Argox AS-8512 Bedienungsanleitung

User’s Manual

Argox

Handheld Bar Code

Scanner

Model No.: AS-8510

USINGAS-8510/8512 RADIO CRADLE

TheAS-8510/8512 radio cradle paired with one

AS-8510/8512 scanner, builds a Cordless Reading

System for the collection, decoding and transmission

of barcoded data.

It can be connected to a Host PC through an RS232,

Keyboard wedge or USB cable and is suited for a

single-cradle layout.

The LEDs signal of the AS-8510/8512 radio cradle

status, asdescribed in the following:

BATTERY:

-Green LED blinking: thebatter charge is in

progress.

-Green LED On: the battery is completely charged.

TRANSMISSION:

-Green LED On: the radio cradle is powered.

-Orange LED blinking: the radio cradle receives

data and commands from the Host or the

scanner.

CONNECTING AND DISCONNECTING

THE RADIO CARDLE INTERFACE

CABLE

The radio cradle can be connected to a Host by

means of an RS232, Keyboard wedge or USB cable

which must be simply plugged into the Host connector,

placed on the base of the cradle. In addition the cradle

must be connected to an external power supply.

To disconnect the cable, insert a paper clip or other

small similar object into the hole at the back of the

cradle. Push down on the clip while unplugging the

cradle.

Default setting

For each barcode shown as below:

Read

Enable

CodeType

8510

8512

Checksum

Verification

Enable

Checksum

Transmission

Enable

Code

UPC-AVV

VVA

UPC-EVV

VVE

EAN-13 VV

VVF

EAN-8VV

VVFF

Code-39 VV

Interleaved

2 of 5 VV

Industrial

2 of 5 --i

Matrix 2 of 5 B

Codabar %

Code-128 VV

Code-93 V two digits

Code-11 VOne digit

MSI/Plessey V@

UK/Plessey V@

Telepen S

Standard 2 of 5

VVi

China Post t

Italian

Pharmacode.

Code-16K V(8512) --

PDF417 V(8512) --

EAN UCC

Composite --RC

Depth-head 35 mm

Weight Less than 250g (with a battery)

ArgoScan 8510/8512

Specification Model 8510 / 8512

Operational

Light Source 635 nm Visible Red LED

Optical System 2048 pixel CCD

(Charge-coupled device)

Depth of Scan Field

Up to 600mm (CODE 39, PSC=90%,

20mils)

Scanning Width 160mm

Scan Speed 400 scans/sec

Resolution 0.1mm(4mils) Code39,PCS=90%

Print Contrast 25% or more

ScanningAngle Front: 60° Rear: 60° Yaw: 70°

Decode Capability

Autodiscriminates all standard

barcodes;Other symbologies can be

ordered optionally (2D symbologies for

8512 only)

Beeper Operation

7 tones or no beep

Indicator Green & Red led

Mechanical

Length 164 mm

Width-handle 30 mm

Width-head 78 mm

Depth-handle 56 mm

Case material ABS (over molded at contact pointed)

Cushion material Double injection

Cradle interface RS232, Keyboard wedge, USB

Electrical

Input Voltage

(Cradle) 5 VDC ± 10% VDC

Power -Operating

(Cradle) 5 VDC

Power –Standby

(Cradle) 5 VDC

Current –Operating

(Cradle) 132 mA

Current –Standby

(Cradle) 132 mA

Charge Current

(Cradle) 340 mA

Input Voltage

(Scanner) 3.4V ~ 4.2V

Power -Operating

(Scanner) 3.2V ~ 4.0V

Power –Standby

(Scanner) 3.4V ~ 4.2V

Current –Operating

(Scanner) 225 mA

Current –Standby

(Scanner) 13 mA

Light Level Up to 70000 Lux

Shock 1.5m drop onto concrete

Contaminants Seals to resist airborne particulate

contaminants (IP42)

Ventilation None required

Programming

method

Manual (Reading special barcode)

DOS

command through RS-232, Windows

configuration program

Program upgrade Enabled by built-in flash memory

Programmable

characteristics

Code type selection, check digit

selection Decoding option Decoding

option Transmitted character delay,

Header selection, trailer selection,

message suffix, good read beep tone

and volume, scanner trigger selection

Keyboard emulation type

(intermessage delay, keyboard type

and keyboard language)

Serial interface type (ACK/NAK,

Xon/Xoff, RTS/CTS, good read LED

control, start/stop bits)

Programming the AS-8510 / 8512

To program the 8510 or 8512, you must scan a series of

programming barcode in the correct order. Fold out the back

cover of this manual. You will see a table of alphanumeric

barcodes, which are used to program the various options

presented.

