Aruba 228 Series Bedienungsanleitung

Aruba 228 Series Wireless Access Points

Installation Guide

Rev04 | August 2018 1

The Aruba AP-228 is a fully temperature hardened, water resistant, indoor rated, dual-radio IEEE

802.11ac wireless access point. This access point use MIMO (Multiple-in, Multiple-out) technology and

other high-throughput mode techniques to deliver high-performance, 802.11ac 2.4 GHz and 5 GHz

functionality while simultaneously supporting existing 802.11a/b/g/n wireless services. The AP-228

access point works in conjunction with an Aruba controller, while the IAP-228 access point can be

configured using a built-in virtual controller.

Operations

Wireless transceiver

Wireless access point (IEEE 802.11 a/b/g/n/ac)

Wireless air monitor (IEEE 802.11 a/b/g/n/ac)

Protocol-independent networking functionality

Compatibility with IEEE 802.3at PoE

Package Contents

228 SeriesAccess Point

Cable Glands x2

USB Console Cable

Copper Lug x1

M4 x 8 Screw x1

Startup Guide

The weatherproof caps for Ethernet and Console interfaces are connected to the AP, not loose in the package.

Mounting kits for use with the 228 Series access points are sold separately. Contact your Aruba sales

representative for details.

Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton,

including the original packing materials. Use these materials to repack and return the unit to the supplier if

needed.

2Aruba 228 Series Wireless Access Points | Installation Guide

Hardware Overview

Figure 1 Front View

Figure 2 Bottom View

LED

The 228 Series is equipped with one LED that indicates the system status of the AP.

2G0

2G1

2G2

5G0

5G1

5G2

E0/POE

Grounding Point

USB Console Port, Reset button and LED

CAUTION

External antennas for this device must be installed by an Aruba Certified Mobility Professional (ACMP) or other

Aruba-certified technician, using manufacturer-approved antennas only.

The Equivalent Isotropically Radiated Power (EIRP) levels for all external antenna devices must not exceed the

regulatory limit set by the host country/domain.

Installers are required to record the antenna gain for this device in the system management software.

Les antennes externes pour cet appareil doivent être installées par un professionnel de la mobilité certifié Aruba

(ACMP) ou un autre technicien certifié Aruba, en utilisant uniquement des antennes approuvées par le fabricant.

Les niveaux équivalents de puissance à rayonnement isotrope (EIRP) pour tous les périphériques d'antenne

externe ne doivent pas dépasser la limite réglementaire définie par le pays hôte / domaine.

Les installateurs doivent enregistrer le gain d'antenne pour cet appareil dans le logiciel de gestion du système.

Aruba 228 Series Wireless Access Points | Installation Guide 3

Table 1 LED Meanings during Boot Up

Table 2 LED Meanings during Operation

USB Console Port

The USB Micro-B console port allows you to connect the AP to a terminal or a laptop for direct local

management. Use the included USB console cable to connect the AP. You can download the

necessary driver for USB-UART adapter from support.arubanetworks.com under the Tools &

Resources tab.

Use the following setting to access the terminal:

Ethernet Ports

228 Series is equipped with two10/100/1000Base-T (RJ-45) Gigabit Ethernet ports (E0/POE and E1) for

wired network connectivity. The E0/POE port supports 802.3at Power over Ethernet (PoE), accepting

48 VDC (nominal) as a standard defined Powered Device (PD) from a Power Sourcing Equipment (PSE)

such as a PoE midspan injector.

These ports have RJ-45 female connectors with the pin-outs shown in Figure 3.

LED Color/State Meaning

System LED Off No power to AP

Red Initial power-up

Green - Flashing AP booting

Green - Steady AP ready and 1000Mbps Ethernet link established. The LED

turns off after 1200 seconds

Green - Yellow, 6 seconds

period AP ready and 10/100Mbps Ethernet link established. The LED

turns off after 1200 seconds

LED Color/State Meaning

System LED Solid Red General fault

One blink off every 3

seconds Radio 0 fault (5 GHz)

Two quick blink off 0.5

seconds apart cycled every

3 seconds

Radio 1 fault (2.4GHz)

Table 3 Console Settings

Baud Rate Data Bits Parity Stop Bits Flow Control

9600 8 None 1 None

4Aruba 228 Series Wireless Access Points | Installation Guide

Figure 3 Gigabit Ethernet Port Pin-Out

Reset Button

The reset button can be used to return the AP to factory default settings. To reset the AP:

1. Power off the AP.

2. Press and hold the reset button using a small, narrow object, such as a paperclip.

3. Power-on the AP without releasing the reset button. The system LED will flash within 5 seconds.

4. Release the reset button.

The system LED will flash again within 15 seconds indicating that the reset is completed. The AP will

now continue to boot with the factory default settings.

Grounding Point

Always remember to protect the AP by installing grounding lines. The ground connection must be

complete before connecting power to the AP enclosure.

Figure 4 Rear View

Before You Begin

1000Base-T Gigabit

Ethernet Port

RJ-45 Female

Pin-Out

Signal Name

BI_DC+

BI_DC-

BI_DD+

BI_DD-

BI_DA+

BI_DA-

BI_DB+

BI_DB-

Function

Bi-directional pair +C, POE Positive

Bi-directional pair -C, POE Positive

Bi-directional pair +D, POE Negative

Bi-directional pair -D, POE Negative

Bi-directional pair +A, POE Negative

Bi-directional pair -A, POE Negative

Bi-directional pair +B, POE Positive

Bi-directional pair -B, POE Positive

CAUTION

FCC Statement: Improper termination of access points installed in the United States configured to non-US

model controllers will be in violation of the FCC grant of equipment authorization. Any such willful or

intentional violation may result in a requirement by the FCC for immediate termination of operation and may

be subject to forfeiture (47 CFR 1.80).

Aruba 228 Series Wireless Access Points | Installation Guide 5

Pre-Installation Network Requirements

After WLAN planning is complete and the appropriate products and their placement have been

determined, the Aruba controller(s) must be installed and initial setup performed before the Aruba

APs are deployed.

For initial setup of the controller, refer to the ArubaOS Quick Start Guide for the software version

installed on your controller.

Pre-Installation Checklist

Before installing your AP, be sure that you have the items listed below:

Gigabit Ethernet cable of required length

IEEE 802.3at compliant PoE source

For AP-228 only:

Aruba Mobility Controller configured and installed on the network

Layer 2/3 network connectivity to your AP

One of the following network services:

Aruba Discovery Protocol (ADP)

DNS server with an “A” record

DHCP Server with vendor specific options

CAUTION

EU Statement:

Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the ArubaOS User Guide/

Aruba Instant User Guide for details on restrictions.

Produit réseau local radio basse puissance operant dans la bande fréquence 2.4 GHz et 5 GHz. Merci de vous

referrer au ArubaOS User Guide/Aruba Instant User Guide pour les details des restrictions.

Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet. Weitere Informationen bezlüglich

Einschränkungen finden Sie im ArubaOS User Guide/Aruba Instant User Guide.

Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare riferimento alla ArubaOS User Guide/

Aruba Instant User Guide per avere informazioni detagliate sulle restrizioni.

CAUTION

To meet regulatory restrictions, the access point must be professionally installed.

The instructions for this section are applicable to the AP-228 only.

Aruba Networks, Inc. in compliance with governmental requirements, has designed the AP-228 such that only

authorized network administrators can change configuration settings. For more information about AP

configuration, refer to the ArubaOS Quick Start Guide /Aruba Instant Quick Start Guide and ArubaOS User Guide/

Aruba Instant User Guide.

6Aruba 228 Series Wireless Access Points | Installation Guide

Verifying Pre-Installation Connectivity

Before you install APs in a network environment, make sure that the APs will be able to locate and

connect to the controller when they are powered on.

