ART2WAVE Ap20 Bedienungsanleitung

AP20 Installation Guide

1 Contents of the box and important features:

Factory Reset Switch

Power Port ENET 0 (Uplink Ethernet

Port, Power-over-Ethernet

enabled)

ENET 1 (Reserved

do not use)

9/16” Ceiling Rail Adapter

15/16” Ceiling Rail

Mount

Identity QR Code

Slots for 9/16” Ceiling

Rail Adapter

Ethernet Cable

Power Adapter,

cover and prong

Wall Mount Installation

Kit:

2 Phillips Screws

2 Sinkers

5 Mounting the Access Point

Note: Do not mount the access point until it is linked to your Art2Wave account.

You can mount the AP20 in the following ways:

• Ceiling mounting (with 15/16” or 9/16” rails)

• Wall mounting

• Desk mounting

2 Setting up your AP20 Access Point

3 Linking the Access Point to your Art2Wave account

3.1 Using your mobile device

3.2 Using the Website

4 Connecting the Access Point to your network and power supply

There are four steps to setting up an AP20 access point:

1. Linking the access point to your Art2Wave account

2. Connecting the access point to your network and power supply

3. Mounting the access point

4. Verifying connectivity

There are two ways to link your access point to your account: using your mobile device or using

the Art2Wave website.

By installing the Art2Wave mobile device app, you can scan the QR code on the back of the

access point and link it to your account. Information about the app is available at

http://art2wave.com. The mobile device app includes instructions for completing the process.

To link the access point to your account using the Website, sign into your account at

http://art2wave.com and follow the instructions in the Art2Wave web site to complete the

process.

Connect the access point to your network by plugging an Ethernet cable into the ENET 0 port.

Do not connect to the ENET 1 port (this port is reserved for future use).

The Access point is powered either by connecting the supplied power adapter to an AC wall

outlet or by connecting the ENET 0 port to a device that provides 802.3af Power-over-

Ethernet. If using the supplied power adapter, remove the cover and insert the prong as shown

in Section 1.

5.1 Tips for selecting a location

The best location for your access point is at the center of your wireless coverage area, within

line of sight of all wireless devices. To get the best performance, consider the following:

• Mount the access point as high as possible above any obstructions

• Do not mount the access point next to building support columns or any other

physical obstructions that may cause dead zones

• Do not mount the access point near any material that may absorb or reflect Wi-Fi

signals

This unit must be installed indoors. The unit, AC power adapter, and its

cables are not designed for outdoor use.

Warning

The figure below shows you how to clip the access point to a 15/16” ceiling rail. Printed

instructions on the back of the unit explain which clips to use.

5.2 Ceiling mounting to a 15/16” rail

Slide the Access point diagonally

over the rail and rotate until the

unit clicks into place.

Press thess clips in and turn to

dismount the Access Point

5.3 Ceiling mounting to a 9/16” rail

The figure below shows you how to use the adapter to clip the access point to a 9/16” ceiling

rail. Printed instructions on the back of the unit explain which clips to use.

1. Slide the adapter

into the clips on the

back on the unit.

2. With the adapter in place,

slide the Access Point

diagonally over the rail and

rotate until the unit clicks into

place.

Press these clips and turn to

dismount the Access Point

5.4 Wall mounting

The figure below shows you how to mount the access point to a wall using screws and sinkers.

Note: Screw center distance = 141mm.

6 Verifying connectivity

7 Tips and Troubleshooting

7.1 If your access point status light is flashing yellow

You can verify that the AP20 Access point is connected to your network by using either the

Art2Wave website, or mobile device app that you used to link the unit to your Account.

Check the Status LED to determine whether the access point is operating correctly. The

access point is properly installed and connected to the Art2Wave management services when

the LED turns solid blue after a few minutes.

When the access point is powered on, the Status LED should display the following sequence:

The access point cannot connect to the Art2Wave management services. This usually occurs

when the unit cannot get an IP Address from your network using DHCP and has switched to

Local Network Configuration mode.

Note: See the Tips and Troubleshooting section if the access point does not reach Solid blue.

For a full description of LED Status Description visit the Support website

(www.art2wave.com/support).

Unit has just received power and has started

booting

Solid red

(for less than 5 seconds)

Solid Yellow

(for less than a minute)

Blinking blue

(for less than a minute)

Solid blue

Unit is starting up. Or if the Factory Reset

switch has been pressed, the unit is

resetting to factory condition.

Access point is negotiating a connection

with Art2Wave management services in the

cloud.

Access point is successfully set up to be

managed by Art2Wave management

services in the cloud.

