Ardisam Earthquake E43 Bedienungsanleitung

•

Ardisam.corn

OME43

Rev. 3/28/07

Parts Online

Earthquake®

OPERATOR'S MANUAL &

PARTS EXPLOSIONS

E43 EARTH AUGER POWERHEAD

,7"

ARDISAM

Earthouake

ASSEMBLY INSTRUCTIONS AND PARTS EXPLOSIONS

E43 Model_

WARRANTY

Earthquake, a division of Ardisam Incorporated, offers a

one

year

limited warranty to be free from defects in materials and

workmanship for the service life of the product including the

engine, not to exceed twelve consecutive months from the

date of purchase. This warranty applies to the original owner

with a proof of purchase and is not transferable.This warranty

applies only to products which have not been subjected to

negligent use, misuse, alteration, accident or if repairs have

been made by anyone outside our factory. This warranty

supersedes all other warranties either expressed or implied

and all other obligations or liabilities on our part. Ardisam,

Inc., does not assume, and does not authorize any other

person to assume for us, any liability in connection with the

sale of our products. Warranty work must be sent directly to

Ardisam, Inc. or one of our authorized service centers and

performed by them. To obtain warranty service and replace-

ment instructions, contact our customer service department

at 800-345-6007 or by writing to: Ardisam, Inc., 1690 Elm

Street, Cumberland, WI 54829. All items must be shipped

prepaid. Ardisam, Inc. will at no charge, repair or replace,

at their discretion, any defective part which falls under the

conditions stated above. Ardisam retains the right to change

models, specifications and price without notice.

INTRODUCTION

THANK YOU ...

for purchasing an Earthquake® Powerhead from Ardisam, Inc. We

have worked to ensure that the earth auger meets high standards

for usability and durability. With proper care, your earth auger will

provide many years of service. Please take the time to read this

manual carefully to learn how to correctly operate and maintain

your earth auger. Congratulations on your investment in quality.

CONTENTS

Registration & Warranty



Safety



3-4

Operation



5-8

Maintenance & Storage



8-9

Service, Troubleshooting & Repair



10-11

Parts Explosions



12-15

REGISTRATION

Record your model number and serial number in the space provided

for easy reference. Fill out and mail the registration card located in

your parts packet. Warranty is valid only if your completed registration

card is received by Ardisam, Inc., at time of purchase.

Model Number



Serial Number



Date of Purchase



Place of Purchase



Page 2

800-3454007

Ardisam.com

IMPORTANT

INDICATES HELPFUL INFORMATION FOR PROP-

ER ASSEMBLY, OPERATION, OR MAINTENANCE

OF YOUR EQUIPMENT.

WARNING

CALIFORNIA PROPOSITION 65 WARNING

ENGINE EXHAUST FROM THIS PRODUCT CON-

TAINS CHEMICALS KNOWN TO THE STATE OF

CALIFORNIA TO CAUSE CANCER, BIRTH DE-

FECTS, OR OTHER REPRODUCTIVE HARM.

CAUTION

CAUTION INDICATES YOU CAN CAN BE HURT OR

YOUR EQUIPMENT DAMAGED IF THE SAFETY IN-

STRUCTIONS THAT FOLLOW THIS SIGNAL WORD

ARE NOT OBEYED.

Earths:mice'

ASSEMBLY INSTRUCTIONS AND PARTS EXPLOSIONS

E43 Model

SAFETY

OWNER'S RESPONSIBILITY

Accurate aasembly and safe and effective use of the auger is the

owner's responsibility.

Read and follow all safety instructions.

Carefully follow all assembly instructions.

Maintain the auger according to directions and schedule

included in this Earthquake operator's manual.

Ensure that anyone who uses the auger is familiar with all

controls and safety precautions.

SPECIAL MESSAGES

Your manual contains special messages to bring attention to poten-

tial safety concerns, machine damage as well as helpful operating

and servicing information. Please read all the information carefully

to avoid injury and machine damage.

NOTE: General information is given throughout the manu-

al that may help the operator in the operation or service of

the machine.

IMPORTANT SAFETY PRECAUTIONS

Please read this section carefully.

Operate the auger according

to the safety instructions and recommendations outlined here and

inserted throughout the text. Anyone who uses this auger must

read the instructions and be familiar with the controls.

This symbol points out important safety instructions

which if not followed could endanger your personal

safety. Read and follow all instructions in this manual

before attempting to operate this equipment.

Do not carry the auger powerhead between holes with the engine run-

ning.

The auger should not rotate when the engine is idling. If it does rotate

when engine is idling, contact Ardisam,Inc. for instructions.

Always keep hands, feet, hair and loose clothing away from any mov-

ing parts on engine and auger.

Do not allow children to operate this power auger. Do not allow adults

to operate the auger without proper instruction.

Do not operate any power equipment under the influence of alcohol or

drugs.

Keep all screws, nuts and bolts tight.



Engine should be turned off and cool, spark plug wire must be re-

moved from spark plug before any repairs are attempted.

Temperature of muffler and nearby areas may exceed 150g F (65

C).

Avoid these areas.

Never run engine indoors or in an enclosed area. Engine exhaust

contains carbon monoxide, an odorless and deadly gas.

It the earth auger will not turn in a hole, turn engine off and allow to

cool before attempting to remove it manually.

Use only original equipment parts from Ardisam

including all nuts and bolts.

800-345-6007

Page 3

Arclisam.corn

CAUTION

HOT GASES ARE A NORMAL BY-PRODUCT OF A

FUNCTIONING CATALYTIC CONVERTER. FOLLOW

ALL SAFETY INSTRUCTIONSTO PREVENT BURNS

AND FIRES.

Earthauake

ASSEMBLY INSTRUCTIONS AN

IPARTS EXPLOSIGNS

E43 Model

ENGINE SAFETY PRECAUTIONS

Warning Carbon Monoxide Poisoning

All engines contain carbon monoxide in their exhaust. Carbon

monoxide iaa deadly, colorless, tasteless, odorless gas Which

may be present

Men

if you do not smell or see any engine

exhaust. Levels of carbon monoxide, which can be deadly,

can be present for days in art enclosed area that has poor

ventilation. Any level of carbon monoxide, if inhaled, can cause

headaches, drowsiness, nausea, dizziness, confusion and.

eventually death. If you experience any of these symptoms,

seekiresh air and medical attention immediately.

Preventing Carbon Monoxide Poisoning

Never run engine indoors.

% Never try to ventilate engine exhaust indoors. Carbon mon-

oxide can reach dangerous levels very quickly.

Never run engine outdoors where exhaust fumes may be

pulled into a building.

Never run-engine outdoors in a poorly ventilated area

where the exhaust fumes may be trapped and not easily

taken away. (Examples include: in a large hole or areas



where hills surround your working area.)

Never run engine in an enclosed or partially enclosed area.

(Examples include: buildings that are enclosed on one or

more sides, under tents, car ports or basements.)

Always run the engine with the exhaust and muffler pointed

in the direction away from the operator.

Never point the exhaust muffler towards anyone. People

should always be many feet away from the operation of the -

engine and its attachments.

Gasoline Fires or Handling Fuel Safely

Fuel and fuel vapors are highly flammable. Never use fuel

where a spark or flame may be present. Never use fuel where

a potential source of ignition could occur. (Examples include:

hot water or space heaters, clothes dryer, electric motors, etc.)

Keep flames and sparks away from engine and fuel to prevent

fires. Fuel fires spread very quickly and are highly explosive.

Prevention of Gasoline Fires

Never fill your fuel tank with fuel indoors. (Examples in-

clude: basement, garage, barn, shed, house, porch, etc.)

Always fill fuel tank outside in a well ventilated area.

Never remove the fuel cap or add fuel with the engine run-

ning. Stop engine and allow to cool before filling.

Never drain fuel from engine in an enclosed area.

Always wipe up excess (spilled) fuel from engine before

starting. Clean up spilled fuel immediately.

Allow spilled fuel to dry, after wiping and before starting.

Allow fuel fumes/vapors to escape from the area before

starting engine.

Test the fuel cap for proper installation before starting and

using engine.

Always run the engine with fuel cap properly installed on

the engine and gas cap vent screw unscreWed..

Replace fuel cap that allows gas to spill or leak.

Never smoke while refilling engine fuel tank.

Prevent fire and explosion caused by static electric

discharge. Use only non-metal, portable fuel containers

approved by the Underwriter's Laboratory (U.L.) or the

American Society for Testing & Materials (ASTM).