Specifically, you must verify the following conditions:

When connected to the network, each AP is assigned a valid IP address.

APs can locate the controller.

Refer to the ArubaOS Quick Start Guide for instructions on locating and connecting to the controller.

Identifying Specific Installation Locations

Use the AP placement map generated by Aruba’s RF Plan software application to determine the

proper installation location(s). Each location should be as close as possible to the center of the

intended coverage area and should be free from obstructions or obvious sources of interference.

These RF absorbers/reflectors/interference sources will impact RF propagation and should have been

accounted for during the planning phase and adjusted for in RF plan.

Identifying Known RF Absorbers/Reflectors/Interference Sources

Identifying known RF absorbers, reflectors, and interference sources while in the field during the

installation phase is critical. Make sure that these sources are taken into consideration when you

attach an AP to its fixed location. Examples of sources that degrade RF performance include:

Cement and brick

Objects that contain water

Metal

Microwave ovens

Wireless phones and headsets

Installing the AP

Using the AP-220-MNT-W1 Mount Kit

The 228 Series access point can be installed on a wall by using AP-220-MNT-W1 mount kit.

CAUTION

Access points are radio transmission devices and as such are subject to governmental regulation. Network

administrators responsible for the configuration and operation of access points must comply with local

broadcast regulations. Specifically, access points must use channel assignments appropriate to the location in

which the access point will be used.

The instructions for this section are applicable to the AP-228 only.

Service to all Aruba products should be performed by trained service personnel only.

The 228 Series access point does not ship with any mount kit. The AP-220-MNT-W1 mount kit is available as

accessories and must be ordered separately.

Aruba 228 Series Wireless Access Points | Installation Guide 7

1. Begin by attaching the wall mount adapter to the wall.

a. Install any necessary wall anchors. Wall anchors are not included in this kit.

b. Align the screw holes in the mounting bracket with the previously installed anchors or

demarcated screw points.

c. Insert the screws to secure the mounting bracket. Screws are not included in this kit.

Figure 5 Attaching the Adapter to a Wall

Figure 6 Attaching the Adapter to a Wall (Alternate)

2. Attach necessary cables and/or antennas to the AP.

3. Attach the AP to the secured mounting adapter as shown in Figure 7.

a. Align the AP with a mounting adapter, placing the AP so that it’s mounting tabs are at an angle

of approximately 30 degrees to the adapter.

4. Pushing toward the wall, rotate the AP clockwise until it clicks into place (see Figure 7).

For details on AP-220-MNT-W1, please refer to the AP-220-MNT-W1 Installation Guide.

AP-220_11

AP-220_14

8Aruba 228 Series Wireless Access Points | Installation Guide

Figure 7 Attaching the AP to the Mounting Bracket

Figure 8 Completed Installation

Grounding the AP

The grounding must be completed before powering up the AP. The grounding wire should be #8

AWG.

1. Peel the cover of one end of the grounding wire and place the bare grounding wire into the

included copper lug, and press firmly with the crimping pliers.

2. Fasten the copper lug to the grounding hole on the AP with the included M4 x8 screw.

Connecting the Ethernet Cable

To connect the Ethernet cable to the AP, perform the following steps using the cable glands that ships

with your AP.

WARNING

Failure to use the included Ethernet cable glands can lead to connectivity and POE issues.

Aruba 228 Series Wireless Access Points | Installation Guide 9

Figure 9 Installing a Cable Gland

1. Slide the sealing nut over the cable (without the RJ45 connector attached to the end).

2. Slide the clamping ring over the cable.

3. Using a crimping tool, attach the shielded RJ45 connector to the end of the cable.

4. Remove the weatherproof cap on the Ethernet port.

5. Insert the RJ45 connector to the Ethernet port.

6. Screw the clamping ring onto the Ethernet port.

7. Screw the sealing nut onto the clamping ring.

Verifying Post-Installation Connectivity

The integrated LEDs on the AP can be used to verify that the AP is receiving power and initializing

successfully (see Table 1 and Table 2). Refer to the ArubaOS Quick Start Guide for further details on

verifying post-installation network connectivity.

Configuring the AP

AP Provisioning/Reprovisioning

Provisioning parameters are unique to each AP. These local AP parameters are initially configured on

the controller which are then pushed out to the AP and stored on the AP itself. Aruba recommends

that provisioning settings be configured via the ArubaOS Web UI only. Refer to the ArubaOS User

Guide for complete details.

AP Configuration

Configuration parameters are network or controller specific and are configured and stored on the

controller. Network configuration settings are pushed out to the AP(s) but remain stored on the

controller.

Configuration settings can be configured via the ArubaOS Web UI or ArubaOS CLI. Refer to the

ArubaOS User Guide for complete details.

The cable is not included and must be purchased separately. Purchase a suitable UV-resistant, outdoor rated,

CAT 5E or better RJ45 cable for use with the AP.

Sealing Nut Clamping Ring CAT 5E or Better Cable

Seals

The seals inside the clamping ring by factory default is applicable for cables with 5-8.5 mm diameter. In the

cable gland kit, another seals is provided for use with the cables with 7-10 mm diameter.

The instructions for this section are applicable to the AP-228 only.

10 Aruba 228 Series Wireless Access Points | Installation Guide

Product Specifications

Mechanical:

Device Dimensions (HxWxD): 8.7 inches x 5.9 inches x 2.6 inches (221mm x 150mm x 66mm)

Electrical

Ethernet

2 x 10/100/1000Base-T auto-sensing Ethernet RJ-45 Interfaces

MDI/MDX

Power over Ethernet (IEEE 802.3at compliant), 48VDC(nominal) /0.6A

Power

POE support on WAN port: 802.3at-compliant POE sourcing devices

Environmental

Operating

Temperature: -40ºC to 60ºC (-40ºF to 140ºF)

Humidity: 5% to 95% non-condensing

Storage

Temperature: -40ºC to 70ºC (-40ºF to 158ºF)

For additional specifications on this product, please refer to the data sheet. The data sheet can be

found at www.arubanetworks.com.

Inhaltsverzeichnis

Andere Aruba Drahtloser Zugangspunkt Handbücher

Aruba

Aruba A200 Bedienungsanleitung

Aruba

Aruba AP 70 Bedienungsanleitung

Aruba

Aruba Instant On AP22 Bedienungsanleitung

Aruba

Aruba 203R Series Bedienungsanleitung

Aruba

Aruba IAP-274 Bedienungsanleitung

Aruba

Aruba 65 Bedienungsanleitung

Aruba

Aruba RAP-2WG Bedienungsanleitung

Aruba

Aruba RAP-5WN Bedienungsanleitung

Aruba

Aruba AP-303H Series Bedienungsanleitung

Aruba

Aruba 300 series Bedienungsanleitung

Aruba

Aruba 310 Series Bedienungsanleitung

Aruba

Aruba 560EX Series Bedienungsanleitung

Aruba

Aruba 570 Series Bedienungsanleitung

Aruba

Aruba 310 Series Bedienungsanleitung

Aruba

Aruba 303P Series Bedienungsanleitung

Aruba

Aruba AP-505H Bedienungsanleitung

Aruba

Aruba 210 Series Bedienungsanleitung

Aruba

Aruba AP-105 Bedienungsanleitung

Aruba

Aruba AP-68P Bedienungsanleitung

Aruba

Aruba 570EX Series Bedienungsanleitung

Aruba

Aruba 303 Series Bedienungsanleitung

Aruba

Aruba Instant On AP11 Bedienungsanleitung

Aruba

Aruba AP-92 Bedienungsanleitung

Aruba

Aruba AP-130-MNT-C2 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung

EnGenius

EnGenius EAP350 Bedienungsanleitung