Xtracycle Stoker 2021 Bedienungsanleitung

stoker assembly Manual 2021

Record the serial number and the Shimano key number

which can be found on the label on the side of the box. Keep

these numbers in a secure place since they might be needed

in case somethig happens to your bike or you lose your

Shimano key. The serial number is the number under the bar

code next to "Frame No:". For the Stoker, this will start with

STK. The key number is the number under the bar code next

to "Key No:".

01 - Open the bike box

Look over the box for signs of shipping damage. If damage

is present, please take pictures in case a shipping damage

report needs to be filed.

Assembling the

xtracycle stoker

Tools needed

3 mm Allen wrench

4 mm Allen wrench

5 mm Allen wrench

6 mm Allen wrench

Snippers / scissors for cutting zip ties

10 mm socket wrench

Pedal wrench

Cut away the yellow zip ties holding the box closed.

Please note: We show the bike being assembled in a

bike stand but the bike can be assembled without one.

If assembling your bike without a stand, be sure the bike

stays upright and is not turned upside down as this can

interfere with the function of the hydraulic brakes.

Open the box.

Inspect the contents and look again for any signs of shipping

damage.

Remove the small parts box, the KickBack 3 and the seat

post and set these aside.

Cut the string attaching the rear of the bike to the end of the

box.

Remove all of the packaging from the seat post and saddle.

With the bike still in the box, install the seat post into the

frame. Use a 5 mm Allen wrench to tighten the seat post

clamp and secure the seat post in place.

10 - Install the front wheel

The rear wheel comes pre-installed. The front wheel is zip

tied to the bike frame. Cut these zip ties and remove the

wheel. Set the wheel aside nearby.

Remove the bike from the box and secure it in your bike

stand. Once in the stand, loosen the FreeLoader Too bag and

remove the U-Tubes.

Remove all padding and cardboard protection from the bike.

Remove the front axle from the front fork.

14 - Install the KickBack 3

Grab the KickBack 3 and needed hardware to install the

KickBack 3.

Install the front wheel onto the fork. Make sure the rotor rests

in between the brake pads. Reinstall the front axle using the

M6 Allen wrench.

the KickBack 3 mounting plate needs to be slid into these

brackets and then the mounting plate bracket bolt can be

threaded into the boss on the underside of the boom tube.

Start to thread one M5 bolt up from the bottom of the

KickBack mounting plate. Thread it far enough to keep the

KickBack attached to the frame. Do not fully tighten.

With the KickBack legs folded up, place both Xtracycle

U-bolts over the Xtracycle’s front bridge and through the

KickBack mounting plate. For the right side U-bolt and rear

threads of the left side U-bolt, thread on a washer and a nut.

For the front threads of the left side U-tube, an additional a

rectangular cutout is needed. Place the rectangular washer

over the U-bolt threads, then lightly thread on a washer and

nut.leg, then lightly thread on a washer and nut.

Moving the legs as necessary to allow for access to the

bolts, lightly snug all four nuts with a 10mm socket wrench.

Alternating between nuts can keep the KickBack from pulling

to one side or the other.

Put the legs into the down position and pull them towards

the front of the bike to ensure that the KickBack is rotated as

far forward as possible and centered on the boom tube.

Using your 5 mm Allen wrench, tighten the bolts on the

BoomStrap or the single bolt below to 3Nm.

Using the 10 mm socket wrench, fully tighten all four U-bolt

nuts. The installation of the KickBack is now complete.

22 - Adjust the front light

To adjust the front light, first rotate the light so that it is front

facing.

Tighten the pivot bolts and secure the M6 bolt on the fender

with your 5 mm Allen wrench and 10 mm socket wrench.

Once the handlebars are straight, tighten down the stem

bolts to 4-6 Nm.

Rotate the handlebar grips into a comfortable upright

position and secure into place using a 3 mm Allen wrench.

Loosen the stem faceplate bolts in order to center

handlebars onto the stem and to rotate them into the

upright position.

24 - Adjust the stem and handlebars

You will now be adjusting the front stem and handlebars.

Loosen the stem bolts and rotate the stem to a forward

facing position.

You will hear a click when the wire has been attached

completely.

31 - Installing the pedals

Identify the left (drive side) right (non-drive side) pedals by

the markings on the threaded axle. The drive side (the side

that the chain is on) is clockwise threaded, the non-drive

side is counter clockwise threaded. Install the pedals on the

appropriate side.

Tuck this wire into the wire wrap with the other cables to limit

the amount of wire dangling in front of the handlebars.

28 - Connecting the cycling computer

Place the wire hanging off the front of the handlebars into

the Shimano Cable Tool TL-EW300 which is located in the

small parts box. Holding the cable tool, connect the wire into

the handlebar computer.

Determine if you would like to have the U-tubes installed in

the wide setting (shown on the left side of the bike pictured

below) or the narrow setting (shown on the right side). In the

wide setting, the U-tubes will extend 6" out from the frame. In

the narrow setting, they will extend 5.25" out from the frame.

If you would like to switch the width setting

on your U-Tubes to narrow or wide:

Press the spring pin button in and push or pull the spring pin

elbow on the inside of the U-Tube until the spring pin button

pops out and into the setting hole. Needlenose pliers might

be needed to help with this.

Check to see if the U-tubes will fit into the frame. If they

comfortably slide into the holes, skip to step 36.

Narrow

setting

hole

Wide

setting

hole

32 - Install the U-Tubes

Before installing the U-Tubes, please take note that the

rear insertion end on each U-Tube is slightly longer than the

insertion end on the front end of the U-Tube.

Front

insertion

end

Rear

insertion

end

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Xtracycle Fahrrad Handbücher

Xtracycle

Xtracycle RFA Utility Bedienungsanleitung

Xtracycle

Xtracycle Freeradical Bedienungsanleitung

Xtracycle

Xtracycle Freeradical Bedienungsanleitung

Xtracycle

Xtracycle RFA Sport Bedienungsanleitung

Xtracycle

Xtracycle RFA 2021 Bedienungsanleitung

Xtracycle

Xtracycle Swoop 2021 Bedienungsanleitung

Xtracycle

Xtracycle RFA Bedienungsanleitung

Xtracycle

Xtracycle EdgeRunner Swoop Bedienungsanleitung

Xtracycle

Xtracycle Swoop 4ST1000 Bedienungsanleitung

Xtracycle

Xtracycle STOKER Bedienungsanleitung

Xtracycle

Xtracycle STOKER Bedienungsanleitung

Xtracycle

Xtracycle RFA Bedienungsanleitung

Xtracycle

Xtracycle SWOOP Bedienungsanleitung

Xtracycle

Xtracycle RFA Bedienungsanleitung

Beliebte Fahrrad Handbücher anderer Marken

RAMBO

RAMBO R1000X2M-FF-BFD Bedienungsanleitung

Vermeiren

Vermeiren SAFARI Bedienungsanleitung

Velec

Velec A2/36V Bedienungsanleitung

Coswheel

Coswheel A-ONE Bedienungsanleitung

Betzold

Betzold 97869 Bedienungsanleitung

Cervélo

Cervélo S3 2019 Bedienungsanleitung

Tenways

Tenways AGO X Bedienungsanleitung

Festo

Festo EGSC-BS-KF Stücklistenhandbuch

Gio Electric

Gio Electric H1 Volt Bedienungsanleitung

GOGOBEST

GOGOBEST GM30 Bedienungsanleitung

DAHON

DAHON CIAO - 2009 Bedienungsanleitung

Aprimatic

Aprimatic ONDA 500 Kurzanleitung

MV Agusta

MV Agusta Lucky Explorer GRAVEL Gebrauchsanweisung

Greyp

Greyp G6 Series Bedienungsanleitung

Babboe

Babboe Carve-E Bedienungsanleitung

Huka

Huka orthros Bedienungsanleitung

APRILIA

APRILIA DORSODURO 750 ABS 2015 Bedienungsanleitung

Alien

Alien E-Bike Bedienungsanleitung