;



Do not store engine with fuel in fuel tank indoors. Fuel and

fuel vapors are highly explosive.

When storing, screw down gas cap vent screw tightly.

Never pour fuel from engine fuel tank.

Never siphon fuel by mouth to drain fuel tank.

Always have an adult fill the fuel tank.

Never allow an adult or anyone under the influence of

drugs or alcohol to fill engine.

Never allow children to fill the engine.

BURNS AND FIRES

The muffler, muffler guard and other parts of the engine be-

come extremely hot during the operation of the engine. These

parts remain extremely hot after the engine has stopped.

Prevention of Burns and Fires

Never remove the muffler guard from the engine.

Never touch the muffler guard because it is extremely hot

and will cause severe burns.

Never touch parts of the engine that become hot after

operation._

Always keep materials and debris away from muffler guard

and other hot parts of the engine to avoid fires.

This engine is designed to operate using a catalytic converter

which contributes to the engine's compliance with the EPA.

Parts Online

Page 4

800-345-6007

Ardisayn.cpi,

IMPORTANT

THIS ENGINE USES A GAS/OIL MIXTURE. DO NOT

RUN ON STRAIGHT GAS ONLY, ENGINE DAMAGE

WILL RESULT.

CAUTION

NOT ALTER/MODIFY ENGINE OR AUGER:

AVOID INJURY! NEVER ALTER OR MODIFY THE

ENGINE FROM THE FACTORY. SERIOUS INJURY

OR DEATH MAY OCCUR IF ENGINE IS MODIFIED

OR ALTERED.

AVOID INJURY! WHEN WORKING ON OR REPLAC-

ING PARTS FOR THE ENGINE OR AUGER YOU

MUST ALWAYS DISCONNECT SPARK PLUG WIRE

FROM THE SPARK PLUG AND KEEP IT AWAY

FROM THE SPARK PLUG.

AVOID INJURY! ALWAYS WEAR HEARING PRO-

TECTION WHILE OPERATING ENGINE.

AVOID INJURY! PLEASE DO NOT START YOUR

EARTH AUGER UNTIL YOU HAVE READ THE PRE-

VIOUS SECTION OF THIS MANUAL. IF YOU HAVE

READ THESE, FOLLOW THE STEPS BELOW TO

START YOUR EARTH AUGER.

AVOID INJURY! NEVER STORE ENGINE WITH GAS

IN THE TANK INDOORS. FUEL AND FUEL VAPORS

ARE HIGHLY FLAMMABLE.

AVOID INJURY! NEVER MIX FUEL AND OIL DIRECT-

LY IN ENGINE GAS TANK. USE ONLY NON-METAL,

PORTABLE FUEL CONTAINERS APPROVED BY

THE UNDERWRITER'S LABORATORY (U.L.) OR

THE AMERICAN SOCIETY FOR TESTING & MATE-

RIALS (ASTM).

AVOID INJURY! AN ADULT MUST ALWAYS HANDLE

AND FILL THE ENGINE WITH FUEL.

AVOID INJURY! ALWAYS HANDLE FUEL IN A WELL

VENTILATED AREA, OUTDOORS, AWAY FROM

FLAMES OR SPARKS.

Earth

ualc

ASSEMBLY INSTRUCTIONS AND PARTS EXPLOSIONS r

E43 Model

OPERATION

STEPS FOR WORKING ON ENGINE OR AUGER

Turn off engine switch.

Disconnect the spark plug wire from the spark plug.

Securely place the disconnected spark plug wire away from the

spark.plug and any metal parts. This must always be done or

arcing may occur between spark plug wire and metal parts.

Replace or repair the part on the engine or auger.

Check all parts that were repaired, or removed during repair,

that they are secure and fit correctly.

NOTE: All repair parts must come from the factory. Never

replace parts that are not specifically designed for the

engine or auger.

Replace spark plug wire.

PREPARING ENGINE FOR STARTING

Before starting your powerhead engine, make sure the black throttle

cable housing is seated all the way into the brass ferrule at the

engine side of the cable.

GAS AND OIL

Quality

To operate the engine, we recommend using "VIPER" brand 2 cycle

oil (Pfi( 300400) to ensure that the engine operates correctly

throughout the life of the engine. Use unleaded regular gas only.

Mixture

Run earth auger with a 50:1 ratio.

GAS

OIL

RATIO

1 gallon

2.5 ounces

50:1

2 gallons

5 ounces

50:1

5 gallons 13 ounces

50:1

MIXING FUEL AND FILLING GAS TANK

Mixing Fuel

Fuel must be mixed in a container outside in a well ventilated

area.

Fill certified fuel container 1/4 full of recommended fuel.

Add recommended amount of 2 cycle oil.

Screw container cap on straight and tight.

Shake the container to mix fuel and oil.

Unscrew gas cap slowly to vent, add the remainder of fuel re-

quirements.

Wipe away any spilled fuel or oil and allow to evaporate before

moving or transporting.

800-345-6007

Parts Online

Page

Ardisam.com

8003454007 r

Page 6 „.

Parts Online

Earthauakt

ASSEMBLY INSTRUCTIONS AND PARTS EXPLOSIONS

E43 Model

Filling Gas Tank

Shut-off engine and allow engine to completely cool before refill-

ing the gas tank.

Move to a well ventilated area, outdoors, away from flames and

sparks.

Clean debris from area around the gas cap.

Loosen gas cap slowly Place the cap on a clean, dry surface.

Carefully add fuel without spilling.

do not fill gas tank completely full, allow space for fuel to ex-

pand.

Immediately replace gas cap and tighten. Wipe off spilled fuel

and allow to dry before starting engine.

NORMAL OPERATION

I. The clutch will transfer maximum

power after about

two hours

of normal operation. During this break-in period clutch slippage

may occur. The clutch should be kept free of oil or other mois-

ture for efficient operation.

Drill holes without placing excessive body weight on the unit.

The auger operates most efficiently with a shaving action

caused by the weight of the unit itself.

Never run engine indoors. Exhaust fumes are deadly.

Do not use an earth auger in the ice.

To attach auger to powerhead, align hole at top of auger shaft

with the output shaft hole. Insert 3/8-16 x 1

1/2" bolt and secure

bolt with provided 3/8" bi-way lock nut using a wrench.

USING THE SCREW TYPE, MANUAL VENTING GAS

CAP

Your power earth auger is equipped with a screw type, manual vent-

ing gas cap.

I. Before starting the engine, turn the screw in the top of the gas

cap all the way open (counterclockwise) to its venting position.

To ensure that gas will not spill during use, check that the gas

cap is screwed on tightly and the gas cap screw is in the venting

position.

2. After using the power earth auger and before putting away or

transporting it in a vehicle, screw the gas cap screw on (clock-

wise) tightly. This will prevent gas from leaking during storage.

The gas cap will not leak gas during storage if the gas cap is

tight and the screw at the top is tight.

NOTE: When storing unit in an upright position for pro-

longed periods of time in warm weather, vent gas cap to

prevent gas from leaking from carburetor.

CAUTION

AVOID INJURY! ALWAYS HANDLE FUEL IN A WELL

VENTILATED AREA, OUTDOORS, AWAY FROM

FLAMES OR SPARKS.



AVOID INJURY! DO NOT START ENGINE IF FUEL

IS SPILLED. WIPE OFF EXCESS FUEL AND ALLOW

TO DRY. REMOVE ENGINE FROM AREA TO AVOID

SPARKS.

Ardisam.conv

CAUTION

AVOID INJURY! ALWAYS HANDLE FUEL IN A WELL

VENTILATED AREA, OUTDOORS, AWAY FROM

FLAMES OR SPARKS.

AVOID INJURY! DO NOT START ENGINE IF FUEL

IS SPILLED. WIPE OFF EXCESS FUEL AND ALLOW

TO DRY. REMOVE ENGINE FROM AREA TO AVOID

SPARKS.

AVOID INJURY! IF AUGER IS MOUNTED TO EN-

GINE, ALL SAFETY GUARDS MUST BE SECURELY

ON TO AVOID SERIOUS INJURY.

AVOID INJURY! STARTER ROPE CAN CAUSE

AN UNANTICIPATED JERK TOWARDS ENGINE.

PLEASE FOLLOW INSTRUCTIONS TO AVOID IN-

JURY.

AVOID INJURY! IF ENGINE FAILS TO START AFTER

TRYING STARTING PROCEDURES, PLEASE CON-

TACT OUR CUSTOMER SERVICE DEPARTMENT AT

800-345-6007.

