Arris SURFboard SB8200 Bedienungsanleitung

SURFboard® SB8200

DOCSIS® 3.1 Cable Modem

August 2016

User Guide

ARRIS Copyrights and Trademarks

No part of this publication may be reproduced in any form or by any means or used to make

any derivative work (such as translation, transformation, or adaptation) without written

permission from ARRIS Enterprises, LLC. (“ARRIS”). ARRIS reserves the right to revise this

publication and to make changes in content from time to time without obligation on the part

of ARRIS to provide notification of such revision or change.

ARRIS, SURFboard, and the ARRIS logo are all trademarks of ARRIS Enterprises, LLC. Other

trademarks and trade names may be used in this document to refer to either the entities

claiming the marks or the names of their products. ARRIS disclaims proprietary interest in

the marks and names of others.

ARRIS provides this guide without warranty of any kind, implied or expressed, including, but

not limited to, the implied warranties of merchantability and fitness for a particular purpose.

ARRIS may make improvements or changes in the product(s) described in this manual at any

time.

The capabilities, system requirements and/or compatibility with third-party products

described herein are subject to change without notice.

PN 365-095-30000 x.2SURFboard SB8200 Cable Modem User Guide

Table of Contents

1. Safety and Regulatory Information.......................................................................... 5

Important Safety Instructions............................................................................................ 5

FCC Statements.................................................................................................................. 7

Caring for the Environment by Recycling .......................................................................... 9

2. Getting Started ..................................................................................................... 10

Introduction..................................................................................................................... 10

In the Box......................................................................................................................... 10

Additional Item(s) Needed (Not Included) ...................................................................... 11

System Requirements...................................................................................................... 11

Contact Information ........................................................................................................ 11

3. Product Overview ................................................................................................. 12

Front Panel ...................................................................................................................... 12

Rear Panel........................................................................................................................ 13

Cable Modem Label......................................................................................................... 14

4. Installing the Cable Modem................................................................................... 15

Connect the SB8200 to Your Computer .......................................................................... 15

Establish an Internet Connection .................................................................................... 16

5. Using the Cable Modem Web Manager ................................................................. 17

Start the SB8200 Web Manager...................................................................................... 17

SB8200 Web Manager Screen Options................................................................... 18

Get Help........................................................................................................................... 19

Exit the SB8200 Web Manager........................................................................................ 19

6. Monitoring Your Cable Modem and Connected Network ....................................... 20

View the Cable Modem Product Information ................................................................. 20

View the Cable Modem Network Connection Status...................................................... 20

View the Cable Modem Event Log................................................................................... 22

Reset the Cable Modem Configuration Settings ............................................................. 23

Reboot the Cable Modem ............................................................................................... 23

Exit the SB8200 Web Manager........................................................................................ 23

7. Troubleshooting Tips............................................................................................. 24

Solutions .......................................................................................................................... 24

Front Panel LED Icons and Error Conditions.................................................................... 25

PN 365-095-30000 x.2SURFboard SB8200 Cable Modem User Guide

8. Warranty Information ........................................................................................... 26

PN 365-095-30000 x.2SURFboard SB8200 Cable Modem User Guide

Chapter 1

Safety and Regulatory Information

Important Safety Instructions

Read This Before You Begin —When using your equipment, basic safety precautions should

always be followed to reduce the risk of fire, electric shock, and injury to persons, including

the following:

Read all of the instructions listed here and/or in the user manual before you operate this

device. Give particular attention to all safety precautions. Retain the instructions for

future reference.

This device must be installed and used in strict accordance with manufacturer’s

instructions, as described in the user documentation that is included with the device.

Comply with all warning and caution statements in the instructions. Observe all warning

and caution symbols that are affixed to this device.

To prevent fire or shock hazard, do not expose this device to rain or moisture. The device

must not be exposed to dripping or splashing. Do not place objects filled with liquids, such

as vases, on the device.

This device was qualified under test conditions that included the use of the supplied

cables between system components. To ensure regulatory and safety compliance, use

only the provided power and interface cables and install them properly.

Different types of cord sets may be used for connections to the main POWER supply

circuit. Use only a main line cord that complies with all applicable device safety

requirements of the country of use.

Installation of this device must be in accordance with national wiring codes and conform

to local regulations.

Operate this device only from the type of power source indicated on the device’s marking

label. If you are not sure of the type of power supplied to your home, consult your dealer

or local power company.

Do not overload outlets or extension cords, as this can result in a risk of fire or electric

shock. Overloaded electrical outlets, extension cords, frayed power cords, damaged or

cracked wire insulation, and broken plugs are dangerous. They may result in a shock or fire

hazard.

Route power supply cords so that they are not likely to be walked on or pinched by items

placed upon or against them. Pay particular attention to cords where they are attached to

plugs and convenience receptacles, and examine the point where they exit from the

device.

Chapter 1: Safety and Regulatory Information

PN 365-095-30000 x.2SURFboard SB8200 Cable Modem User Guide

Place this device in a location that is close enough to an electrical outlet to accommodate

the length of the power cord.

Place the device to allow for easy access when disconnecting the power cord of the device

from the electrical wall outlet.

Do not connect the plug into an extension cord, receptacle, or other outlet unless the plug

can be fully inserted with no part of the blades exposed.

Place this device on a stable surface.

Avoid damaging the device with static by touching the coaxial cable when it is attached to

the earth-grounded coaxial cable-TV wall outlet.

Always first touch the coaxial cable connector on the device when disconnecting or

reconnecting the Ethernet cable from the device or user’s PC.

It is recommended that the customer install an electrical surge protector in the electrical

outlet to which this device is connected. This is to avoid damaging the device by local

lightning strikes and other electrical surges.

Postpone installation until there is no risk of thunderstorm or lightning activity in the area.

Do not use this product near water: for example, near a bathtub, washbowl, kitchen sink

or laundry tub, in a wet basement, or near a swimming pool.

Do not cover the device or block the airflow to the device with any other objects. Keep the

device away from excessive heat and humidity and keep the device free from vibration

and dust.

Wipe the device with a clean, dry cloth. Never use cleaning fluid or similar chemicals. Do

not spray cleaners directly on the device or use forced air to remove dust.

For added protection, unplug the device from the wall outlet and disconnect the cables to

avoid damage to this device during lightning activity or power surges.

Upon completion of any service or repairs to this device, ask the service technician to

perform safety checks to determine that the device is in safe operating condition.

Do not open the device. Do not perform any servicing other than that contained in the

installation and troubleshooting instructions. Refer all servicing to qualified service

personnel.

This device should not be used in an environment that exceeds 104° F (40° C)

SAVE THE ABOVE INSTRUCTIONS

Note to CATV System Installer —This reminder is provided to call the CATV system installer’s

attention to Article 820.93 and 820.100 of the National Electric Code, which provides

guidelines for proper grounding and, in particular, specifies that the Coaxial cable shield shall

be connected to the grounding system of the building, as close to the point of cable entry as

practical.

Chapter 1: Safety and Regulatory Information

PN 365-095-30000 x.2SURFboard SB8200 Cable Modem User Guide

FCC Statements

FCC Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the device off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

Increase the separation between the device and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) This device must

accept any interference received, including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by ARRIS for compliance

could void the user’s authority to operate the equipment

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. To comply with the FCC RF exposure compliance requirements, the separation

distance between the antenna and any person’s body (including hands, wrists, feet and

ankles) must be at least 8 inches (20.3 centimeters).

This transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter except those already approved in this filing.

The availability of some specific channels and/or operational frequency bands are country

dependent and are firmware programmed at the factory to match the intended destinations.

The firmware setting is not accessible by the end user.

Industry Canada (IC) Statement

This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the

following two conditions:

This device may not cause interference, and

This device must accept any interference, including interference that may cause undesired

operation of the device.

Chapter 1: Safety and Regulatory Information

PN 365-095-30000 x.2SURFboard SB8200 Cable Modem User Guide

CAN ICES-3 (B)/NMB-3 (B)

In Canada, RLAN devices are restricted from using the 5600-5650 MHz frequency band.

Caution: To reduce the potential for harmful interference to co-channel mobile satellite

systems, use of the 5150-5250 MHz frequency band is restricted to indoor use only.

High power radars are allocated as primary users (meaning they have priority) of 5250-5350

MHz and 5650-5850 MHz frequency bands. These radars could cause interference and/or

damage to License Exempt–Local Area Network (LE-LAN) devices.

IC Radiation Exposure Statement

Important Note: This equipment complies with IC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with a minimum

distance of 20 centimeters between the radiator and your body.

Avis D'Industrie Canada (IC)

Cet appareil est conforme à la réglementation RSS-210 d'Industrie Canada. Son utilisation est

assujettie aux deux conditions suivantes:

Cet appareil ne doit pas causer d'interférences et

Cet appareil doit accepter toute interférence reçue, y compris les interférences causant un

fonctionnement non désiré.

CAN ICES-3 (B)/NMB-3 (B)

Au Canada, les appareils de réseau local sans fil ne sont pas autorisés à utiliser les bandes de

fréquence 5600-5650 MHz.

Avertissement: afin de réduire les risques de brouillage préjudiciable aux systèmes de

satellites mobiles utilisant les mêmes canaux, les dispositifs fonctionnant dans la bande 5150-

5250 MHz sont réservés uniquement pour une utilisation à l'intérieur

Les radars à haute puissance sont définis en tant qu'utilisateurs principaux (c.-à-d. prioritaires)

des bandes de fréquences 5250-5350 MHz et 5650-5850 MHz. Ces radars peuvent causer de

l'interférence ou des dommages susceptibles de nuire aux appareils exempts de licence–

réseau local (LAN-EL).

Déclaration de IC sur L'Exposition aux Rayonnements

Note Importante: cet équipement est conforme aux limites d'exposition aux rayonnements

établies par IC pour un environnement non contrôlé. Cet équipement doit être installé et utilisé

de manière à maintenir une distance d'au moins 20 cm entre la source de rayonnement et

votre corps.

Chapter 1: Safety and Regulatory Information

PN 365-095-30000 x.2SURFboard SB8200 Cable Modem User Guide

Caring for the Environment by Recycling

When you see this symbol on an ARRIS product, do not dispose of the product with

residential or commercial waste.

Recycling your ARRIS Equipment

Please do not dispose of this product with your residential or commercial waste.

Some countries or regions, such as the European Union, have set up systems to

collect and recycle electrical and electronic waste items. Contact your local

authorities for information about practices established for your region. If collection

systems are not available, call ARRIS Technical Support at 1-877-466-8646 for

assistance.

PN 365-095-30000 x.2SURFboard SB8200 Cable Modem User Guide

Chapter 2

Getting Started

Introduction

The ARRIS SURFboard® SB8200 DOCSIS 3.1 Cable Modem provides significantly higher

downstream (send) and upstream (receive) Internet connection speeds over the broadband

connection on your home or small business network. You use your SB8200 to directly connect

a computer or router to your LAN through an Ethernet connection.

This guide provides instructions for installing and setting up your SB8200 to get it connected

on your home or small business network, and also for viewing the operational status and

network configuration settings of your SB8200.

In the Box

Before installing your SB8200, check that the following items are included in the box. If any

items are missing, please call ARRIS Customer Support at 1-877-466-8646 for assistance.

Table 1. SB8200 Package Contents

Item

Description

SB8200 Cable Modem

High-speed DOCSIS 3.1 cable modem

Power Supply

Power cord for an electrical wall outlet connection

Ethernet Cable

Standard Category 5 (CAT5e) or higher network

cable

Andere Handbücher für SURFboard SB8200

Inhaltsverzeichnis

Andere Arris Modem Handbücher

Arris

Arris Touchstone TM502 Bedienungsanleitung

Arris

Arris Touchstone TM402 Bedienungsanleitung

Arris

Arris touchstone TM1602 Bedienungsanleitung

Arris

Arris Touchstone CM550 Bedienungsanleitung

Arris

Arris CM82 Benutzerhandbuch

Arris

Arris Touchstone TM1602G Bedienungsanleitung

Arris

Arris Touchstone TM822 Bedienungsanleitung

Arris

Arris TG3452A Bedienungsanleitung

Arris

Arris Touchstone CM8200 Bedienungsanleitung

Arris

Arris Touchstone TM401 Bedienungsanleitung

Arris

Arris SURFboard SBG6580 Bedienungsanleitung

Arris

Arris SURFboard SB6183 Bedienungsanleitung

Arris

Arris Touchstone TM1602G Bedienungsanleitung

Arris

Arris TM602 Bedienungsanleitung

Arris

Arris Touchstone DTM602G Bedienungsanleitung

Arris

Arris Touchstone WTM652 Bedienungsanleitung

Arris

Arris Touchstone SBG6700-AC Bedienungsanleitung

Arris

Arris SURFboard SBG7580-AC QSG Bedienungsanleitung

Arris

Arris Touchstone TM502 Bedienungsanleitung

Arris

Arris Touchstone TM501 Bedienungsanleitung

Arris

Arris SURFboard SBG6900-AC Bedienungsanleitung

Arris

Arris SURFboard SB6121 Bedienungsanleitung

Arris

Arris SURFboard SB6183 Bedienungsanleitung

Arris

Arris SURFboard SB6190 Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung

Zoom

Zoom 1070 Series Bedienungsanleitung