Arbor Technology Nova-AGS1 Bedienungsanleitung

Phone number: 01945 410950

support@arborgardensolutions.co.uk

http://www.arborgardensolutions.co.uk

Trading address: Unit 11, Cattle Dyke, Wisbech, England, PE1 34NR

Nova 3 Door MDF Cupboard 400mm Wide (Nova-AGS1)

Before you commence the assembly process, we recommend that you read these instructions

thoroughly beforehand to familiarise yourself with the assembly process and to also check that

you have the correct components. If for any reason you need assistance, you can find our

contact details on the top of page of these instructions.

We highly recommend that any assembly is carried out on a flat, level surface if possible

and that you use another person to assist you if necessary. Also, all parts have stickers

with part numbers attached and for your convenience all guide holes are pre-drilled.

Package contents

2x Side panels (Part nr: AGS1_1)

3x Partitions (Part nr: AGS1_2)

1x Base (Part nr: AGS1_3)

1x Back panel (Part nr: AGS1_4)

1x Top door (Part nr: AGS1_5a)

1x Middle door (Part nr: AGS1_5b)

1x Bottom door (Part nr: AGS1_5c)

3x Leg panel (Part nr: AGS_2)

Bundle with fixings

Tools required

Electric screwdriver

No.2 and No.3 Pozi bits

Phillips Screwdriver

Hammer

Phone number: 01945 410950

support@arborgardensolutions.co.uk

http://www.arborgardensolutions.co.uk

Trading address: Unit 11, Cattle Dyke, Wisbech, England, PE1 34NR

Step 1

Step 2

Lay the side panel (Part nr: AGS1_1) on a flat even

surface.

Take 6 hinge plates and prepare 4x16mm wood screws. Make

sure you are using pre-drilled guide holes.

Step 2.1

Step 3

Make sure that a small arrow on hinge plate facing

outwards.

Repeat steps 2 to 2.1 for the rest of hinge plates.

Phone number: 01945 410950

support@arborgardensolutions.co.uk

http://www.arborgardensolutions.co.uk

Trading address: Unit 11, Cattle Dyke, Wisbech, England, PE1 34NR

Step 4

Step 5

Take base panel (AGS1_3) and align with side panel

(AGS1_1) pre-drilled guide holes as shown in step 5.

Flip your side panel of the side together with your base

panel and secure with confirmat screws as shown in step

5.1

Step 5.1

Step 6

In this step you might require an assistant, to hold you a

side panel.

Now, take 3x partition panels (AGS1_2) and proceed to step

Phone number: 01945 410950

support@arborgardensolutions.co.uk

http://www.arborgardensolutions.co.uk

Trading address: Unit 11, Cattle Dyke, Wisbech, England, PE1 34NR

Step 7

Step 8

Align partition panels as shown in the picture and secure

via pre-drilled guide holes using confirmat screws.

Flip your side panel back to starting position and your

cabinet at this stage should look like this.

Step 9

Step 10

Take you second side panel (AGS1_1) and secure it via pre-

drilled guide holes with confirmat screws. Don’t forget to

secure base as well.

**IMPORTANT**

Now, flip your cabinet as shown in the picture. Make sure

that hinge plates are facing down.

**IMPORTANT**

Phone number: 01945 410950

support@arborgardensolutions.co.uk

http://www.arborgardensolutions.co.uk

Trading address: Unit 11, Cattle Dyke, Wisbech, England, PE1 34NR

Step 11

Step 12

Now take your back panel (AGS1_4) and place on top of

your cabinet back.

Secure back panel with provided nails using hammer. Make sure

that nails are spaced out approximately 30mm from each

corner.

Step 13

Step 14

At this stage, take 4 cabinet legs and secure them into

place as shown in the picture. These legs are adjustable

heigh 100mm to 130mm. You can adjust them at this stage

or later when you will position your cabinet into upright

position.

Position your cabinet into upright position (make sure you

have assistance) and at this stage your item should look like

this.

Phone number: 01945 410950

support@arborgardensolutions.co.uk

http://www.arborgardensolutions.co.uk

Trading address: Unit 11, Cattle Dyke, Wisbech, England, PE1 34NR

Step 15

Step 16

Now take your doors (AGS1_5a/AGS1_5b/AGS1_5c).

Place hinges into pre-drilled holes and secure with wood screws

4x16mm. Repeat this step for all three doors.

Step 17

Step 18

At this stage, take first door (AGS1_5a) and secure it into

position as shown in the picture. Than take second door

(AGS1_5b) and secure into position and lastly take

(AGS1_5c) door and secure it into position. **Important**

insert the front of the plate in to front arm of the hinge.

Now press back arm of the hinge until you hear the click.

Now, using pre-drilled guide holes secure cabinet handles.

Phone number: 01945 410950

support@arborgardensolutions.co.uk

http://www.arborgardensolutions.co.uk

Trading address: Unit 11, Cattle Dyke, Wisbech, England, PE1 34NR

Step 19

Step 20

At this stage your cabinet should look like this. However,

when you install the doors, they may be out of

alignment.

Start first by adjusting machine screw market as number one on

the arm of the hinge, this will adjust your door left-to-right or

horizontal position. If you need to adjust in and out position

simple adjust cam-screw marked as number two. To adjust up

and down or vertical position, simple release hinge plate.

Step 21

Step 22

Last step is to cover legs with a panel. Take leg panels

(AGS_2) and secure leg supports using pre-drilled guiles

and wood screws.

Take shorter and longer braces and align predrilled guide holes.

Phone number: 01945 410950

support@arborgardensolutions.co.uk

http://www.arborgardensolutions.co.uk

Trading address: Unit 11, Cattle Dyke, Wisbech, England, PE1 34NR

Step 23

Step 24

Secure both panels using confirmat screws. Repeat steps

for the other side.

Take your finished leg panel and clip it to the legs.

Phone number: 01945 410950

support@arborgardensolutions.co.uk

http://www.arborgardensolutions.co.uk

Trading address: Unit 11, Cattle Dyke, Wisbech, England, PE1 34NR

**IMPORTANT**

If you have more than one Nova product, we strongly advise to connect them together via

guide holes, which you can find in each side panel corner. Also, please note that cabinets

and wall cupboards need fixing to walls conventionally using wall plugs and screws

suitable for your wall material. Please employ a tradesman if in doubt.

Step 1

Step 1.1

To connect cabinet to other cabinet, use pre-drilled

guide holes as shown in the picture. This should be your

last step, when you decided about the layout of your

Nova Garage Cabinet Systems.

Your 3 door cabinet is now completed!

We hope that you found your product quick and easy to assemble but if you require further

assistance or have any questions you can contact us via details above.

Andere Arbor Technology Inneneinrichtung Handbücher

Arbor Technology

Arbor Technology Nova-AGS3 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung