Argos Athina 608/0804 Bedienungsanleitung

MADE IN

BRITAIN

Dimensions

Width - 50cm

Depth - 59cm

Height - 89.5cm

Athina - 500 Drawer Unit

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 1 - 05/01/10

Important - Please read these instructions fully before starting assembly

608/0804

608/0921

608/0866

608/0983

ALR2456

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs

approximately 34kgs.

Please lift with care.

• Check you have all the

components and tools listed on

pages 2 and 3.

• Remove all fittings from the

plastic bags and separate them

into their groups.

• Keep children and animals

away from the work area, small

parts could choke if swallowed.

• Make sure you have enough

space to layout the parts before

starting.

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

• Parts of the assembly will be

easier with 2 people.

Glue Safety - Take care when using glue, please follow the advice below

Skin contact: Remove contami-

nation by washing with soap and

water. This procedure should be

followed prior to aeting and

drinking.

Eye contact: Rinse immediately

with clean water for 15 minutes

and seek medical advice.

If swallowed: Seek medical

advice immediately.

Care and maintenance

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• From time to time check that

there are no loose screws on

this unit.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

Note: If required the next page

can be cut out and used as

reference throughout the

assembly. Keep this page with

these instructions for future

reference.

• We do not

recommend the

use of power

drill/drivers for

inserting screws,

as this could damage the unit.

Only use hand screwdrivers.

• Safety note: It is

recommended that this unit is

secured to a wall using the

brackets supplied.

• Dispose of all packaging

carefully and responsibly.

bracket supplied

Components - Panels

Please check you have all the panels listed below

80%

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Left Side (D0315A)

(870 X 570mm)

Back (X739)

(480 x 533mm)

Rail (D0321A)

(470 x 60mm) x 2

Plinth (D0322A)

(470 x 150mm)

Right Side (D0316A)

(870 x 570mm)

Top (D0338A)

(500 x 590mm)

2 3

Base (D0319A)

(470 X 499mm)

5 7

Back (X739)

(480 x 533mm)

Drawer Front (D0318A)

(497 x 176mm) x 4

8Drawer Back (W413BCK)

(422 x 120mm) x 4

9Left Drawer Side (W413LH)

(450 x 120mm) x 4

10 Right Drawer Side (W413RH)

(450 x 120mm) x 4

11 Drawer Base (T413)

(447 x 433mm) x 4

Please check you have all the fittings listed below

Tools required

Components - Fittings If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases

more fittings may be supplied than are required.

Wooden dowel (F22) x 12

Metal dowel (F901) x 18

D E F

G H I

Rule Scissors Hammer Eye protection

(when using a

hammer or drill)

Cross-head

screwdriver

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Door Buffer (F137) x 8 45mm Screw (F65) x 16

CR Runner x 4

CL Runner x 4

DR Runner x 4

DL Runner x 4

Electric drill

Large locking

nut (F900) x 10

Bracket (F945) x 4

25mm Screw (F50) x 2

13mm Screw (F79) x 1

13mm Screw (F63) x 3213mm Screw (F79) x 6

Nail (F51) x 8

Small locking

nut (F3) x 8

LHandle (F847a ) x 4

LHandle Screw (F847b) x 8

F426 x 1

F424 x 1 F425 x 1

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

80%

Prepare 4 drawer

fronts

Screw 2 metal dowels

into the holes shown on

the back of each drawer

front .

Note: Tighten metal

dowels up fully against

the panels.

Stick a drawer buffer

into the top corners of

each drawer front .

Prepare the drawer

sides

Insert a small locking

nut into the hole

shown on the left drawer

side and right drawer

side .

Note: Arrow on locking

nut must point towards

hole in edge of panel.

Assemble drawer

sides and back

Fit the left drawer side

and right drawer side

to the drawer back

using 4 screws .

Step 2

Step 3

Fit drawer base

Slide the drawer

base along the

grooves of the drawer

sides and into the

groove of the drawer

back .

9 10

Step 4

910

Fit the door buffers

Stick a drawer buffer

into the top corners of

each drawer front .

Assembly Instructions

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

Rebated Edge

F73

COVERED EDGE

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

F1004

When you insert F900,

make sure the arrow is

pointing towards the hole

in the edge of the panel.

F900

F73

F1004

COVERED EDGE

Step 5

Attach drawer front

Turn the drawer

assembly over and push

onto the back of the

drawer front .

Note: Turn locking

nuts clockwise to

secure panels - more

than 1/2 a turn.

Attach 2 handles

Attach each handle

to the drawer fronts

using 2 screws .

Step 6

Step 7

Fit runners to the

drawers

Turn the 4 drawer

assemblies over.

Fit runner ,marked

with ‘DR’, to the bottom

edge of the right drawer

side , making sure

that it is pushed up

against the back of the

drawer front . Use a

bradawl to mark the

fixing positions, then

secure with 2 screws .

Fit runner , marked

‘DL’, to the bottom edge

of the left drawer side

using the same method.

M c

L b

L a

M d

M c

M d

L a

L b

Assembly Instructions

Step 8

Step 9

Fit runners to the left

side

Fit the 4 runners

marked ‘CL’ to the left

side .

The 1st screw uses

the 2nd hole in from the

front of the runner.

The 2nd screw uses

the 6th hole in from the

back of the runner.

Step 10

Fit metal dowels to

the left side

Screw 5 metal dowels

into the holes shown on

the left side .

Note: Tighten metal

dowels up fully against

the panels.

Fit 2 brackets to the

left side

Fit a bracket to the

left side , 100mm in

from the back edge, see

diagram.

Fit another bracket to

the left side , 100mm

down from the top edge,

see diagram.

Secure each bracket

using screw .

Note: The brackets must

be flush with the edges

of the panel.

100mm

M b

ICL

Assembly Instructions

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

Rebated Edge

F73

COVERED EDGE

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

F1004

When you insert F900,

make sure the arrow is

pointing towards the hole

in the edge of the panel.

F900

F73

F1004

COVERED EDGE

Step 11

Step 13

Fit metal dowels to

the right side

Screw 5 metal dowels

into the holes shown on

the right side .

Note: Tighten metal

dowels up fully against

100mm

Fit 2 brackets to the

right side

Fit a bracket to the

right side , 100mm

down from the back

edge, see diagram.

Fit another bracket to

the right side ,

100mm down from the

top edge, see diagram.

Secure each bracket

using screw .

Note: The brackets must

be flush with the edges

of the panel.

M a

Step 12

Fit runners to the

right side

Fit the 4 runners

marked ‘CR’ to the right

side .

The 1st screw uses

the 2nd hole in from the

front of the runner.

The 2nd screw uses

the 6th hole in from the

back of the runner.

M a

Assembly Instructions

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

Rebated Edge

F73

COVERED EDGE

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

F1004

When you insert F900,

make sure the arrow is

pointing towards the hole

in the edge of the panel.

F900

F73

F1004

COVERED EDGE

Step 14

Finished

front edge

Prepare the base

Insert 4 large locking

nuts into the base

as shown.

Note: Arrow on locking

nut must point towards

hole in edge of panel.

Tap 6 wooden dowels

into the base as

shown.

Note: Wooden dowels

must not stick out from

the edge by more than

10mm or they may

damage other panels.

Step 15

Fit the base to the

right side

Push the base onto

the right side .

Use a screwdriver to

tighten the 2 large

locking nuts fitted to

the base .

Note: Turn the large

locking nuts as far as

they will go - more than

1/2 a turn.

Step 16

10mm

Prepare the 2 rails

and plinth

Insert 2 large locking

nuts into each of the

2 rails and plinth

as shown.

Tap 2 wooden dowels

into the 2 rails and

plinth as shown.

Polystyrene

block

Assembly Instructions

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

Rebated Edge

F73

COVERED EDGE

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

F1004

When you insert F900,

make sure the arrow is

pointing towards the hole

in the edge of the panel.

F900

F73

F1004

COVERED EDGE

Step 17

Step 7

Fit the top

Note: To make it easier

to fit the top panel, place

polystyrene blocks from

the packaging

underneath the side

panels to raise the

assembly.

Position the top onto the

unit, making sure that

the back edge of the top

is flush with the back

edge of the sides.

Secure the top using

screw through the 2

brackets fitted at the top

edge of the side panels.

F100mm

100mm

500mm

Fit the 2 rails and

plinth

One at a time, push the 2

rails and plinth

onto the right side as

shown.

Use a screwdriver to

tighten the 3 large

locking nuts fitted to

the 3 panels, as shown.

Note: Turn the large

locking nuts as far as

they will go - more than

1/2 a turn.

Note: Support the rail

near the back edge of

the unit until the left side

has been fitted in the

next stage.

5 6

Step 18

Fit the left side

Push the left side

onto the assembly.

Use a screwdriver to

tighten the 5 large

locking nuts fitted to

the base , rails

and plinth .

Note: Turn the large

locking nuts as far as

they will go - more than

1/2 a turn.

Support

this rail

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Argos Inneneinrichtung Handbücher

Argos

Argos Wow Leo 167/9605 Bedienungsanleitung

Argos

Argos Gabe Bedienungsanleitung

Argos

Argos Linear 247/6216 Bedienungsanleitung

Argos

Argos 487/8317 Bedienungsanleitung

Argos

Argos Verona 610/3475 Bedienungsanleitung

Argos

Argos Double Tidy Rail Bedienungsanleitung

Argos

Argos Kids Sywell 246/7634 Bedienungsanleitung

Argos

Argos Montana 395/6883 Bedienungsanleitung

Argos

Argos 600/1986 Bedienungsanleitung

Argos

Argos Half Width Tall Extra Deep Bookcase Bedienungsanleitung

Argos

Argos Maximus 606/5472 Bedienungsanleitung

Argos

Argos SEAGRASS CHEST 424/3801 Bedienungsanleitung

Argos

Argos 719/3594 Bedienungsanleitung

Argos

Argos Foley 360/3679 Datenblatt

Argos

Argos Hallingford 305/2811 Bedienungsanleitung

Argos

Argos Lawson 402/4439 Bedienungsanleitung

Argos

Argos Osaka Dressing Table 2273237 Bedienungsanleitung

Argos

Argos RONDA 8 SEATER CORNER DINING SET 7473441 Bedienungsanleitung

Argos

Argos Puerto Rico Bedienungsanleitung

Argos

Argos Savannah 602/5326 Bedienungsanleitung

Argos

Argos Cheval 147/8985 Bedienungsanleitung

Argos

Argos 875/4860 Bedienungsanleitung

Argos

Argos 609/2263 Bedienungsanleitung

Argos

Argos 831/9188 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung