Ariston Genus 27 Plus Bedienungsanleitung

403

Users

Manual

403

TABLE OF CONTENTS

1) GENERAL INFORMATION page 3

2) OPERATING INSTRUCTIONS page 4

3) TIME CLOCK page 7

4) USEFUL INFORMATION AND TROUBLESHOOTING page 10

IMPORTANT

Please read this manual carefully.

For additional information, please consult the “Installation and Servicing Instructions.”

Please ensure manuals provided are kept with the appliance so that they can be used by the end-

user, installer or our authorised engineer.

Dear Customer,

Thank you for choosing an ARISTON boiler.

We guarantee that your boiler is a

reliable and technically sound product.

This User’s Manual provides detailed instructions and recommendations for proper installation,

use and maintenance.

Remember to keep this manual in a safe place for future reference i.e. by the gas meter.

Your local MTS Servicing Centre is at your complete disposal for all requirements.

MTS (GB) Limited

Every attempt has been made to avoid errors of

any kind

in this User’s Manual, the Management

invites customers to inform

of any inaccuracies which they may find.

This will help to improve our service

The guarantee on this appliance is valid

for 12 months from the first day of

installation.

Repairs to the electric, hydraulic or gas

circuits may be carried out only by your

local authorised MTS Servicing Centre.

403

CONTROL PANEL

Legend

A) Ignition Lockout Reset Button/Safety (Overheat)Thermostat Reset

B) Ignition Lockout L.E.D.

C) Selector Knob for Summer/Winter/Flue Analysis Modes

D) Low System Water Level L.E.D.

E) Temperature Adjustment Knob for Domestic Hot Water

F) Heating System Thermometer

G) Safety (Overheat)Thermostat Intervention L.E.D.

H) Adjustment Knob for Heating Temperature

I) On/Off L.E.D.

L) On/Off Switch

O) Heating System Pressure Gauge

MTS (GB) Limited support the initiative.Your installer will give

you, and show you how to use, a logbook which will give you important

information about your boiler, and heating system. Please have this

logbook to hand whenever you contact a service engineer or us.

All CORGI Registered Installers carry a CORGI ID card, and have

a registration number. Both should be recorded in your boiler

Logbook. You can check your installer is CORGI registered by

calling CORGI direct on :- (01256) 372300.

This is a combined appliance for the production of central heating

(C.H.) and domestic hot water (D.H.W.).This appliance must be used

only for the purpose for which it is designed. The manufacturer

declines all liability for damage caused by improper or negligent use.

Do not allow children or inexperienced persons to use the appliance

without supervision.

If you smell gas in the room, do not turn on light switches, use the

telephone or any other object which might cause sparks.

Open doors and windows immediately to ventilate the room.

Shut the gas mains tap (on the gas meter) or the valve of the gas

cylinder and call your Gas Supplier immediately.

If you are going away for a long period of time, remember to shut the

mains gas tap or the gas cylinder valve.

Before any intervention within the boiler it is first necessary to cut

off the electrical power supply by turning the external switch to

“OFF”.

This manual may be kept in the front panel of the boiler.

1. GENERAL

INFORMATION

FR004A

403

CAUTION

Installation, start-up, adjustments and maintenance must be

performed by a competent person only, in accordance with the

current Gas Safety (Installation & Use) Regulations and the

instructions provided. Improper installation may cause damage or

injury to individuals, animals and personal property, for which the

manufacturer will not be held liable.

To ensure efficient and safe operation it is recommended that the

boiler is serviced annually by a competent person.

If it is known or suspected that a fault exists on the appliance, it

must not be used until the fault has been corrected by a competent

person.

HELPFUL SUGGESTIONS

To get the most out of your boiler, we have provided you with some

useful advice on the proper use and maintenance:

- Periodically check the system pressure using the pressure guage

“O”, make sure that the pressure at 1.5 bar (the blue part on the

gauge) when the system is off and cool. The warning L.E.D. “D” will

indicate if the pressure is below the minimum recommended value.

Consult your installer for checking and refilling the system.

- The outer panels of the unit's case must only be cleaned with a damp

cloth. Do not use abrasive cleaners.The Control panel can be wiped

with either a damp or dry cloth. Spray polishes must not be used on

the control panel surface or knobs. Care must be taken in preventing

any liquid entering the appliance.

- If the water is exceptionally hard, install a water softener so that the

efficiency of the unit remains the same over time, as this will consume

less gas.

- To improve comfort and take full advantage of the heat produced by

the boiler, it is recommended that an external thermostat be installed.

- If the boiler is not going to be used for an extended period of time, turn

off the supply of electricity to the unit by pressing the On/Off switch

“L”.

- The green L.E.D.“I”will turn off.Then turn off the supply of gas to the

unit itself.

- It is good practice to clean and service the appliance and central

heating system every year.

- Call an Authorised Service Centre.

2. OPERATING

INSTRUCTIONS

START-UP PROCEDURE LIGHTING

Before starting the unit, check the following:

· The water pressure on the pressure gauge “O”;

· That the gas cock and the inlet for domestic water are

open.

These models are equipped with electronic ignition which utilises

contact ionisation.

To make the boiler operational, simply press the On/Off switch “L”.

The green L.E.D. “I” will then turn on.

At this point the boiler is ready for use: a centralised electronic control

unit will automatically light the main burner when needed. If the burner

UT001A

UT008Aa

403

°C

40 50 607080

does not light within the pre-set safety time limit, the red “B” L.E.D.will

light up. To reset the ignition system, the reset button “A” must be

pressed. Should the system fail to light a second time, check to make

sure that the gas cock is open. If the problem persists, contact one of

our Authorised Service Centres for assistance.

WINTER AND SUMMER OPERATING MODES

The boiler is fitted with a selector knob “C” which allows you to switch

between winter <>and summer <>and also heating only <

> operating modes and vice versa.When the knob is set to <

>, the boiler can serve the dual purpose of providing heat and/or hot

water for domestic use.

The supply of hot water for domestic use always takes precedence

over heating. When the knob is set to <>,the boiler cuts out the

heating system and only provides hot water for domestic use (when

needed).

TURNING ON THE CENTRAL HEATING

Installation without a room thermostat :

- Turn on the power supply to the boiler by pressing the

On/Off switch “L”; the green L.E.D. “I” will then turn on;

- Turn the “C” selector knob to <>or < > (in this position no

domestic hot water is produced);

- Regulate the temperature of the water in the boiler by turning the “H”

knob. The temperature can vary between 42°C and about 82°C;

- Check the boiler temperature on the thermometer with the yellow

L.E.D.s “F”. With this type of installation, the ambient temperature

does not influence the operation of the boiler and the circulation

pump always remains in operation.

UT008Ab

UT008Ac

UT008Ad UT008Ae

UT008Aa

403

Installation with a room thermostat:

- Turn the “C” selector knob to < >;

- Turn on the power supply to the boiler by pressing the On/Off switch

”L”; the green L.E.D. will then turn on;

- Turn the thermostat knob “H” to the highest temperature setting.

- With this type of installation, the boiler is controlled by a room

thermostat

. Therefore, it runs until the ambient temperature has reached the

temperature setting on the thermostat. At that point, the main burner

will turn off and the circulation pump will stop.

TURNING OFF THE CENTRAL HEATING

Installation without a room thermostat:

To turn off the heating, turn the “C” selector knob to < >.The boiler

will still provide hot water for domestic use.

ADJUSTING THE HEATING TEMPERATURE

To economise on consumption while achieving the highest level of

comfort, the temperature adjustment knob is designed with three

different heating zones based on the temperature outside the home.

Rotate the knob “H” as shown below.

PRODUCTION OF HOT WATER

FOR DOMESTIC USE

- Turn on the power to the boiler by pressing the On/Off switch “L”;

- Turn the “C” selector knob to <>or < > (in this position no

central heating is produced);

- Turn the “E” knob to select the temperature for the hot water

(between 40°C and about 70°C).

ADJUSTING THE TEMPERATURE OF

WATER FOR DOMESTIC USE

It is recommended that the temperature for the hot water should not be

set to high temperatures and then mixed with cold water. Setting the

thermostat to medium temperatures is preferable

(see figure)

•

From +5°C

to +15°C

Lower

than -5°C

From +5°C

to -5°C

UT008Af

UT008Ag

•

UT008Ai

•

UT008Al

UT008Ah

403

Operating the time switch

The step marked with the symbol “”are necessary to carry out a

switching program.

Preparing for Operation

Activate the “Res”switch (=RESET) to reset the time switch to its

default setting (activate using a pencil or similar pointed instrument).Do

this:

- every time you wish to “reset”the time switch

- to erase all switching times and the current time of day.

After approximately two seconds the following display appears:

Enter current time and weekday

- Keep the “”key pressed down

During the summer time period press the +/- 1h key once.

Enter the hour using the “h”key

Enter the minutes using the “m”key

Enter the day using the “Day”key

1 = “Monday”..............7 = Sunday

- Release the “”key.

Day

Manual switch

Summer and

winter time

setting

Reset

Enter

weekday/s

Enter

the hours

Week-

days

flash

Enter

minutes

Enter

switching

times

Imput

time

3.TIME CLOCK

SHUTDOWN PROCEDURE

To turn off the main burner, simply press the On/Off switch “L”; the

green L.E.D. “I”will also turn off.

As a precautionary measure, it is recommended that the gas cock

located on the bottom of the boiler be turned off as well.

UT008Aa

UT008Am

Input

403

Automatic Manual Continuous

Operation Operation Operation

The switching If the current You can only

times corres- switching mode is return to automatic

pond to the changed manually, mode from the

program the next switching continuously-ON

entered. time will be and continuously-

carried out auto- OFF switching

matically again modes by

according to the pressing the " "

entered switching key.

program.

= ON = ON = Continuously ON

= OFF = OFF = Continuously OFF

Entering the switching times

You have 20 memory Iocations available.Each switching time takes up

one memory location.

Keep pressing the “Prog”key until a free memory location is shown in

the display “– –:––”.

Programme ON or OFF with the “”key:

“”= OFF; “”= ON

Enter the hour using “h”

Enter the minutes using “m”

If a switching command is to be carried out every day (1 2 3 4 5 6 7)

then store using the “”key, otherwise select the day(s) it is to be

carried out by using the “Day”key.

When the day seIection is left bIank, the programmed switching

instruction operates at the same time every day

1 2 3 4 5 6 = Monday –Saturday

1 2 3 4 5 = Monday –Friday

6 7 =Saturday –Sunday

Selection of single days: 1 = Mon. .............. 2 =Tues.

Save the switching time with the “”key.

The time switch enters the automatic operating mode and displays the

current time of day.

Begin any further entry of a switching time with the “Prog”switch. If

your entry is incomplete, the segments not yet selected will blink in the

display. After programming is completed, and you return the time clock

to the current time display with the “”key, the time clock will not

activate any switching instruction required for the current time.You may

need to manually select the desired switching state with the “”

key.Thereafter, as the unit encounters further switching instructions in

the memory in real time, it will correctly activate all subsequent

switching instructions.

Manual Override Switch “”

With the “”you can change the current setting at any time. The

switching program already entered is not altered.

UT008An

Reading the programmed switching times

Pressing the “Prog”key displays the programmed switching times until the

first free memory location appears in the display “– –: ––”.

If you now press the “Prog”key once again, the number of free memory

Iocations will be displayed, e.g. “FR 1188 ”. If all memory locations are

occupied, the display “FR 0000 ”appears.

Changing the programmed switching times

Press the “Prog”key repeatedly until the switching time you want to change

is displayed. You can now enter the new data. See point “Entering the

switching times”.

Notes on storing switching times:

If you end your entry of the switching times by pressing the “Prog”key, then

the switching time you have entered will be stored and the next memory

location displayed. Entry of further switching times is also carried out as

described in point 4.3.

In addition, a complete switching command is stored automatically after

around 90 seconds provided no other key is pressed.The time switch then

enters the automatic operating mode and displays the current time again.

Deleting individual switching times

Press the “Prog”key repeatedly until the switching time you wish to delete

is shown in the display. Then set to “– –” using the “h”or “m”key and keep

the “”key pressed down for around 3 seconds.The switching time is now

erased and the current time is displayed.

AM / PM time display

If you press the “+/-1h”and “h”keys at the same time, the time display

switches into the AM/PM mode (mostly used in English-speaking countries).

Technical data

Connection see unit imprint

Switching capacity see unit imprint

Ambient temperature -10°C to +55°C

Running reserve 5 h at + 20°C

Memory Iocations 20

Shortest switching time 1 min.

Programmable every minute

403

4. USEFUL INFORMATION

AND TROUBLESHOOTING

BOILER SHUTDOWN

The boiler unit is equipped with safety devices which intervene in

certain situations to shutdown the boiler.

Some of these situations are signalled by the unit and can be corrected

by the user.

SHUTDOWN DUE TO THE FAILURE OF THE

BURNERTO LIGHT AUTOMATICALLY

This anomaly is indicated by the red “B”L.E.D.

To reset the unit, press and then release the “A”button.

At this point, the electronic ignition system will attempt to light the

burner again.

If lighting failure occurs repeatedly, it is recommended that you contact

one of our Authorised Service Centres.

SHUTDOWN DUE TO OVERHEATING

This anomaly is signalled by the red “G”L.E.D.

The boiler shuts off because the safety thermostat detected that the

boiler temperature has reached the temperature limit.

To reset the unit, wait until the boiler has cooled and then press the “A”

button.

If the safety thermostat shuts off the unit on a frequent basis, contact

one of our Authorised Service Centres for assistance.

SHUTDOWN DUE TO INSUFFICIENT

WATER CIRCULATION

This anomaly is indicated by the red “D”L.E.D.

One of the possible causes of this shutdown situation could be the lack

of water in the boiler or water circulation failure in the primary heating

circuit.

Check the system pressure on the pressure gauge “O”and, if it is less

than 0.5 bar, consult your installer for checking and refilling the system.

Then reset the unit by turning the boiler off and then back on with the

On/Off button “L”.

If this situation persists, contact one of our Authorised Service Centres.

UT008Aa

UT001A

UT008Ap

UT008Ab

UT008Ao

Andere Handbücher für Genus 27 Plus

Inhaltsverzeichnis

Andere Ariston Kessel Handbücher

Ariston

Ariston GENUS 30 Plus Benutzerhandbuch

Ariston

Ariston CLAS NET One Bedienungsanleitung

Ariston

Ariston EGIS PLUS 24 FF Bedienungsanleitung

Ariston

Ariston ecoCOMBI 27 MFFI Benutzerhandbuch

Ariston

Ariston ecoGENUS 24 MFFI Bedienungsanleitung

Ariston

Ariston benchmark GENUS HE SYSTEM Bedienungsanleitung

Ariston

Ariston GENUS Bedienungsanleitung

Ariston

Ariston microGENUS 23 MFFI Bedienungsanleitung

Ariston

Ariston EGIS PREMIUM S 25 Benutzerhandbuch

Ariston

Ariston MICROCOMBI 23 MFFI Bedienungsanleitung

Ariston

Ariston microGENUS II 31 MFFI Benutzerhandbuch

Ariston

Ariston GENUS 24 FF Bedienungsanleitung

Ariston

Ariston GENUS PREMIUM EVO HP 45 Bedienungsanleitung

Ariston

Ariston ecoGENUS 24 MFFI Benutzerhandbuch

Ariston

Ariston GENUS HE 30 FF SYSYEM NG Leitfaden

Ariston

Ariston ACO 32 RFFI Benutzerhandbuch

Ariston

Ariston GENUS HE 35 Plus Benutzerhandbuch

Ariston

Ariston microSYSTEM 10 RFFI Benutzerhandbuch

Ariston

Ariston Clas 24 FF Bedienungsanleitung

Ariston

Ariston GENUS 32 Benutzerhandbuch

Ariston

Ariston INTESA TP23 Bedienungsanleitung

Ariston

Ariston microGENUS II 24 MFFI Bedienungsanleitung

Ariston

Ariston 47-116-65 Bedienungsanleitung

Ariston

Ariston MICROCOMBI 23 MFFI Bedienungsanleitung

Beliebte Kessel Handbücher anderer Marken

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Bedienungsanleitung

Radijator

Radijator BIO max 23.1 Bedienungsanleitung

Brunner

Brunner BSV 20 Bedienungsanleitung

Buderus

Buderus Logamax GB062-24 KDE H V2 Bedienungsanleitung

Potterton

Potterton 50e Datenblatt

UTICA BOILERS

UTICA BOILERS TriFire Bedienungsanleitung

Joannes

Joannes LADY Series Handbuch

ECR International

ECR International UB90-125 Gebrauchsanweisung

Froling

Froling FHG Turbo 3000 Bedienungsanleitung

Froling

Froling P4 Pellet 8 - 105 Bedienungsanleitung

U.S. Boiler Company

U.S. Boiler Company K2 Bedienungsanleitung

Henrad

Henrad C95 FF Bedienungsanleitung

NeOvo

NeOvo EcoNox EF 36 Bedienungsanleitung

Potterton

Potterton PROMAX SL 12 Bedienungsanleitung

Eco Hometec

Eco Hometec EC 25 COMPACT Bedienungsanleitung

Viessmann

Viessmann VITODENS 200 Leitfaden

Baxi

Baxi Prime 1.24 Bedienungsanleitung

REXNOVA

REXNOVA ISA 20 BITHERMAL Bedienungsanleitung