AVOID INJURY! NEVER LEAVE ENGINE RUNNING

WHILE UNATTENDED. TURN OFF AFTER EVERY

USE.

AVOID INJURY! NEVER CARRY POWERHEAD AND

AUGER BETWEEN HOLES WHILE ENGINE IS RUN-

NING.

WARNING

AVOID INJURY! MAKE SURE THE UNIT IS IN A STA-

BLE POSITION BEFORE PULLING THE STARTER

HANDLE.

AVOID INJURY! WHEN THE UNIT STARTS TO FIRE

OR RUN, RELEASE THE THROTTLE CONTROL

MOMENTARILY WITH YOUR RIGHT HAND AND RE-

TURN YOUR LEFT HAND TO THE HANDLEBAR PO-

SITION TO MAINTAIN CONTROL AND STABILITY

OF THE UNIT WITH BOTH HANDS.

_Earthauaice

ASSEMBLY INSTRUCTIONS AND PARTS EXPLOSIONS

E43 Model

STARTING AND STOPPING ENGINE

Move engine to a well ventilated area, outdoors, to prevent car-

bon monoxide poisoning.

Move to an area away from flames or sparks, to avoid ignition of

vapors if present.

Remove all debris from air cleaner holes and gas cap to ensure

proper air flow.

COLD ENGINE START:

Starting engine for first time or after engine

has cooled off or after running out of fuel.



Open gas cap vent screw all the way (counterclockwise).

Move choke lever to

RUN or OFF

position.

NOTE: Choke must be in the RUN or OFF position when

pushing or using the primer bulb.

Prime unit until primer hose is filled with gas.

NOTE: When using the primer bulb, allow the bulb to return

completely to its original position between pushes.

Move choke lever to

CHOKE or ON

position.

NOTE: CHOKE position is defined by moving the choke

lever as far to the ON position as possible.

Push rocker switch to the

position.

Squeeze throttle control with right hand. Grasp starter handle

with left hand and pull out slowly, until it pulls slightly harder.

Without letting starter handle retract, pull,rope with a rapid full

arm stroke. Let it return to its original position very slowly until

unit fires or runs. Repeat this step every time the starter rope is

pulled.

NOTE: If engine fails to start after 5-6 pulls, push primer I

time and pull starter rope again.

After engine starts running, move choke lever to

HALF CHOKE

position until unit runs smoothly.

NOTE: HALF CHOKE is defined when the choke lever is

between CHOKE and RUN or ON and OFF.

Move choke lever to

RUN or OFF

position and move throttle to

desired speed.

NOTE: Run at full throttle when possible. Do not let unit

idle for extended periods of time.

To stop engine, push rocker switch to

OFF

position.

WARM ENGINE START:

Open gas cap vent screw all the way (counterclockwise).

Move choke lever to

CHOKE or ON

position.

NOTE: CHOKE position is defined by moving the choke

lever as far to the ON position as possible.

Continue with Step 5 of Cold Engine Starting.

Parts Online

Ardisam.com

111.11111

800-345-6007

Page 7

Earthauaice

ASSEMBLY INSTRUCTIONS AND PARTS EXPLOSIONS

E43 Model

HOT ENGINE START:

Open gas cap vent screw all the way (counterclockwise).

Continue with Step 5 of Cold Engine Starting.

If engine does not fire, refer to Step 2 of Warm Engine Starting.

DO NOT attempt to start engine in the following ways'

DO NOT use starting fluid.

DO NOT spray flammable liquids or vapors into air cleaner,

carburetor or spark plug chamber.

•



DO NOT remove spark plug and pull on starter rope. Flam-

mable fuel can spray out & Ignite from a spark from spark

plug.

MAINTENANCE AND STORAGE

AUGER MAINTENANCE

The gear case has 4 oz. of grease installed at the factory. It is

recommended that once a year the gear case be split and the

grease level checked. Add grease only if level of grease is below

top of the gears.

DO NOT OVERFILL.

Keep all screws, nuts, and bolts tight.

For cold weather operation, store the unit in a cool environment.

Transferring the unit from a warm to a cold place can cause the

build up of harmful condensation.

If blade performance decreases, turn unit off and disconnect

spark plug wire. Carefully inspect cutting edge of blade for any .

signs of wear. If blades show any of these signs, they need to be

sharpened or replaced.

ENGINE MAINTENANCE

Cooling Fins

Cooling fins, air inlets and linkages must be free from any debris

before each use. '

Air Filter

Never run engine without air cleaner properly installed. Added wear

and engine failure may occur if air.cleaner is not installed on engine.

Service air cleaner every 3 months or after 20 hours of operation.

Clean fitter daily in extremely dusty conditions.

Steps for Cleanina Air Filter

Wash in warm water with mild soap until dirt and debrie are

removed. Press filter when washing, do not twist.

Rinse in warm water until soap and dirt are removed.

Dry filter by wrapping in a clean cloth and pressing filter until it is

dry.

Apply oil to the entire filter.

Remove excess oil.

Attach the fitter and air cleaner cover to the engine.

CAUTION

TO PREVENT ACCIDENTAL STARTING'

AVOID INJURY, ENGINE MUST BE TURNED OFF

AND COOL, AND SPARK PLUG WIRE MUST BE RE-

MOVED FROM SPARK PLUG BEFORE CHECKING

AND ADJUSTING ENGINE OR EQUIPMENT.

AVOID INJURY! TEMPERATURE OF MUFFLER AND

NEARBY AREAS MAY EXCEED 150° F. (65° C).

AVOID THESE AREAS.

AVOID INJURY! CHECK AUGER OFTEN FOR

LOOSE NUTS AND BOLTS. KEEP THESE ITEMS

TIGHTENED.

AVOID INJURY! NEVER STORE ENGINE WITH

FUEL IN THE TANK INSIDE A BUILDING. POTEN-

TIAL SPARKS MAY BE PRESENT FOR IGNITION

OF FUEL AND FUEL VAPORS.

AVOID INJURY! AN ADULT MUST ALWAYS DO

MAINTENANCE AND REPAIR ON ENGINE AND AU-

GER.

AVOID INJURY! ENGINE MUST BE SHUT-OFF,

COOL, AND SPARK PLUG WIRE REMOVED BE-

FORE ANY REPAIR OR MAINTENANCE CAN BE

DONE.

(

MINIER

Page 8

Parts Online

800-345-6007

Ardisam.corn

Earthauake

ASSEMBLY INSTRUCTIONS AND PARTS EXPLOSIONS

E43 Model

Spark Plug

The recommended spark plug is a NGK BM6A which cross refer-

ences to a Champion CJ8.



Check spark plug every 50 operating hours.

Disconnect the spark plug cap, and clean any debris from

around the spark plug area.

Remove spark plug and replace if any of the following occur; pit-

ted electrodes, burned electrodes, cracked porcelain, or deposits

around electrodes.

After analysis, seat spark plug and tighten with spark plug

wrench.

Reinstall original spark plug, tighten additional 1/2 turn.

Installing new spark plug, adjust spark plug gap to .030" and

tighten additional 1/8 — 1/4 turn .

NOTE: Loose spark plug may overheat and damage engine.

Over tightened spark plug may damage threads in the cylinder

head.

Carburetor

Never tamper with factory setting of the carburetor.

TRANSPORTING YOUR EARTH AUGER

Never transport engine inside an enclosed space or vehicle.

Fuel or fuel vapors may ignite causing serious injury or death.

If fuel is present in the fuel tank, transport in an open vehicle in

an upright position.

If an enclosed vehicle must be used, remove gas into an ap-

proved red fuel container.

DO NOT siphon by mouth.

Run engine to use up the fuel in the carburetor and fuel tank.

Always run engine in a well ventilated area. -

Wipe away any spilled fuel from engine and earth auger. Allow

to dry.

LONG TERM STORAGE

•

If your earth auger will not be used for more than one month, pre-

pare it for long term storage.

Steps for Long Term Storage

Add fuel stabilizer according to manufacturer's instructions.

Run engine for 10-15 minutes to ensure that the stabilizer reach-

es the carburetor.

Remove the remainder of the fuel from the gas tank into an ap-

proved fuel container.

Remove auger from powerhead and apply a thin layer of grease

to the output shaft (8913).

Store auger and powerhead (engine) in a vertical position.

Remove all debris from auger and powerhead (engine).

CAUTION

AVOID INJURYITO AVOID INJURY OR DEATH, NEV-

ER SIPHON FUEL BY MOUTH.

AVOID INJURY! NEVER STORE EARTH AUGER

WITH FUEL IN THE GAS TANK INSIDE AN EN-

CLOSED AREA OR BUILDING.

TO PREVENT ACCIDENTAL STARTING

AVOID INJURY! ENGINE MUST BE TURNED OFF

AND COOL, AND SPARK PLUG WIRE MUST BE RE-

MOVED FROM SPARK PLUG BEFORE CHECKING

AND ADJUSTING ENGINE OR EQUIPMENT.

AVOID INJURY! AN ADULT MUST ALWAYS DO

MAINTENANCE AND REPAIR ON ENGINE AND AU-

GER.

AVOID INJURY! ENGINE MUST BE SHUT-OFF,

COOL, AND SPARK PLUG WIRE REMOVED BE-

FORE ANY REPAIR OR MAINTENANCE CAN BE

DONE.

800-345-6007

Parts Online

Page 9

Ardisam. corn

Page 10

, •

Ardisam. corn

Earthauake

ASSEMBLY INSTRUCTIONS AND PARTS.EXPLOSIONS

E43 Model

SERVICE, TROUBLESHOOTING AND

REPAIR

SERVICE INFORMATION

At Ardisam, we build quality and durability into the design of our

products; but no amount of careful design by us, and careful main-

tenance by you, can guarantee a repair-free life for your auger. Most

repairs will be minor, and easily fixed by following the suggestions

in the troubleshooting guide in this section.

The guide will help you pinpoint the causes of common problems

and identify remedies.

For more complicated repairs, you may want to rely on your retailer,

an authorized mechanic or Ardisam, Inc. (contact your retailer for

a list Of authorized mechanics in your area). A parts catalog is

•

included in this section.

We will always be glad to answer any questions you have, or help

you find suitable assistance. To order parts or inquire about war-

ranty, call or write us at the address found below, under the section

ordering repair parts.

ORDERING REPAIR PARTS

Parts can be obtained from the store where your auger was pur-

chased or direct from the factory. To order from the factory, call or

write to:

Ardisam, Inc.

1690 Elm Street, Cumberland, Wisconsin 54829

1-800-345-6007 • 1-715-822-2415

E-mail: [email protected]

Please include the following information with your order:

Part numbers

Part description

Quantity

Model number and serial number

CAUTION

PRACTICE SAFETY AT ALL TIMES. ENGINE MUST

BE TURNED OFF AND ALLOWED TO COOL, AND

SPARK PLUG WIRE MUST BE DISCONNECTED

BEFORE ATTEMPTING ANY MAINTENANCE OR

REPAIR.

800-345-6007

Andere Handbücher für Earthquake E43

Inhaltsverzeichnis

Sprachen:

Andere Ardisam Werkzeuge Handbücher

Ardisam

Ardisam Earthquake E43 Bedienungsanleitung

Beliebte Werkzeuge Handbücher anderer Marken

Martor

Martor SECUNORM 175 Bedienungsanleitung

ERKCO

ERKCO 1000 Bedienungsanleitung

jbc

jbc N4473 Bedienungsanleitung

FEINMETALL

FEINMETALL FZWZ-SET-001 Bedienungsanleitung

Worx Professional

Worx Professional Sonicrafter WU676 Bedienungsanleitung

Gage Bilt

Gage Bilt GB713SH Bedienungsanleitung

Hilti

Hilti DX 9-ENP Bedienungsanleitung

norbar

norbar NORTRONIC 34399 Bedienungsanleitung

BGS technic

BGS technic 8578 Bedienungsanleitung

Makita

Makita DHR241 Bedienungsanleitung

Motor Guard

Motor Guard JMB-1250 Bedienungsanleitung

Power Adhesives

Power Adhesives 805-12 Bedienungsanleitung

Clemco

Clemco 24189 Bedienungsanleitung

VVG

VVG VNG 903 Series Bedienungsanleitung

Hilti

Hilti FX 3-A Bedienungsanleitung

Grizzly

Grizzly H6472 Bedienungsanleitung

axing

axing BWZ 5-02 Bedienungsanleitung

Dh-Robotics

Dh-Robotics RGI-100 Anleitung zur Verwendung