To program each option, you must:

1. Scan the Program barcode on the parameter setting part.

2. Enter the option mode by scanning the Option Bar Code

(also on the Parameter setting part).

3. To the right of the option barcode, the necessary

alphanumeric inputs are listed. Scan these alphanumeric

entries from the back fold outpage. To confirm above

steps, you must scan the Finish barcode on the back fold

out page.

4. Once you have finished programming. Scan the Exit

barcode, listed on the lower right hand corner of each

parameter setting part.

Option Bar Code Option AlphanumericEntry

Interface

selection

Keyboard Wedge

RS-232

Wand emulation

USB

Keyboard/RS-232

Autodetection

Reserved

00*

Program

Exit

Program Barcode

Option Barcode

Exit Barcode

Back Fold Out

Finish barcode

Exit

Interface Selection

This decoder built-in scanner comes in one model and

supports interfaces such as keyboard wedge, RS232 serial

wedge, wand emulation, and the latest USB interface. In

most of the cases, simply selecting an appropriate cable with

a device code will work for a specific interface.

Interfaceselection:You can change factory interface

default for other type interface. By plugging different cables,

setting right interface, then the scanner will be changed to

another interface. However, you must make sure which cable

you need.

Keyboard/RS232/UBS Auto detection: By setting this

function, it will automatically select the Keyboard wedge or

RS-232 or UBS interface for user.

Option Bar Code Option Alphanumeric

Entry

Interface selection

Keyboard Wedge

RS-232

Wand emulation

USB

Keyboard

/RS232/USB

Auto detection

Reserved

(8110/8210/8150)

04*

Program

Note:*-Default

Exit

Keyboard wedge

As a keyboard interface, the scanner supports most of the

popular PCs and IBM terminals. The installation of the wedge

is a fairly simple process without any changes of software or

hardware.

Keyboard Type: Select keyboard type connector of your

host computer. Scanner must be selected to the appropriate

host interface cable converter.

Option Bar Code Option Alphanumeric

Entry

Keyboard type

IBM AT, PS/2

Reserved

00*

Program

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Argox Barcode-Lesegerät Handbücher

Argox

Argox OS Series Bedienungsanleitung

Argox

Argox AI-6800 Bedienungsanleitung

Argox

Argox PT Bedienungsanleitung

Argox

Argox AS-9300 Bedienungsanleitung

Argox

Argox OS-214 plus Bedienungsanleitung

Argox

Argox A-2240 Bedienungsanleitung

Argox

Argox AR-3201 Bedienungsanleitung

Argox

Argox AR-300 Bedienungsanleitung

Argox

Argox P4 Series Bedienungsanleitung

Argox

Argox AS-8000 Series Bedienungsanleitung

Argox

Argox AS-8020 Bedienungsanleitung

Argox

Argox AS-8312 Bedienungsanleitung

Argox

Argox Smart CP-2140 Bedienungsanleitung

Argox

Argox OS Series Bedienungsanleitung

Argox

Argox AS-8110 Bedienungsanleitung

Argox

Argox OS-214 plus Bedienungsanleitung

Argox

Argox Smart CP-2140 Bedienungsanleitung

Argox

Argox amigo series Bedienungsanleitung

Argox

Argox P4 Series Bedienungsanleitung

Argox

Argox D2 Series Bedienungsanleitung

Argox

Argox AME-3230B Bedienungsanleitung

Argox

Argox AP-9800 Bedienungsanleitung

Argox

Argox OS-214 plus Bedienungsanleitung

Argox

Argox Xellent X-1000VL Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung