ARX AFW-1 Bedienungsanleitung

Anti-Feedback

Workstation

OWNER’S

MANUAL

AFW-1

ARX Systems Pty Ltd, PO Box 15,

Cheltenham, Victoria 3192, Australia

Phone: 03 - 9555 7859 Fax: 03 - 9555 6747

International Fax: +61-3 -9555 6747

On the Web: http://www.arx.com.au

Email: [email protected]

INTERNATIONAL LIMITED WARRANTY

ARX Systems (ARX) warrants to the first purchaser of any ARX equipment that it is

free from defects in materials and workmanship under normal use and service.ARX’s

sole obligation under this warranty shall be to provide, without charge, parts and

labour necessary to remedy defects, if any, which appear within twelve (12) months

from date of purchase, and for a further twelve (12) months supply parts only.

This is our only warranty. It does not cover finish or appearance items, or if the

equipment has been, in ARX’s sole judgement:

•Subjected to misuse, abuse, negligence or accident;

•Repaired, worked on, or altered by persons not authorized by ARX;

•Connected, installed, adjusted or used for a purpose other than that for which

it was designed.

Some states do not allow the exclusion or limitation of incidental or consequential

damages so some of the above exclusions may not apply to you.This warranty gives

you and us specific legal rights and you may also have other rights which may apply.

Warranty Service Procedure

Should it become necessary to have your equipment serviced under the terms

of the warranty, please follow these steps:

1. Call your ARX distributor for a Return Authorization (RA) number;

2. Carefully repack the unit, in its original packaging where possible,

including a note with a description of the problem, and a copy of the

receipt showing date of purchase. Attach these to the actual unit

itself. Don’t forget to write your name and address clearly, and in-

clude a phone number where you can be contacted during normal

business hours. Make it easy for our service technicians to contact

you if they have a question. Also, use plenty of packing material -

better to be safe than sorry.

3. Send the unit freight prepaid to ARX Systems, at the address given

you with your RA number. We will pay the return freight when the

serviced unit is returned to you.

4. We strongly recommend you insure the package. We can’t fix it if it

gets lost! Send it by UPS, Fedex, or any similar service that can track

the package. Parcel Post is not recommended

If Warranty Registration Card is missing, please write to ARX in the country of

purchase, stating model and where purchased, or to ARX, PO Box 15, Cheltenham,

Victoria 3192, Australia.

This symbol indicates that a Slow Blow fuse is used in this equip-

ment. Replace with same type and value only

This symbol is intended to alert you to the presence of uninsulated

dangerous voltage within the product's enclosure that may be of

sufficient magnitude to constitute a risk of electric shock.

This symbol is intended to alert you to the presence of important

operating instructions contained in this owner's manual

WARNING SYMBOLS USED ON THIS EQUIPMENT

IMPORTANT -

PLEASE READTHIS FIRST

This is a dual voltage unit. It is essential that you check that the voltage

on the fuseholder cover below the AC connector on the rear of the chassis

is set correctly before connecting it to AC power.

To change, pull fuseholder out and rotate 180o, then push in again. Do not

insert power cable into unit until voltage has been correctly set. Do not plug

power cable into AC power until voltage has been correctly set

THIS IS SET FOR

100 V AC TO 120 V

AC OPERATION

THIS IS SET FOR

220 V AC TO 240 V

AC OPERATION

Complieswith89/336/EECElectromagnetic

CompatibilityDirective,amendedby92/31/

EECand93/68/EEC andmeetsthe follow-

ing standards:EN 55013 : 1990, Sections

3.2and3.5EN55020:1988,Sections4.3,

5.4, 6.2, 7.0, 8.0.

Non-Volatile Memory

A complete record of the Anti Feedback filter settings is stored automatically in the

AFW-1 when you power down the system. Upon power-up, the system automati-

cally reloads the filters and returns them to the same position and depth as they

were when the power was turned off.

Filter Reset

If the sound system’s setup has changed, such as a different venue, change of equip-

ment, significant movement of microphones or speakers, or any other change that

would cause the feedback points to change, theAnti Feedback section must be reset.

