ArgoxScan AS-8020CL Bedienungsanleitung
NOTICE:
This equipment has been tested and complied with
the limits for a Class a digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to
provide a reasonable protection against harmful
interface when the equipment is operated under a
commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the
instruction manual, may cause harmful interface to
radio communications. Operation of this equipment in
a residential area is likely to cause harmful interface in
which case the user will be required to correct the
interface at his own expenses.
Note: All brands and trademarks shall belong to their
respective owner.
Note: Specification is subject to changes without
notice.
This device complies with Part 15 of the FCC Rules.
Operation shall be subject to the following two
conditions:
(1) This device may not cause harmful interface, and
(2) This device must accept any interface received,
including interface that may cause undesirable
operation.
Using the ArgoxScan AS-8020CL
The ArgoxScan can automatically scan barcode at a distance.
Simply aim and pull the trigger. Code scanning is performed
along the center of the light bar emitted from the reading
window. This bar must cover the entire code (see “How to
Scan” in page 9).
Successful scanning shall be obtained by tilting the scanner
with respect to the barcode to avoid direct reflections that
impair the reading performance.
Recommended Steps
When the required settings have been configured, all settings
are stored in non- volatile memory of scanner and cradle
after reading EXIT Label. Recommended steps are as
follows.
1) Host interface will be automatically detected. User does
not need to set host interface for the cradle.
2) Set interface to optimize protocol of cradle with your
host in interface section.
3) Set system control of scanner, such as specific
adjustments double confirm, indicator and scanning
mode which you prefer usage in system control section.
4) Set code options of scanner for your usage in code
option section. You must make sure to enable the
symbology first, then Min./Max. code length, code ID
checksum and truncate digits are also converted.
5) Set string format of the scanner, such as preamble,
postamble Prefix, suffix, code ID and code name
transmission for your application in string format
section.
Note: If still not work properly. Please contact your dealer for
further information.
警告： 電池若未妥善處理， 可能會導致爆炸。
請勿拆卸電池， 或用火銷毀電池。 請將電池放置於兒童拿不
到的地方。 請使用專用充電器充電， 並請依照當地政府或法
律規定妥善處理廢棄電池。
CAUTION: EXPLOSION HAZARD
Do not disassemble, short circuit, heat the battery or dispose
of in fire. Store battery pack in a proper place. Do not expose
to temperature above 60℃/140℉. Use specified charger
only. Please dispose of the used batteries following the rules
or laws issued by the local government.
CONTENTS
Chapter 1 Introduction
Installation…………………………………………… 1
How To Scan………………………………………… 13
Troubleshooting……………………………………… 14
Wireless Connection………………………………… 16
Battery Charging…………………………………… 19
Wireless Features…………………………………… 22
Auto Update……………………………………… 23
Deep Sleep Mode……………………………… 25
Wireless Connectivity…………………………… 26
Inquiry Beep control…………………………… 28
Cradle Beep Loudness Control………………… 30
Additional Features……………………………… 32
Default Setting.……………………………………… 33
Specification………………………………………… 34
Indications of AS-8020CL…………………………… 37
Imager…………………………………………… 37
Cradle…………………………………………… 38
Programming the AS-8020CL……………………… 39
Chapter 2 Parameter Setting
Interface………………………………………………… 41
Interface Selection.………………………………… 41
Keyboard wedge.…………………………………… 42
RS-232.……………………………………………… 47
Pin Assignments.…………………………………… 51
System Control……………………………………… 53
Scan………………………………………………… 53
Indication. …………………………………………… 57
Code Option…………………………………………… 59
UPCA.………………………………………………… 59
UPCE ………………………………………………… 63
EAN-13.……………………………………………… 67
EAN-8 ………………………………………………… 71
Code 39 ……………………………………………… 75
Interleaved 2 of 5 …………………………………… 79
Industrial 2 of 5 ……………………………………… 81
Matrix 2 of 5 Eur …………………………………… 83
Codabar ……………………………………………… 85
Code-128 …………………………………………… 89
Code-93 ……………………………………………… 93
Code-11.……………………………………………… 95
MSI/Plessey.………………………………………… 97
UK/Plessey.………………………………………… 99
Telepen.……………………………………………… 101
Standard 2 of 5 ……………………………………… 103
China Post …………………………………………… 105
Italian pharmacode (Code 32)..…………………… 107
Code-16K…………………………………………… 109
PDF-417……………………………………………… 111
EAN UCC Composite……………………………… 113
RSS-14.……………………………………………… 115
RSS-Limited………………………………………… 117
RSS-Expanded……………………………………… 119
Micro-PDF…………………………………………… 121
String Format…………………………………………… 123
String Setting / Transmission (Prefix/Suffix)……… 123
String Setting / Transmission
(Preamble/Postamble)……………………………… 125
String Setting / Transmission
(Insert Group Characters)………………………… 127
String Setting / Transmission (Others)…………… 131
Appendix………………………………………………… 133
Test Chart.…………………………………………… 133
ASCII Code Table …………………………………… 136
Parameter Setting List.……………………………… 137
1
Installation
The AS-8020CL Wireless Imager is easy to install and use.
Please see the following figure showing the steps to perform
the installation.
* Note: Turn off the host computer before installation.
1. Connect the interface (I/F) cable to the cradle.
2. Connect the power cord to the cradle.
3. Route the I/F cable and power cord through the notch.
4. Connect the I/F cable to the host computer
communication port.
5. Connect the AC adapter to the wall outlet.
6. Place the imager in the cradle and verify the charge
LED is flashing. Charge the battery for at least 8 hours
before the first use.
7. To verify operation, please link the imager with cradle
first (Refer to “Wireless Connection” in page 12). Point
the imager at the barcode and pull the trigger. The
imager should emit a beep indicating that the barcode
has been scanned and transmitted to the cradle
successfully.
2
Connecting AS-8020CL to PC with USB Dongle
AS-8020CL is allowed to connect with PC via USB dongle.
1. .Scan the following barcodes to set scanner to Bluetooth
connection mode, with PIN code as 0000 or refer to the
manual page 23rd to set any four-to-six character PIN
code assigned to the target Bluetooth device
Cradle/Dongle connection auto detection – The imager
can be linked to either a cradle or other Bluetooth
enabled devices.
Set PIN code to 0000
2. After well-connecting Bluetooth dongle to PC, find the
blue-tooth sign on Taskbar; double-click on it to bring out
the Bluetooth Devices prompt.
After well-connecting USB dongle to PC, find the blue-tooth
sign on Taskbar; double-click on it to bring out the
Bluetooth Devices prompt. (Or go to Control Panel –
Bluetooth Device…)
3
Within the prompt, click “Add”.
3. Check the option, “My device is set up and ready to be
found” and click” Next”.
4
4. Select “AS-8020CL” among the Bluetooth devices found;
click “Next”.
5. Select “Don’t use a passkey” and click “Next”. The
Bluetooth connection will start to install the Bluetooth
device for AS-8020CL:
Inhaltsverzeichnis
Andere ArgoxScan Barcode-Lesegerät Handbücher
Beliebte Barcode-Lesegerät Handbücher anderer Marken
POSMicro
POSMicro Datalogic PowerScan D7100 Bedienungsanleitung
Marson
Marson MT780 Kurzanleitung zur Einrichtung
NCR
NCR RealPOS Bedienungsanleitung
Motorola
Motorola SE3300 Kurzanleitung zur Einrichtung
Element
Element P130BT Bedienungsanleitung
Motorola
Motorola Symbol LS3008 Installations- und Betriebshandbuch
