ARGON18 E-117 TRI 285A Bedienungsanleitung
E-117 TRI 285A: ASSEMBLY GUIDE
Valid for MY2019 E-117 Tri 285A / 285B
Revision 1.1 - 07-04-2018
E-117 TRI 285B: ASSEMBLY GUIDE
Valid for MY2019 E-117 Tri 285A / 285B
Revision 1.1 - 07-04-2018
1. Tools Needed & First Ait Kit ..............................2
2. Frameset Parts ...........................................3
3. Parts’ SKUs and Descriptions .............................4
4. Seat Post Clamp Installation ..............................5
5. Seat Post Installation.....................................6
6. Frame Inspection ........................................8
7. Derailleur Hanger Adjustment ............................9
8. Headset Installation.....................................11
9. Cable Housing Installation ..............................14
10. Electronic Drive-train Specication .....................17
11. Front Brake Installation ................................20
12. Rear Brake Installation .................................23
13. Saddle Adjustment ....................................25
14. Troubleshooting/Tips ..................................26
15. Appendix..............................................27
For the warranty to be valid, the bicycle must be fully assembled by an authorized Argon 18 dealer. High end components,
particularly carbon parts, need extra care when assembled. These components must be installed using a calibered torque
wrench to make sure every bolt is at the right torque setting to prevent damage.
E-117 TRI 285A / 285B: Table of Contents
My E-117 Tri
Date of purchase:
Retailler:
Size:
Serial Number:
1
Tools needed for assembly
1: Bearing Cup Press (Park Tool HHP-2)
2: Allen Key Set
3: Grease
4: Utility Pick Set (Park Tool Item # UP-SET)
5: Clean Rags
6: Derailleur Hanger Alignment Gauge (Park Tool Item # DAG-2)
7: Cables and Housing Cutter
8: Carbon Paste
9: Loctite #242 or #243
10: Torque Wrench
First Aid Kit: Essential parts to always have on hand
IN CASE OF EMERGENCY…THIS MIGHT SAVE YOUR RIDE!
1: Spare rear dropout (SKU: 38883)
2: Spare brake pads corresponding to your wheel model (carbon or alloy)
3: Seat clamp (SKU: 80423, 80422)
IMPORTANT: the E-117 Tri’s seat clamp (1.4) is not the same as the Nitrogen
E-117 TRI 285A / 285B: 1. Tools Needed & First Aid Kit
2
SKU: 38883
1.6
RUNNING CHANGE
1.4.2 1.4.2
1.4.1 1.4.1
E-117 TRI 285A / 285B: 2. Frameset Parts
3
Included with 38882
FK.E117T.285A
FK.E117T.285B
SP.E117T.285A
80158
80774 80654
80096
80164
80372
80422
80373
80423
Included with 38882
running change
80264
38883
80167
38882
80160 8016580159
80424 80424
38879 36656 36670
36580
Images are for reference only. Proportions are not accurate.
Argon 18 reserves the right to modify/change parts of the frameset at any moment without prior notice.
*for more info please consult notice on Seatpost clamp dated 2016-06-09
E-117 TRI 285A / 285B: 3. Parts’ SKUs and Descriptions*
4
No. Name Assembled on A18 SKU # Qty
Parts already assembled
Parts
E-117 Tri Frame - - 1
E-117 Tri Fork - FK.E117T.285A 1
FK.E117T.285B
3 E-117 Tri ASP-7050 Seat Post - SP.E117T.285A 1
1.4.1 Seat Post Collar base (incl. screws) Frame 80423 1
1.4.2 Seat Post Collar wedge (incl. screws) Frame 80422 2
1.5 Top Tube Grommet (mechanical) Frame 36656 2
1.6 Top Tube Grommet (electronic) Frame 36670 2
1.8 Bottom Bracket Cover (incl. screws) Frame 80159 1
1.10 Rear Derailleur Cable Stopper (mechanical) Frame 80160 1
1.14 Plastic Plug Frame 80264 7
1.16 Front Derailleur Cable Grommet Frame 80164 1
1.17 Rear Derailleur Grommet (electronic) Frame 80165 1
3.2 Internal Di2 Battery Support Seat Post 80167 1 Set
4 Rear Brake Assembly (TKB138-3) Frame 80774 1
4.2 Brake Noodle (ts TKB137-2 & TKB138-3) - 80424 2
5 Front Brake Assembly (TKB137-2) Fork 80654 1
6 3D Headset Assembly Fork 80096 1
7 Jagwire Housing Kit Frame 39014 1
8 Brake Levers TL-720 - 36580 1 Set
1.2 Rear Derailleur Hanger (incl. screws) Frame 38883 1
1.3 Front Derailleur Hanger (incl. screws) Frame 38882 1
1.7 Bottom Bracket Cable Guide (incl. screws) Frame 80158 1
1.15 Cable Stopper Frame 38879 1
1.11 Bottle Cage & Front Derailleur Screws Frame incl. with 38882 7
*Except for the frame itself, which is not sold as a spare part, all parts can be ordered by referring to their respective SKU number.
5
E-117 TRI 285A / 285B: 4. Seat Post Clamp Installation
1. Place the seat post collar inside the
frame.
2. Insert the seatpost (3.1) on which
some carbon ber assembly paste has
been applied.
3. Position the seatpost to the desired
height.
4. Apply a drop of blue Threadlocker
(n. 242) on the bolt’s thread
5. Tighten the set screw at max. 5.5Nm
while leaving a space between the two
parts allowing them to slide.
IMPORTANT: The E-117 Tri+’s seat
clamp is not the same as the Nitrogen
GREASE
GREASE
THREADLOCKER
BLUE (n. 242)
LOCTITE
GREASE
CARBON FIBER
ASSEMBLY
COMPOSITE
5.5 Nm
1Nm
1.4.1
RUNNING CHANGE
1.4.1
6
E-117 TRI 285A / 285B: 5. Seat Post Installation
B
A
C
1. Unscrew main bolt (A) as far as
possible without fully removing from
the lock nut.
2. Install the saddle rails into the
seatpost clamp (B).
3. Slide saddle clamp (B) onto rocker (C).
4. Tighten the bolt up at 12Nm.
See p.25 for saddle adjustment.
IMPORTANT:
The E-117 Tri+’s saddle rail clamp is
made for aluminum and round-shaped
saddle rails (For part numbers contact
Ritchey).
For other types of saddle rails, please
refer to the Tips and Troubleshooting
section of this Assembly Guide (p.26).
12Nm
GRIP PASTE
GRIP PASTE
5Nm
5Nm
3.2
7
E-117 TRI 285A / 285B: 5. Seat Post Installation
The Di2 battery is hidden in the
seatpost; use the Di2 battery holder
(3.2) to x the battery correctly. Apply a
slight amount of grease on both parts.
GREASE
GREASE
8
E-117 TRI 285A / 285B: 6. Frame Inspection
Parts installed on the frame Description Screw Torque Detail
type Nm
Front derailleur hanger Screw (2) 5mm 4Nm Loctite
Rear derailleur hanger Screw (2) 3mm 4Nm Loctite
Bottle cage Screw (7) 4mm 3Nm Grease
Bottom bracket cover Screw (2) 4mm 2.5Nm Grease
IMPORTANT:
The following parts are assembled on the frame. When assembling the bike, you will need to adjust these parts according to their
torque specications.
1. Brakes and gears cables and housing set
2: Frameset parts checklist (see p.27)
3: Inspect the frame for cosmetic aspect (scratches, bumps, cracks, paint defect, etc.)
4: For reference, check serial number and write it on p.1
5: All the necessary bolts (refer to Frameset Parts, p.4)
6: For optimal shifting performance, use a dropout alignment gauge to make sure that the drive-side dropout is
straight.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere ARGON18 Fahrrad Handbücher
ARGON18
ARGON18 RADON 237A Bedienungsanleitung
ARGON18
ARGON18 E-119 TRI+ Bedienungsanleitung
ARGON18
ARGON18 nitrogen Bedienungsanleitung
ARGON18
ARGON18 E-Road Bedienungsanleitung
ARGON18
ARGON18 GALLIUM PRO 210A Bedienungsanleitung
ARGON18
ARGON18 NITROGEN PRO 230A Bedienungsanleitung
ARGON18
ARGON18 SUBITO Bedienungsanleitung
ARGON18
ARGON18 GALLIUM PRO DISC 246A Bedienungsanleitung
ARGON18
ARGON18 E-116 Bedienungsanleitung
ARGON18
ARGON18 GALLIUM 260A Bedienungsanleitung
ARGON18
ARGON18 GALLIUM DISC 280A Bedienungsanleitung
ARGON18
ARGON18 E-118 NEXT Bedienungsanleitung
ARGON18
ARGON18 ELECTRON PRO Bedienungsanleitung
ARGON18
ARGON18 MY2016 Nitrogen Pro Bedienungsanleitung
ARGON18
ARGON18 ELECTRON PRO 245A Bedienungsanleitung
ARGON18
ARGON18 GALLIUM 279A Bedienungsanleitung
ARGON18
ARGON18 Dark Matter Bedienungsanleitung
ARGON18
ARGON18 MY2016 Nitrogen Pro Bedienungsanleitung
ARGON18
ARGON18 E-117 TRI+ Bedienungsanleitung
ARGON18
ARGON18 KRYPTON PRO Bedienungsanleitung
