ARRI Orbiter Anleitung zur Verwendung
ARRI - ORBITER
Short Manual
WARNING-
FULLY READ AND
UNDERSTAND
THESE
INSTRUCTIONS
BEFORE
OPERATING THE
ARRI ORBITER.
IMPROPER
HANDLING CAN
RESULT IN
SERIOUS HARM
OR DAMAGE. IF
YOU HAVE ANY
QUESTION
PLEASE CALL
416.869.3330.
ARRI - ORBITER
Short Manual
ARRI ORBITER FULL MANUAL: WWW.ARRI.COM
WARNING:
Lamphead and systems may only be operated and used by qualified persons.
Safety Concerning
Fire/Burns/Radiation (UV, VIS, IR):
Always Observe the minimum distances stated
on the type plate to allow light and heat radiation
to disperse safely. This will prevent danger to
persons and objects.
Lampheads must be placed at sufficient distance
from flammable materials or objects. The
minimum distance to lit objects written on the
lamphead describes a max. temp. of 90 Degrees
Celsius in spot-focus on the lit object.
DO NOT COVER ANY
VENTILATION SLOTS ON THE
LAMPHEAD!!!
______________________
Do not move lamphead past tilt angle
stated on the type plate as this might
cause the lamphead to overheat.
Do not operate the lamphead with
closed barndoors or an excessive
number of scrims, as this might also
cause overheating
Do no open the housing of the
Orbiter. For safe operation, the housing
must be completely closed at all times.
Take appropriate precautions when
lighting glass, windows and
decorative surfaces. These materials
can burst when they become hot.
A faultless function of the power supply
and protection system must be ensured
before connecting lamphead.
TYPE PLATE
ARRI - ORBITER
Short Manual
1 –Sensor for Display
Illumination
2 –Encoder
3 –Display
4 –Menu Buttons
5 –Quick Buttons
6 –Thread for D-Ring
7 –4 Pin Lemo Connector
8 –Connectors to Luminaire
9 –Neodymium Magnet
1 –Yoke
2 –Spigot (28mm Junior Pin)
3 –Upper Handle
4 –Protective Cap
5 –Rubber Feet
6 –Locking Slider
7 –Quick Release Lever
8 –Yoke Bracket
9 –Antenna (Wireless DMX)
10 –Comm. Interface (Lemo 5-pin)
11 –Optic Interface
12 –Light Aperture with Glass Cover
13 –Guide for Locking Pin
14 –Safety Loop Attachment
15 –Ambient Light Sensor
16 –Connector for Control Panel Ext. Cable
17 –Control Panel
18 –Focus Handle
19 –Mains in and out
20 –Battery Input 48V –52V ---
21 –Tilt Lock
22 –SD Card Slot
23 –USB Ports
24 –DMX in
25 –DMX out
26 –Ethernet Connector (RJ45)
27 –Ethernet Connector (RJ45)
28 –Status LED
29 –SYNC Connector (SMA)
30 –Reset Button
ARRI - ORBITER
Short Manual
ARRI ORBITER FULL MANUAL: WWW.ARRI.COM
1 –Top Latch
2 –Safety Loop Attachment
3 –Accessory Holder
4 –Second Barndoor Catch
5 –Reflector
6 –Quickmount Guides
7 –Digital Optics Interface (5-pin)
8 –Locking Pin
9 –Locking Slider (OPTIC RELEASE)
10 –Guide for Locking Pin
***ALWAYS: Secure Open Face Optic with Safety
Chain to Main Unit in Case Primary Catch Fails***
!- Digital Optic Interface WillAutomatically Recognize Type of Lens WhenAttached - !
Mounting Instructions:
1 –Align yoke adapters from bellow
2 –Lift upwards –latches engage
automatically (RED MARKINGS
SHOULD NOT BE VISIBLE)
Removal Instructions →
1 –Flip out one release lever and press
stirrup slightly downward until yoke
adapter slides out of yoke bracket
2 –Repeat for other side
!!! YOKE MUST BE MOUNTED
HANGING OR STANDING
VERTICALLY. LATERAL LOAD CAN
BREAK THE SPIGOT !!!
Lamphead must not be exposed to
vibrations
ARRI - ORBITER
Short Manual
MOUNTING LAMPHEAD:
*Always use a safety chain when mounting
above persons
**Always secure safety chain between
Optic attachment and Lamphead
***Orbiter MUST be mounted on its’ yoke in
perpendicular standing position, or hanging
position. NEVER APPLY A LATERAL LOAD
ON THE STIRRUP!!!
Lamphead must not be exposed to vibrations
MOUNTING OPTICS:
*Lamphead will not function without an
Optic attached**
1 –Turn off Orbiter
2 –Release Optic by pressing locking slider
inwards and turn counter clockwise
3 –Mount new Optic by lining up Bayonet
Catch, turn clockwise until lockingtab
engages. Check that it is secure.
ALWAYS REPLACE PROTECTIVE CAP
WHEN NOT IN USE!!!
ORBITER CONTROL
By applying power to the mains power, the Orbiter will start lightingafter a short start-up time with
the previous settings programmed.
Orbiter can either be controlled by: DMX (Input/Throughput), Ethernet (Daisy Chain), or the
Removable Control Panel
MODES: WHITE LIGHT –Optimized Colour Rendition or High Output (Green/Magenta)
COLOURED LIGHT –Colour Tone and Saturation can be adjusted continuously
**At very low light setting, colour will revert to white**
Full Spectrum Operating Modes: WWW.ARRI.COM
ORBITER CONTROL PANEL
The Control Panel can be used directly at the Orbiter, or via a connecting cable remote from the
Orbiter. **If two Controllers are connected, the cable-connected Controller has priority**
Connecting Directly to the Orbiter: place Control Panel diagonally to the left into the recess.
Then push in the right side into the recess, then push unit to the right until it locks in place.
Control Panel will connect automatically and start up when power is on.
Control Panel uses: LiOS (Lighting Operating System)
Control Panel User Manual: WWW.ARRI.COM
IF YOU HAVE ANY QUESTIONS OR
CONCERNS, PLEASE CONTACT
AFFILIATED EQUIPMENT
416.869.3330
Andere Handbücher für Orbiter
8
Andere ARRI Beleuchtungsausrüstung Handbücher
ARRI
ARRI L1.31230TA Bedienungsanleitung
ARRI
ARRI X 2 Bedienungsanleitung
ARRI
ARRI ARRISUN 12 Plus Bedienungsanleitung
ARRI
ARRI ARRIMAX 18/12 Bedienungsanleitung
ARRI
ARRI EB MAX 1.8 Bedienungsanleitung
ARRI
ARRI MaxMover DayLight Bedienungsanleitung
ARRI
ARRI M Series Bedienungsanleitung
ARRI
ARRI ARRILITE 750 Plus Bedienungsanleitung
ARRI
ARRI L Series Bedienungsanleitung
ARRI
ARRI Caster Series Bedienungsanleitung
ARRI
ARRI EB MAX 2,5/4 Bedienungsanleitung
ARRI
ARRI Skypanel PSU S360 Bedienungsanleitung
ARRI
ARRI EB MAX 12/18 Bedienungsanleitung
ARRI
ARRI EB MAX 1.8 Bedienungsanleitung
ARRI
ARRI TRUE BLUE ST 5 Theater Bedienungsanleitung
ARRI
ARRI SkyPanel Handbuch
ARRI
ARRI L1.0009652 Bedienungsanleitung
ARRI
ARRI COMPACT 6000 Plus Handbuch
ARRI
ARRI SkyPanel Bedienungsanleitung
ARRI
ARRI CLAYPAKY TAMBORA LINEAR 60 Bedienungsanleitung
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
