there is an updraft in the chimney / flue and that the smoke can be see
coming from the terminal / pot outside.
There must be no leakage of smoke through the structure of the chimney during or after the smoke
pellet test and it is important to check the inside upstairs rooms adjacent to the chimney / flue.
Check the chimney pot / terminal and general condition or the brickwork and masonry. If the chimney /
flue is in poor condition or if there is no up-draught do not proceed with the installation, if there is a
history of down draught conditions with the chimney / flue, again do not proceed until the fault has been
fixed.
A tested and certificated flue terminal or cowl suitable for the relevant flue type should be considered.
6. A spillage test must always be carried out during commissioning of this appliance.
Minimum dimension of flues 125 mm Minimum effective height of all flue types 3 metres
ECOBURN PLUS GAS
Page 6 BK 710 Specific
WARNING
This stove is fitted with a spillage monitoring system consisting of a thermal switch, which shuts the appliance
off in the event of a blocked flue or inadequate flue pull occurring.
The system shall not be adjusted by the installer or shall not be put out of action.
When the spillage monitoring system is required to be replaced, only original manufacturers parts shall be
used.
If the stove switches off for no apparent reason, the appliance should not be used until expert advice is
obtained and the fault rectified.
All surfaces, except the control valve, are working surfaces and become very hot in use. They must not be
touched or any combustible materials put on them.
It is recommended that a fireguard complying to BS 8423 should be fitted for protection of young children or
elderly or infirm persons.
The door assembly has to be removed, to allow access to remove the glass frame assembly. Allow to
cool before removing this, as it will become very hot and is a working surface in use.
SECTION 2 : INSTALLATION
2.1 - HEARTH
The stove must be installed on a non-combustible hearth with the hearth material being at least 12mm thick,
the hearth must protrude at least 150mm (6”) in front of the stove and be of a size sufficient to accommodate
the stove.
2.2 - SITING
The stove must not be installed in a bathroom.
Clearance from non-combustible material in the fireplace opening must be at least to dimensions in the table
below :
NOTE : Fitting the stove any closer to the back may cause nuisance shutdown of the stove
as the airflow may be compromised and the thermal cut off will operate.
Position
Above
Back
Left
Right
Distance mm
100 mm
100 mm
100 mm
100 mm
300 mm
300 mm
300 mm
300 mm
Combustible MaterialNon Combustible Material
BK 710 Specific
2.3 - FLUE CONNECTION
The flue should be at least 3m high and at least 125mm diameter (5”) at no point should there be any
negative or horizontal gradients in the flue pipe.
It is recommended that a minimum height of 600mm from the stove before any significant change of
direction of the flue.
2.4 - VENTILATION
Ventilation should be in accordance with national regulations in the UK purpose provided ventilation is not
normally required BS5871 part 1 and in IE IS813 (IE Only).
2.5 - GAS CONNECTION
The gas connection can be made by removing the glass frame assembly; remove all the fixing screws a
keep safe for future use. Once the frame has been removed, the 4 no. fixings, holding the burner in place
can be removed and access to the gas inlet elbow can be gained. Once the connection has been made and
soundness verified the burner can be replaced ensuring correct position and the 4no. fixings replaced.
Page 7
ECOBURN PLUS GAS
BK 710 Specific Page 8
2.6 - PLACEMENT OF THE CERAMIC LOGS
The logs should be positioned as in the pictures below.
DO NOT CHANGE THE FUEL BED LAYOUT, THE TYPE OR NUMBER OF LOGS.
ECOBURN PLUS GAS
Step 1 Step 2
Step 3 Step 4
Step 5 Step 6
BK 710 Specific
ECOBURN PLUS GAS
Correct completed ceramic log layout
Page 9
Step 7 Step 8
Step 9 Step 10
Step 11
2.7 - OPERATING INSTRUCTIONS
Below the gas controls, which are situated at the bottom left hand side of the appliance (when viewed
looking at the appliance door).
Below the remote control handset.
Page 10 BK 710 Specific
ECOBURN PLUS GAS
Battery Compartment Cover
Increase FlamePower Button
Decrease Flame
Indicator Light Power Isolator Switch Battery Compartment Release Lever
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Arada Herd Handbücher
Arada
Arada FARRINGDON FAR 12 HEATSHIELD Series Bedienungsanleitung
Arada
Arada Stratford Bedienungsanleitung
Arada
Arada BK605 Bedienungsanleitung
Arada
Arada Villager Bedienungsanleitung
Arada
Arada BK545 Bedienungsanleitung
Arada
Arada Lagom Bedienungsanleitung
Arada
Arada Ecoburn S3 Montageanleitung
Arada
Arada Ecoboiler Bedienungsanleitung
Arada
Arada Aarrow Bedienungsanleitung
Arada
Arada I Series Bedienungsanleitung
Arada
Arada Aarrow DEFRA Bedienungsanleitung
Arada
Arada Stratford Bedienungsanleitung
Arada
Arada AX Bedienungsanleitung
Arada
Arada Aarrow Bedienungsanleitung
Arada
Arada Holborn Gas Bedienungsanleitung
Arada
Arada Villager Bedienungsanleitung
Arada
Arada Cassette Stove Bedienungsanleitung
Arada
Arada Stratford Ecoboiler Bedienungsanleitung
Arada
Arada Farringdon Catalyst Eco Bedienungsanleitung
Arada
Arada Puffin Bedienungsanleitung