Status Description# LED

8 Learning More, Service, and Support

8.1 Online Resources

7.2 Resetting back to factory defaults

While in this mode, the access point will not pass data through the ENET 0 port and will

broadcast an SSID that contains a portion of the access point’s MAC Address. You can use

any Wi-Fi enabled device to connect to this SSID and configure the network settings for this

access point using a web browser

To connect to the access point using the Local Network Configuration interface:

1. Connect your Wi-Fi enabled device to the SSID in the form of “AP-XX:XX:XX” (where

X is a placeholder). You are successfully connected when the LED on the Access

Point becomes solid purple

2. Use your web browser to navigate to http://192.168.100.1

3. Follow the on-screen instructions

See the Support section (http://art2wave.com/support) for information about Local Network

Configuration.

Note: Local Configuration mode will only activate if the access point is in Factory Default

condition and has never connected to the Art2Wave management services in the cloud.

If the access point is disconnected from a power source, press and hold the reset button, and

connect power to the unit. The LED will turn solid white to indicate the unit is restoring itself to

Factory Defaults.

If the access point is connected to a power source, press and hold the reset button until the

LED turns solid white and then release. This will restore the unit to the factory default settings.

Our support website (http://art2wave.com/support) contains links to online resources available

to help you get the most out of your access point.

9 Legal Notice

EXCEPT FOR ANY WRITTEN EXPRESS WARRANTY WE MAY SEPARATELY OFFER TO YOU,

AND TO THE EXTENT PERMITTED BY LAW, THIS PRODUCT IS PROVIDED “AS IS” AND WE

SPECIFICALLY DISCLAIM ALL EXPRESS, STATUTORY AND IMPLIED WARRANTIES,

INCLUDING, BUT NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY, FITNESS FOR A

PARTICULAR PURPOSE, NON-INFRINGEMENT AND AGAINST HIDDEN OR LATENT

DEFECTS. IF WE CANNOT LAWFULLY DISCLAIM STATUTORY OR IMPLIED WARRANTIES,

THEN TO THE EXTENT PERMITTED BY LAW, ALL SUCH WARRANTIES SHALL BE LIMITED

IN DURATION TO THE DURATION OF ANY WRITTEN EXPRESS WARRANTY WE MAY

SEPARATELY OFFER TO YOU, AS APPLICABLE, AND TO REPAIR OR REPLACEMENT

SERVICE. SOME JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG A

STATUTORY OR IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT

APPLY TO YOU. WE ARE NOT RESPONSIBLE FOR DIRECT, SPECIAL, INCIDENTAL OR

CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR UNDER

ANY OTHER LEGAL THEORY. IN SOME JURISDICTIONS THE FOREGOING LIMITATION

DOES NOT APPLY TO DEATH OR PERSONAL INJURY CLAIMS, OR ANY STATUTORY

LIABILITY FOR INTENTIONAL AND GROSS NEGLIGENT ACTS AND/OR OMISSIONS, SO THE

ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU. SOME JURISDICTIONS DO

NOT ALLOW THE EXCLUSION OR LIMITATION OF DIRECT, INCIDENTAL OR

CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT

APPLY TO YOU.

8.2 Copyright and Trademark

the copyrighted and proprietary property of Art2Wave, Inc. Reproduction, distribution or

modification without the express, written permission of Art2Wave, Inc. is not permitted.

“Art2Wave” is a trademark of Art2Wave, Inc. All other trademarks are the property of their

respective owners.

8.3 Open Source Code

Certain Art2Wave products include open source software code subject to the GNU General

Public License (GPL) and other Open Source Licenses. For more information, see:

http://art2wave.com/opensource

11.1 FCC

10 AP20 Specifications and Safety Guidelines

11 Regulatory Compliance Information

Specifications:

Frequency Band: 2.4GHz and 5GHz

Standards: 802.11a, 802.11b, 802.11g, 802.1n, and 802.11ac specifications

Interfaces:

1 RJ-45 10/100/1000Base-T Gigabit Ethernet Uplink with 802.3af Power-over-Ethernet (PoE)

support (15.4W)

1 RJ-45 10/100/1000Base-T Gigabit Ethernet LAN

Simultaneous dual-band 802.11ac Wi-Fi

Environmental Specifications:

Operating Temperature: 0 to 40℃

Storage Temperature: -40 to 80℃

Relative Humidify (Operational): 10 to 90% RH (non-condensing)

Relative Humidity (Storage): 5 to 95% RH (non-condensing)

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one of

the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

FCC Caution: Any changes or modifications not expressly approved by the party responsible

for compliance could void the user's authority to operate this equipment. See 47 CFR 1.80.

Inhaltsverzeichnis

Andere ART2WAVE Drahtloser Zugangspunkt Handbücher

ART2WAVE

ART2WAVE A20 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

ART2WAVE ap20 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken