Argo Soul digit Bedienungsanleitung

V 05/16

OPERATING INSTRUCTIONS

Read the instructions carefully before installing and operating the appliance or performing

maintenance operations. Observe all the safety instructions; failure to observe the instructions may

cause accidents and/or damages. Store these instructions for future reference.

ELECTRIC CONVECTOR

V 05/16

GENERAL SAFETY INFORMATION

Use this convector only as outlined in this manual. Any other use

not recommended by the manufacturer may cause fire, electric

shock or injury to people.

Ensure that the mains power complies with the voltage specified on

the convector data plate (220-240V~/50Hz).

This appliance can be used by children aged from 8 years and

above and people with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have been

given supervision or instruction concerning use of the appliance in a

safe way and understand the hazards involved.

Children shall not play with the appliance.

Cleaning and user maintenance shall not be made by children

without supervision.

This product is not a toy. Children under the age of 3 years must be

kept out of reach unless properly supervised, to ensure that they do

not play with the appliance.

Children aged between 3 and 8 years must only be able to turn the

appliance on/off, provided that the appliance has been placed in its

normal operating position, that instructions have been given on how

to use the equipment safely, and that its risks have been

understood.

Children aged from 3 years and les than 8 years shall not plug in,

regulate and clean the appliance or perform user maintenance.

CAUTION - Some parts of this product can become very hot

and cause burns. Particular attention has to be given where

children and vulnerable people are present.

WARNING: In order to avoid hazard due to inadvertent resetting of

the thermal cut-out, this appliance must not be supplied through and

external switching device, such as a timer, or connected to a circuit

that is regularly switched on and off by the utility.

WARNING: do not use the fan heater with a controller or any

other external device that activates the appliance

automatically, as there may be a risk of fire if the fan heater is

covered or incorrectly positioned.

Do not restrict the air inlet and outlet grilles.

The appliance heats up slightly when in use. In order to avoid burns,

do not let bare skin touch hot surfaces.

V 05/16

Ensure that all objects are at least 1 meter from the front and sides

of the appliance.

Disconnect the mains power when the appliance is not used or for

cleaning operations.

Avoid using the convector in dusty environments or in the presence

of inflammable vapours (e.g. in workshops or garages) or paint

vapours.

Do not place anything on the appliance, use the appliance to dry

clothing. Use the appliance in a well-ventilated area.

Avoid placing fingers or foreign objects in the air inlet/outlet grilles,

as this may lead to electric shock or fire and may damage the

appliance.

To avoid the risk of fire, do not block the grilles or tamper with them

in any way while the convector operates.

Do not use the appliance if the cord or plug are damaged. If the

power supply cord is damaged, it must be replaced by the service

centre so as to avoid any safety risks.

Do not operate the appliance if it has fallen from a height or has

suffered damage in any way. Contact a service centre to examine

the appliance or perform any electrical or mechanical repairs.

The most common cause of overheating is the build-up of dust in

the appliance. Remove dust deposits by unplugging the appliance

and cleaning the air outlets and grilles with the aid of a vacuum

cleaner.

Do not use abrasive detergents for cleaning this appliance. Clean

the appliance with the aid of a damp (not wet) cloth rinsed in hot

soapy water. Always remove the plug from the mains socket before

cleaning.

To disconnect the convector, push the switch to OFF and remove

the plug from the socket. Pull on the plug only. Avoid pulling on the

cord when disconnecting the convector.

Do not place any objects on the cord and do not bend it.

It is not advisable to use extension cords, as these may overheat

and cause the risk of fire. Do not use a single extension cord to

operate multiple appliances.

Do not immerse the cord, plug or any other element of the appliance

in water or other liquids.

Do not touch the plug with wet hands.

Do not place the convector above or near another heat source.

V 05/16

WARNING: AVOID COVERING THE CONVECTOR TO PREVENT IT

FROM OVERHEATING.

The symbol below signals the above warning:

The convector may cause the risk of fire if, while in operation, is

covered by or comes into contact with inflammable material

including curtains, drapery, blankets, etc. KEEP THE CONVECTOR

AWAY FROM THESE MATERIALS.

Do not connect the appliance to the mains power before it has been

properly assembled and positioned.

Do not run the cord under carpets. Do not cover the cord with

blankets, carpets or similar materials. Place the cord far away from

busy areas or where it cannot be accidentally pulled-out.

Do not position the convector below a socket outlet.

Do not operate the appliance outdoors.

WARNING: do not use the convector with a controller or any

other external device that activates the appliance

automatically, as there may be a risk of fire if the convector is

covered or incorrectly positioned.

Do not operate the convector in close proximity to bathtubs,

showers, washbasins or pools.

Upon initial start-up, the convector may emit a slight, harmless

smell. This smell is a normal effect of the initial heating up of the

internal heating elements, and should not recur later on.

WARNING: DO NOT DEPEND ON THE ON/OFF BUTTON

SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER.

WHEN SERVICING OR MOVING THE CONVECTOR, ALWAYS

UNPLUG THE POWER CORD.

A convector has hot and arcing or sparkling parts inside. It must not

be used in potentially dangerous locations such as flammable,

explosive, chemical-laden or wet atmosphere.

Do not place the convector on soft surfaces, like a bed, where

openings may become blocked. Always place the convector on a

stable, flat, level surface when operating, to avoid the chance of the

convector overturning. Locate the power cord so the convector or

other objects are not resting on it.

Always unplug the convector when not in use.

In order to avoid accidents turn unit off if unattended.

In the event of any problems (abnormal noise or a strange smell)

V 05/16

switch off the appliance immediately, do not

attempt to repair it and take it to your local after sales service.

DESCRIPTION OF PARTS

FRONT VIEW

REAR VIEW

A. Air delivery/air intake grille

B. Feet

C. Side handles

D. Buttons and LCD display

E. Rear holes for wall mounting

F. Remote control

HOW TO INSTALL THE APPLIANCE

The convector can be used as portable appliance, after assembling the feet, or alternatively it can be wall-mounted

using the specific accessories supplied.

A. Portable use: how to assemble the feet supplied.

The convector is packed without feet. These must therefore be assembled before using the appliance.

Assemble the feet as shown in the figure and put the convector in an upright position. Position the unit on a flat,

stable surface. When you move the appliance, use its side handles.

MONTE I PIEDINI IN DOTAZIONE

V 05/16

B. Wall-mounting: how to mount the convector onto the wall.

The convector packaging contains all the accessories necessary for wall-mounting.

To wall-mount, proceed as follows.

1. Observe the minimum distances from the walls as

pointed out in the picture below.

2. Mark on the wall with a pencil the points where it is

necessary to make the holes in order to insert the Fishers.

3. Drill holes in the wall and insert the 4 Fisher rawlplugs. Screw up 2 of the 4 screws supplied into the 2 upper

rawlplugs, keep the head of the screws out of the Fisher rawlplugs for 8 mm.

4. Install the two spacers in the bottom of the convector as described in the picture.

5.Insert the hooks on the head of the screws, then tighten the screws firmly.

V 05/16

6. Insert the rear holes for wall mounting of the convector into the hooks on the wall, then fix the spacers at the

base of the convector.

V 05/16

HOW TO USE THE CONVECTOR

Position the unit on a flat, stable surface.

Connect the power cord to a suitable electric socket (220-240V~/50Hz).

When you move the appliance, use the handles.

LCD DISPLAY

CONTROL PANEL

Heating mode selection button

ECO/COMFORT/SUPER

Press this button and then the

buttons +/ – in order to select

the mode:

- ECO mode: reduced power to

save energy (750W).

- COMFORT mode: medium

power (1250W).

- SUPER mode: maximum power

(2000W).

TIMER button

When the appliance is operating, the operating time can be

set by touching this button: the timer display lights and

shows 0 and pressing the buttons +/- you can set the

desired time, between 0,5 and 24 hours, with each touch

corresponding to half an hour.

Press and hold the button + or - for 2 seconds in order to

increase/decrease the timer quickly.

The display shows the set time. The unit will switch off

automatically at the end of the programmed time.

In order to switch it on again press the button ON/OFF .

If a TIMER is set the LCD display shows the symbol .

Buttons + and -

Allow you to adjust the mode

(ECO, COMFORT, SUPER), the

temperature and timer settings of

the appliance.

ON/OFF button

Touching the ON/OFF button the

appliance will begin to operate and the

symbol appears on the LCD

display. Touching the button ON/OFF

once again the appliance will switch off

and the symbol disappears.

TEMPERATURE button

When the appliance is operating, touching this button will

allow you to set the temperature: the display will show

ambient temperature in °F and pressing again this

button in °C. Pressing the buttons + and - , the desired

temperature can be set between 5 and 37°C (41 – 99 °F).

Press and hold the button + or - for 2 seconds in order to

increase/decrease the temperature quickly. After 5” the

display will show the ambient temperature once again.

When the set temperature is 2°C below the room

temperature, the convector starts heating.

NOTE – The default temperature is 24°C –

75°F.

FORCED VENTILATION button

(TURBO function)

TIMER display FORCED

VENTILATION

display

TEMPERATURE

display

(°C or °F)

ECO/COMFORT/

SUPER mode

display

Convecto

symbol ON

display

Display on if the

room

temperature is

below 5°C

LED POWER ON: the power

supply is connected.

V 05/16

WARNING: ALWAYS UNPLUG THE APPLIANCE BEFORE CLEANING OR MAINTENANCE.

WHEN YOU TURN THE APPLIANCE ON AGAIN, AFTER SWITCHING IT OFF YOU HAVE TO RESET ALL

FUNCTIONS AGAIN.

REMOTE CONTROL

The remote control uses Lithium/Manganese button cells, model no. CR2025 -3 V, compliant with Battery Directive no.

2006/66/CE (supplied with the remote control).

HOW TO INSERT / REMOVE THE REMOTE CONTROL BATTERIES (refer to the diagram below)

Open the battery cover at the rear of the remote control (press and pull the cover).

Place the battery into the cover, observing the correct polarity. Insert the cover onto the remote control.

OVERHEATING SAFETY DEVICE

In case of overheating the safety cut out protecting the heating element will automatically switch off the convector.

In this case the convector stops working.

If this happens:

select SUPER mode (maximum power);

it the problem persists, switch off the convector;

remove the causes of abnormal operation or overheating (i.e. obstacles in front of air inlet or air outlet grille, abnormal

accumulations of dusts inside the appliance);

let the convector cool down for 15/20 minutes;

switch on again the convector and verify the correct operation.

If the fault persists, contact an Authorized Service Center.

ECO/COMFORT/SUPER

mode selection button FORCED

VENTILATION

button

ON/OFF button

+ and -buttons

TEMPERATURE button

TIMER button

Information for correct disposal of the battery in accordance with the European Directive 2006/66/EC

Please replace battery when its electricity charge is used up: please do not eliminate this battery together with normal

household waste. It must be taken to special local community waste collection centres or to a dealer providing this service.

Disposing of a battery separately avoids possible negative effects on the environment and human health deriving from an

inappropriate disposal and enables its components to be recovered and recycled to obtain significant savings in energy and

resources. In order to underline the duty to dispose of this equipment separately, the battery is marked with a crossed-out

dustbin.

V 05/16

MAINTENANCE AND STORAGE

ALWAYS UNPLUG THE APPLIANCE BEFORE CLEANING OR MAINTENANCE.

IMPORTANT: DO NOT SUBMERGE THE CONVECTOR IN WATER.

Cleaning the outside surface of the appliance

Turn the switch off and unplug before carrying out any maintenance work or moving the appliance.

Use a soft cloth to remove any dust from the convector.

If the convector is excessively dirty, use a soft cloth moistened with water and a mild detergent at a temperature lower

than 50°C. Let the convector dry completely before use.

Do not use corrosive detergents or solvents such as petrol. Do not wash the appliance with water. Do not use oils,

chemical substances or other items to clean that may damage the surface.

Use a vacuum cleaner to remove dust from the air inlet/outlet grilles.

STORAGE

If the appliance is not used for prolonged periods, it must be stored together with this manual in its original packaging, in a

cool and dry place.

INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH THE EUROPEAN DIRECTIVE

2012/19/EU

At the end of its working life this equipment must not be disposed of as an household waste. It must be taken to special local

community waste collection centres or to a dealer providing this service. Disposing of electrical and electronic equipment

separately avoids possible negative effects on the environment and human health deriving from an inappropriate disposal and

enables its components to be recovered and recycled to obtain significant savings in energy and resources. In order to underline

the duty to dispose of this equipment separately, the product is marked with a crossed-out dustbin.

www.argoclima.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Argo Heizung Handbücher

Argo

Argo WHISPER 9 Bedienungsanleitung

Argo

Argo Orange Bedienungsanleitung

Argo

Argo LOXO Bedienungsanleitung

Argo

Argo HI FAN Bedienungsanleitung

Argo

Argo CHIC SILVER Bedienungsanleitung

Argo

Argo HI FLOOR RAY Bedienungsanleitung

Argo

Argo MOOD Bedienungsanleitung

Argo

Argo HIFAN Bedienungsanleitung

Argo

Argo CREOLA Q3 Bedienungsanleitung

Argo

Argo HIFAN Black Bedienungsanleitung

Argo

Argo SPLITTO JR Bedienungsanleitung

Argo

Argo Soultt Bedienungsanleitung

Argo

Argo HI FAN black mini Bedienungsanleitung

Argo

Argo IP24 Bedienungsanleitung

Argo

Argo WILMA Bedienungsanleitung

Argo

Argo BETSY Bedienungsanleitung

Argo

Argo DAKOTA Bedienungsanleitung

Argo

Argo ARKE TOWER Bedienungsanleitung

Argo

Argo HiFan Digit Bedienungsanleitung

Argo

Argo MARGE Bedienungsanleitung

Argo

Argo Symphony Bedienungsanleitung

Argo

Argo Dream IP21 Bedienungsanleitung

Argo

Argo beatIP21 Bedienungsanleitung

Argo

Argo Sleek Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung

Argo soul digit Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken