Armstrong S-55 Bedienungsanleitung

File No: 10.801

Date: october 26, 2015

Supersedes: 10.801

Date: october 15, 2013

GOLD SERIES - PUMP LESS VOLUTE KITS

FOR SELECT 2, 3, 4, AND 5, AND 1050 SERIES IN-LINE CIRCULATOR

MODELS

INSTALLATION AND OPERATING INSTRUCTIONS

1.0 Application 1

2.0 Installation 1

3.0 Starting up 1

4.0 Lubrication 2

5.0 Seal replacement 2

caution

Always disconnect power supply from motor before

servicing.

1.0 application

Armstrong Gold series – Pump Less Volute kits may be used to

replace,upgrade, and renew all working parts of any compatible

3piece circulator. The kits are suitable for both hydronic ﬂuid

and potable water applications. Refer to Armstrong cross refer-

ence information to determine compatibility.

2.0 installation

In-line circulators should always be installed with the shaft in

a horizontal position. The circulator should be mounted by the

volute pipe connections only. No other support for the circula-

tor should be used.

Circulator replacement should only be performed by qualiﬁed

personnel. To avoid personal injury or property damage, before

attempting circulator replacement:

1Hydraulically isolate the circulator from the system in which

it isinstalled.

2Disconnect / lockout power at the electrical panel.

3 Carefully alleviate pressure and drain the ﬂuid from the

circulator.

4Avoid spillage of, or physical contact with, the system ﬂuid.

To remove the original circulator:

1 Disconnect the power wiring at the terminal box.

2 Remove the screws that connect the sealed bearing

assembly tothe volute (casing).

3Pull the circulator straight out, avoiding impeller contact

with the inside of the volute.

4 Remove any remaining gasket from the mating surface of

the volute.

5Be careful not to damage gasket mating surfaces.

To install the new Gold Series – Pump Less Volute kit:

1Apply the new gasket (supplied) to the volute

mating surface.

2Position the kit with the oil ﬁlling cup located on top of the

sealed bearing assembly.

3 Mate the kit up with the original volute, ensuring the

gaskets seats squarely.

4 Ensure the impeller does not contact the inside volute

surfaces.

5 While holding the kit steady, start two screws, diagonally

opposed, to secure the mating parts.

6 Insert the remaining screws ﬁnger-tight, noting the gap

between the bearing body and volute.

7 Progressively tighten the mating screws in a diagonal

pattern. Avoid over-tightening.

8 Rotate the pump shaft at the coupler to ensure it turns freely

and impeller doesn’t bind.

9 Verify nameplate voltage before connecting power wiring.

3.0 starting up

The pump must be fully primed on start-up. Fill system piping

and pump body with liquid and vent complete system, turning

pump by hand to dislodge air from body. Make sure ﬁttings and

drain valves are airtight, then add any additional ﬁll required.

installation &

operating instructions

Gold series - Pump

Less Volute kits

Check motor electrics against available supply, then start pump

making sure rotation is correct. When viewed from motor end,

rotation is counter-clockwise on Models s-25 to s-46 and

h-32 to h-41. On all other models, rotation is clockwise. If

pressure does not develop, stop pump, re-check, vent and ﬁll.

Never attempt to ﬁll system when pump is running.

4.0 lubrication

caution

Do not put oil in the maintenance free PLVs. These

models contain mf in their item numbers and are

labelled: 'This bearing assembly contains perma-

nently lubricated bearings and does not need any

oiling or greasing'.

pump lubrication

Immediately after pump is installed and before running, slowly

add the oil (sae 30 non-detergent regular, supplied with

pump) to pump oil cup, located on top of bearing bracket:

s-25 to s-57, h-32 to h-54 and series 1050 (1b to 2b)¼oz.

At the start of each following heating season, lubricate with

sae 30 oil. For models s-25 to s-57,h-32 to h-54 and series

1050 (1b to 2b), add approximately ¼ oz. (Lubricate every six

months for high temperature or constant operation.)

motor lubrication

Gold series – Pump Less Volute motors are permanently

lubricated and require no maintenance.

5.0 seal replacement

Remove pump bracket from body. Remove the impeller, dam-

aged seal assembly, ceramic insert and rubber cup. Clean the

recess in bearing bracket coverplate and install a new retainer

cup and ceramic. Check the condition of the shaft sleeve. If

scored, replace the shaft assembly. Otherwise, clean shaft ex-

tension and polish sleeve with ﬁne crocus cloth, using a rotating

motion, if required.

Press against coupler end of shaft to take up play while press-

ing new seal ﬁrmly against the stationary face. A slight amount

of clean vaseline may be put on shaft sleeve to assist installa-

tion. Press down ﬁrmly and evenly, using 2screwdrivers and

pushing against the 4ears of driving band (the metal ring

around rubber bellows), or around top outer edge of driving

band on models s-25 to s-57, h-32 to h-54 and series 1050

(1b to 2b).

Do not use spring washer on models s-25, s-35 and h-32

current style circulators, where recess to locate spring is pro-

vided on impeller hub.

Continue pressing against coupler end of shaft, re-mount

impeller and re-assemble the seal bearing assembly into body.

If necessary, install a new body gasket and clean gasket surface

of both volute and bracket.

caution

Before operating pump, carefully check:

1Is the pump primed?

2Is rotation correct?

3Is pump properly lubricated?

4Does the power supply agree with data on

motor nameplate?

5Is overload protection provided?

6Is the system clean?

birmingham

buffalo

toronto

manchester

bangalore

shanghai armstrongfluidtechnology.com

+91 (0) 80 4906 3555

+44 (0) 8444 145 145

+1 716 693 8813

+1 416 755 2291

+86 21 3756 6696

armstrong fluid technology

established 1934

Andere Handbücher für s-55

Dieses Handbuch passt für folgende Modelle

Andere Armstrong Wasserpumpe Handbücher

Armstrong

Armstrong Design Envelope 4300 Bedienungsanleitung

Armstrong

Armstrong Astro 2 Bedienungsanleitung

Armstrong

Armstrong Design Envelope 4380 Bedienungsanleitung

Armstrong

Armstrong LIFT NT25 Bedienungsanleitung

Armstrong

Armstrong 4039 Series Bedienungsanleitung

Armstrong

Armstrong ASTRO 220SSU Bedienungsanleitung

Armstrong

Armstrong Design Envelope 4300 Bedienungsanleitung

Armstrong

Armstrong Design Envelope 4300 Bedienungsanleitung

Armstrong

Armstrong HEP OPTIMO Bedienungsanleitung

Armstrong

Armstrong Design Envelope 4312 Bedienungsanleitung

Armstrong

Armstrong Design Envelope 4300 Bedienungsanleitung

Armstrong

Armstrong Design Envelope 4300 Bedienungsanleitung

Armstrong

Armstrong Design Envelope 4302 Bedienungsanleitung

Armstrong

Armstrong VMS Series Bedienungsanleitung

Armstrong

Armstrong Design Envelope 4380 Bedienungsanleitung

Armstrong

Armstrong HEP Optimo S Bedienungsanleitung

Armstrong

Armstrong 4280 Series Bedienungsanleitung

Armstrong

Armstrong Design Envelope 4302 Handbuch

Armstrong

Armstrong 4200H Bedienungsanleitung

Armstrong

Armstrong Design Envelope 4322 Bedienungsanleitung

Armstrong

Armstrong s-55 Benutzerhandbuch

Armstrong

Armstrong Double Duty 6 Bedienungsanleitung

Armstrong

Armstrong Design Envelope 4392 Bedienungsanleitung

Armstrong

Armstrong Design Envelope 4300 Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung

Armstrong s-55 Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken