Argos FS-CG-140X140X80 Bedienungsanleitung

105W PALM SANDER

INSTRUCTION MANUAL

FS-CG-140X140X80

ORIGINALINSTRUCTIONS

HELPLINE NO 08454 505299

ORIGINALINSTRUCTIONS

GENERAL POWER TOOL

SAFETY WARNINGS

WARNING: Read all safety

warnings and all instructions.

Failure tofollow the warnings and

instructions may result in electric shock, fire

and/or serious injury.

Save all warnings and instructions for

future reference.

The term “power tool” in the warnings

refers to your electric (corded) power tool or

battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do notoperate power toolsin

explosive atmospheres, such as in the

presence of flammableliquids, gases

or dust.Power tools create sparks which

may ignite the dust or fumes.

c) Keep children and bystanders

away whileoperating apower tool.

Distractions can cause you to lose

control.

2) ELECTRICALSAFETY

a) Power tool plugs must match the

outlet. Never modify the plug in

any way. Do notuse any adapter

plugswith grounded power tools.

Unmodified plugs and matching outlets

will reduce risk of electric shock.

b) Avoid body contact with grounded

surfaces, such as pipes, radiators,

ranges and refrigerators.There is an

increased risk of electric shock if your

body is grounded.

c) Do not expose power tools to rain

or wet conditions. Water entering a

power tool will increase the riskofelectric

shock.

d) Do not abuse the cord. Never use

the cord for carrying, pulling or

unplugging the power tool. Keep cord

away from heat, oil, sharp edges or

moving parts.Damaged or entangled

cords increase the risk of electric shock.

e) When operating apower tool

outdoors, use an extension cord

suitable for outdooruse. Use of acord

suitable for outdoor use reduces the risk

of electric shock.

f) If operating apower tool in adamp

location isunavoidable, use a residual

current device (RCD) protected

supply. Use of an RCD reduces the risk

of electric shock.

3) PERSONALSAFETY

a) Stay alert, watch what you are

doing and use common sense when

operating apower tool. Do notuse

apower tool while you are tired or

under the influence ofdrugs, alcohol

or medication. A moment of inattention

while operating power tools may result in

serious personal injury.

b) Use personal protective equipment.

Always wear eye protection.Protective

equipment such as dust mask,

non-skid safety shoes, hard hat, or

hearing protection used for appropriate

conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure

the switch isin the off-position before

connecting to power source and/or

battery pack, picking up or carrying

the tool. Carrying power tools with your

finger on the switch or energising power

tools that have the switch on invites

accidents.

d) Remove any adjusting key orwrench

before turning the power tool on.A

wrench or a key left attached to a rotating

part of the power tool may result in

personal injury.

e) Do notoverreach. Keep proper

footing and balance at all times. This

enables better control of the power tool in

unexpected situations.

f) Dress properly. Do notwear loose

clothing orjewellery. Keep your

hair, clothing and gloves away from

moving parts.Loose clothes, jewellery

or long hair can be caught in moving

parts.

g) Ifdevices are provided for the

connection ofdust extraction and

collection facilities, ensure these are

connected and properly used. Use of

dust collection can reduce dust-related

HELPLINE NO 08454 505299

ORIGINALINSTRUCTIONS

hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use

the correct power tool for your

application. The correct power tool will

do the job better and safer at the rate for

which it was designed.

b) Do notuse the power tool if the

switch does not turn iton and off.Any

power tool that cannot be controlled with

the switch is dangerous and must be

repaired.

c) Disconnect the plug from the power

source and/or the battery pack from

the power tool before making any

adjustments, changing accessories,

or storing power tools. Such preventive

safety measures reduce the risk of

starting the power tool accidentally.

d) Store idlepower toolsoutof the reach

of children and do not allow persons

unfamiliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands

of untrained users.

e) Maintain power tools. Check for

misalignment orbinding of moving

parts, breakage ofparts and any other

condition that may affect the power

tool’s operation. If damaged, have

the power tool repaired before use.

Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with

sharp cutting edges are less likely to bind

and are easier tocontrol.

g) Use the power tool, accessories and

tool bits etc. in accordance with these

instructions, taking into account the

working conditions and the work to

be performed. Use of the power tool for

operations different from those intended

could result in a hazardous situation.

5) SERVICE

a) Have yourpower tool serviced by a

qualified repair person using only

identical replacement parts.This will

ensure that the safety of the power tool is

maintained.

b) If the replacement of the supply cord

is necessary, thishas to bedoneby

the manufacturer orhis agent in order

to avoid a safety hazard.

ADDITIONAL SAFETY

RULES FOR YOUR SANDER

1. Use the machine only for dry sanding.

Penetration of water into the machine

increases the risk of an electric shock.

2. Pay attention that no persons are put

at risk through sparking. Remove any

combustible materials in the vicinity.

Sparking occurs when sanding metal

materials.

3. Caution, fire hazard! Avoid overheating

the object being sanded as well as the

sander.

4. Always empty the dust box before taking

breaks. In unfavorable conditions, e.g.,

when sparks emit from sanding metals,

sanding debris in the dust box, micro

filter or paper sack (or in the filter sack

or filter of the vacuum cleaner) can

self-ignite. Particularly when mixed with

remainders of varnish, polyurethane or

other chemical materials and when the

sanding debris is hot after long periods

of working.

5. When working with the machine, always

hold it firmly with both hands and provide

for a secure stance. The power tool is

guided more secure with both hands.

6. Secure the work piece. A work piece

clamped with clamping devices or in a

vice is held more secure than by hand.

7. Keep your workplace clean. Blends of

materials are particularly dangerous.

Dust from light alloys can burn or explode.

8. Never use the machine with a damaged

cable. Do not touch the damaged cable

and pull the mains plug when the cable is

damaged while working. Damaged cables

increase the risk of an electric shock.

HELPLINE NO 08454 505299

ORIGINALINSTRUCTIONS

WARNING: Some dust particles

created bypower sawing, contain

chemicals known to cause cancer, birth

defects orother reproductive harm.

Some examples of these chemicals are:

•Lead from lead-based paints.

•Crystalline silica from bricks and cement

and other masonry products.

•

Arsenic and chromium from chemically

treated lumber.

Your risk from these exposures varies,

depending upon how often you do this type

of work. To reduce your exposure tothese

chemicals:

•Work in a well-ventilated area.

•Work with approved safety equipment,

such as those dust masks that are

specially designed to ﬁlter microscopic

particles.

SYMBOLS

To reduce the risk of injury,

user must read instruction

manual

Warning

Double insulation

Wear eye protection

Wear ear protection

Wear dust mask

Waste electrical products

should not be disposed

of with household waste.

Please recycle where facilities

exist. Check with your local

authorities or retailer for

recycling advice.

HELPLINE NO 08454 505299

ORIGINAL INSTRUCTIONS

COMPONENT LIST

1. Sanding pad

2. On/Off switch

3. Dust extractor connection

4. Dust port

CHECK THE DELIVERY PARTS

Carefully remove the machine from its packaging and check

as the following parts are complete:

-- Palm sander

-- Sandpaper x 3

-- dust port

-- operating instructions

If any parts are missing or damaged, please contact your

dealer.

HELPLINE NO 08454 505299

ORIGINALINSTRUCTIONS

TECHNICAL DATA

Voltage230-240V~50Hz

Power 105W

Rated speed13000/min

Pad size:

Protection class

140x140x80mm

/II

Machine weight0.9kg

NOISE INFORMATION

A weighted sound pressure 72dB(A)

A weighted sound power 83dB(A)

KPA & KWA 3dB(A)

Wear ear protection when sound pressure is over 80dB(A)

VIBRATION INFORMATION

Vibration total values (triax vector sum) determined according toEN 60745:

Vibration informationVibration emission value ah = 16.468 m/s2

Uncertainty K= 1.5m/s²

WARNING: The vibration emission value during actual use of the power tool can

differ from the declared value depending on the ways in which the tool is used

dependant on the following examples and other variations on how the tool is used:

How the tool is used and the materials being cut or drilled.

The tool being in good condition and well maintained.

The use the correct accessory for the tool and ensuring it is sharp and in good condition.

The tightness of the grip on the handles and if any anti vibration accessories are used.

And the tool is being used as intended by its design and these instructions.

This tool may cause hand-arm vibration syndrome ifits use isnot adequately

managed.

WARNING: To be accurate, an estimation of exposure level in the actual conditions

of use should also take account of all parts of the operating cycle such as the times

when the tool is switched off and when it is running idle but not actually doing the job. This

may signiﬁcantly reduce the exposure level over the total worki

Helping to minimise your vibration exposure risk.

Maintain this tool in accordance with these instructions and keep well lubricated (where

appropriate).

If the tool is to be used regularly then invest in anti vibration accessories.

Avoid using tools in temperatures of 10 C or less.

Plan your work schedule tospread any high vibration tool use across a number of days.

ng period.

HELPLINE NO 08454 505299

ORIGINALINSTRUCTIONS

OPERATING INSTRUCTIONS

NOTE: Before using the tool, read the

instruction book carefully.

INTENDED USE

The machine is intended for dry sanding of

wood, plastic, metal, Filler as well as coated

surfaces.

Fig.A

Important!

Keep the cooling vents on the motor

housing clean and unobstructed at all

times. To be able to make the best use

of the sander, always use original spare

parts and accessories, available from

all specialist retailers. Align the holes in

the sandpaper with the dust extraction

holes in the base of your sander.

3. Connect the dust port

Important! In the interests of your health,

always use the dust extraction device

when sanding.

Connect the extract adaptor to the dust

extractor connection.

ASSEMBLY

1. Selecting the right grade of sandpaper

WARNING. Always ensure that the tool is

switched off and the plug is removed from

the power point before making any

adjustments or undertaking maintenance

procedures.

• Different grades of sandpaper can be

purchased from your local hardware store.

Available grades are: Coarse, Medium and

Fine.

• Use a coarse grit to sand down rough

finishes, medium grit to smooth the work

and fine grit to finish off.

• It is best to make a trial run on a scrap piece

of material to determine the optimum grades

of sandpaper for a particular job. If there are

still marks on your work after sanding, try

either going back to a coarser grade and

sanding the marks out before recommencing

with the original choice of grit ,or try using a

new piece of sandpaper to eliminate the

unwanted marks before going on to a finer

grit and finishing the job.

WARNING. Do not use the same sanding

sheet for wood and metal. Metal particles

become embed in the sandpaper and will

scour a wooden surface.

2. Fitting the sand paper

To fit the sand paper :

Disconnect the plug from the electricity supply.

Fix one side of the sandpaper, flush with one

side of the backing pad, then attach the

sandpaper to the backing pad and press it

firmly into place.

OPERATION

1. Starting Operation

Observe correct mains voltage! The voltage

of the power source must match

the voltage specified on the

technical plate of the machine.

2. Switching On and Off

Switch on:

Press ON/OFF switch. at the position “I”

HELPLINE NO 08454 505299

ORIGINALINSTRUCTIONS

Switch off:

Press ON/OFF switch at the position ”O”

changing the orbital stroke rate,

the sanding plate stroke rate can be reduced

whereby the orbital action is maintained.

With moderate pressure, move the machine

in a circular pattern or alternately in lengthwise

and crosswise directions over the work piece.

Do not tilt the machine to avoid sanding

through the work piece (e.g. when sanding

veneer)

MANITANCE AND SERVICE

Maintenance and Cleaning

• Before undertaking any work on the machine

itself, pull the mains plugunplug the power

supply.

• For safe and proper workingoperation, always

keep the machine and ventilation slots clean.

• Regularly check to see if any dust or foreign

matter has entered the grills near the motor

and around the on/off switch. Use a soft brush

to remove any accumulated dust.

• Wear safety glasses to protect your eyes

whilst cleaning.

• If the body of the tool needs cleaning, wipe it

with a soft damp cloth. A mild detergent can

be used but nothing like alcohol, petrol or

other such cleaning agents.

• Never use caustic agents to clean plastic part.

• Lubricate all moving parts at regular intervals.

CAUTION Water must never come into contact

with the tool.

Working Advice

Wait until the machine has come to a stand

still before placing it down on any surface.

2. Sanding Surfaces

Switch the machine on, place it with the

complete sanding surface on the surface to

be worked and move the machine with

moderate pressure over the work piece.

The removal capacity and the sanding

pattern are mainly determined by the

selection of the sanding sheet, and the

applied pressure.

Flawless sanding sheets will optimize

sanding capability and extend the service

life of the machine.

Apply uniform sanding pressure; this

increases the working life of the sanding

sheets.

Intensifying the sanding pressure does not

lead to an increase of the sanding capacity,

but to increased wear of the machine and

the sanding sheet.

A sanding sheet that has been used for

metal should not be used for other materials.

Use only original sanding accessories.

3. Rough Sanding

Attach a sanding sheet with coarse grain.

Apply only light pressure to the machine so

that it runs at a higher stroke rate and high

material removal is achieved.

4. Fine Sanding

Attach a sanding sheet with fine grain.

By lightly varying the application pressure or

HELPLINE NO 08454 505299

ORIGINALINSTRUCTIONS

PLUG REPLACEMENT

Your Power Tool is supplied with a ﬁtted

plug, however if you need to ﬁt a new plug

follow the instruction below.

IMPORTANT

The wires in the mains lead are coloured in

accordance with the following code:

Blue= Neutral Brown = Live

As the colours of the wires in the mains

lead of this appliance may not correspond

with the coloured markings identifying the

terminals in your plug, proceed as follows:

The wire which is coloured blue must be

connected tothe terminal which is marked

with N.

The wire which is coloured brown must be

connected tothe terminal which is marked

with the letter L.

If a 13 AMP (BS 1363/A)Plug is used, a

13 AMP Fuse must be ﬁtted, or if any other

type of plug is used a 13 AMP Fuse must be

ﬁtted, either in the Plug or Adaptor, or on the

Distribution Board.

Note:If a moulded plug is ﬁtted and has to

be removed take great care in disposing

of the plug and severed cable, it must

be destroyed to prevent engaging into a

socket.

If the supply cord is damaged it must be

replaced by a service agent or a similarly

qualiﬁed person in order to avoid hazard.

HELPLINE NO 08454 505299

ORIGINALINSTRUCTIONS

DISPOSAL

Do not dispose of electrical appliances with your domestic waste! The packaging comprises

exclusively environmentally- friendly material. Dispose of it in your local recycling containers.

General inspection.

Regularly check that all the fixing .They may vibrate loose over time.

GUARANTEE

This product is selected for DOMESTIC USE ONLY and not for business use. This product

is guaranteed against manufacturing defects for a period of 12 months. This does not cover

the product where the fault is due to misuse, abuse, use in contravention of the instructions,

or where the product has been the subject of unauthorised modifications or alterations, or

has been the subject of commercial use. In the event of a problem with the product within

the guarantee period please contact the service centre for assistance on 08454 505299. If

the item is shown to have an inherent defect present at the time of sale, you will be provided

with a replacement. Your statutory rights remain unaffected.

Guarantor: Home Retail Group, MK9 2NW

Inhaltsverzeichnis

Andere Argos Sander Handbücher

Argos

Argos PGF105P Bedienungsanleitung

Beliebte Sander Handbücher anderer Marken

Oliver

Oliver 6305 Bedienungsanleitung

Jet

Jet 22-44 Pro-3 Service-Handbuch

Makita

Makita M9204 Handbuch

Makita

Makita M9204 Bedienungsanleitung

Clarke

Clarke Woodworker CBS1-5B Bedienungsanleitung

Chicago Pneumatic

Chicago Pneumatic CP9778 Bedienungsanleitung

Nitto Kohki

Nitto Kohki BB-20 Bedienungsanleitung

Ferm

Ferm FEOS-135 Bedienungsanleitung

Unior

Unior 1510 Bedienungsanleitung

stayer

stayer ls1200 Bedienungsanleitung

Jet

Jet JSG-96 Service-Handbuch

Parkside

Parkside PDS 290 B2 Bedienungsanleitung

Status

Status XPA Series Bedienungsanleitung

Clarke

Clarke EZ Sand Bedienungsanleitung

Craftsman

Craftsman 113.22521 Bedienungsanleitung

Craftsman

Craftsman 113.225831 Bedienungsanleitung

CLAS

CLAS OP 1429 Bedienungsanleitung

Parkside

Parkside PEXS 270 Al Bedienungsanleitung