Most Important The AFW-1 should not be RESET during a program. The system’s

master volume should always be set to a minimum volume before clearing the fil-

ters. Otherwise high volume feedback may occur, with potentially damaging re-

sults.

Bypass switches

The Active/Bypass switch under the SET ANTI FEEDBACK section of the front

panel will bypass the Anti Feedback, the Limiter control, and the Output level con-

trol, leaving just the EQ section active.

The Active/Bypass switch under the SET SYSTEM section is a true hardwire bypass

for the complete unit, and connects the inputs directly to the outputs, bypassing all

circuitry.

FBX Feedback Exterminator is a Registered Trademark of Sabine, Inc, and is the brand name of its line of automatic

feedback controllers.Covered by US Patent No.5,245,665, Australian Patent No. 653,736, and Canadian patent No.

2,066,624-2.Other patentspending.ARX ® isaRegisteredTrademark of ARXSystemsPty Ltd.Allothertrademarks

are the property of ARX Systems.

ARX policy is one of continuous improvement, and therefore designs may change without notice.However, unless

otherwise stated, specifications will always equal or exceed those previously given.

Introduction

Thank you for choosing this ARX AFW-1 Anti-Feedback Workstation. It’s a

great product, and we hope you enjoy using it as much as we enjoyed creat-

ing it. As with all ARX equipment, it has undergone extensive factory cali-

bration and ‘burn in’ before shipping. Since it involves a few radical depar-

tures from the normal way that we think of equalizers, for continued trouble

free use please familiarise yourself with the contents of this manual before

using the AFW-1 Anti-Feedback Workstation.

About the AFW-1

Tuning a live sound system, whether it’s a concert or a conference or all

points in between, is a complex procedure at the best of times! Stopping

feedback is only a part of it - you still need to adjust the actual sound of the

system in the room.

In the ideal world you’d have an equalizer to set the system curve, some-

thing to eliminate feedback, and something else to keep the system level

under control.

So, we’d like to introduce you to the ARX contribution to the ideal world -

the all-new ARX AFW-1 Anti Feedback Workstation. A single channel unit

incorporating a 30 band graphic equalizer, a smooth sounding peak limiter,

and onboard genuine Sabine FBX Feedback Exterminator circuitry.

Want total control over everything? You’ve got it.

Want automatic feedback locating and suppressing? You’ve got that too.

Want a safety valve that’ll keep your system in one piece? You’ve got that as

well. All integrated into one 2 RU package, all designed to work with each

other, and with you.

If the system is in a fixed installation, simply power everything down when

you’ve finished. The AFW-1 remembers your anti-feedback settings next

time it is used - there’s no need to reset the circuit when it is turned back on.

The ARX AFW-1 Anti Feedback Workstation has an application for every

mode of live audio: Monitors, Front of House, Church installations, TV au-

dience monitors, Conferences; in fact, anywhere there’s a live microphone,

there’s a need for the AFW-1.

In the next few pages you’ll discover how to set up your AFW-1, where to

use it, and how to get the most out of it.

Please take the time to read this manual. If you can’t wait, then go straight

to Page 4 and at least read the Quick Reference Guide. It’ll get you started.

Setting up the AFW-1

Setting up the AFW-1 correctly requires that certain steps are taken, in a particular

order. Technical people may call this the System Initializing Procedure, but we’ll just

call it Setup.

1. To install the AFW-1 in a sound system, connect it wherever a Graphic EQ

would go. For example, between the Mixing console and the Power amps. If

you are using multiple AFW-1’s in a monitor rig, then connect one between

each monitor send and crossover/amplifier

2. Place the speakers and microphones in the positions where they will be used

during the performance. Don’t place the microphones facing into the speakers!

3. Turn on the system

4. Set the Limiter Threshold at -10dB. The process of setting up the AFW-1 will

induce feedback rings, and the limiter will keep these from damaging the

system

5. Check that the Anti Feedback ACTIVE and Unit ACTIVE switches are pressed

IN and not Bypassed

6. Adjust the EQ section of the AFW-1 to set the system curve that you want. DO

NOT NOTCH FOR FEEDBACK. The EQ sliders should form a smooth curve

7. Set the channel levels on the console at the performance level. Reduce mixing

console master levels

8. Press and hold down the switch marked ‘PRESS AND HOLD FOR 4 SECONDS

TO RESET’ on the front of the AFW-1 for 4 seconds to clear out filters set

previously.

9. Place the AFW-1 in the active mode by releasing RESET. This procedure is

required to set the FIXED filters on the system’s resonating frequencies

10. SLOWLY bring up the console’s master sliders until feedback starts to occur.

The AFW-1 will detect and quickly remove it

11. Continue slowly raising the system master volume until the system is just over

the level required for the performance. Now back off the master volume

slightly so the system is not on the brink of another feedback point

12. The AFW-1 is now ready for use. It will lock these fixed filters on the feedback

frequencies, and leave a further 3 filters ‘floating’, to pull out any other

feedback during the performance if it occurs

13. Reset the Limiter at say, +3dB, or the maximum safe level of your system

14. The Clip LED may flash on transients - this is normal. But if it is lit continually,

then the level through the unit is too high and should be reduced. To do this,

bring down the master faders on the console a little, and bring up the output

gain of the AFW-1 by the same amount. Perhaps you have the Limiter set too

low, so it’s continually on. Or you could try increasing the crossover output

slightly. You could also make sure the amplifiers are on their maximum level.

Or you may have too little system for the sound pressure level you want in too

big a room. That’s one thing we can’t fix!

AFW-1 QUICK REFERENCE GUIDE

If you can’t wait to use the AFW-1, at least read this page first!

1. To install the AFW-1 in a sound system, connect it wherever a

Graphic EQ would go. For example, between the Mixing console and

the Power amps

2. Connect up and position the speakers and microphones where they

will be used during the performance. Don’t place the microphones

facing into the speakers!

3. Set the Limiter Threshold at -10dB

4. Check that the Anti Feedback ACTIVE and Unit ACTIVE switches

are pressed IN and not Bypassed

5. Adjust the EQ section of the AFW-1 to set the system curve that you

want. DO NOT NOTCH FOR FEEDBACK. The EQ sliders should

form a smooth curve.

6. Set the channel levels on the console at the performance level. Reduce

mixing console master levels

7. Press the switch marked ‘PRESS AND HOLD FOR 4 SECONDS TO

RESET’ on the front of the AFW-1 for 4 seconds

8. SLOWLY bring up the console’s master faders until feedback starts to

occur. The AFW-1 will detect and quickly remove it.

9. Continue increasing the master level until the required volume level

is reached

10. The AFW-1 is now ready for use. It will lock these feedback

frequencies, and leave a further 3 filters ‘floating’, to pull out any

other feedback during the performance if required

11. Reset the Limiter at +3dB or the maximum safe level of your system

12. The Clip LED may flash on transients - this is normal. But if it is lit

continually, then the level through the unit is too high and should be

reduced

13. The AFW-1 will remember its settings the next time it is turned on

and will not need resetting if the room or system has not changed.

14. For best results the unit should be reset if there has been any change

in the room or system that may change the feedback characteristics

15. Don’t reset the unit during the performance!

The result is that the overall program gain is increased 6 or more dB and provides

much clearer and more natural sounding speech and music. And since it is fully

automatic, no operator is required.

The digital filters inside theAFW-1 are switchable between 1/5th octave and 1/10th

octave. 1/5th is recommended for speech applications, such as conferences, speech-

es, etc, and 1/10th is recommended for music applications.

Before changing this switch, you must first power down the system. Then switch

the filter to the setting required. Power up the system again, and during its turn on

self test the AFW-1 will change the filter setting. The system should be RESET after

doing this, by following the Setup procedure detailed below.

About the Filters

The Anti Feedback section has two types of filters - fixed and dynamic.

Fixed filters retain their frequency center points in memory until the unit is reset by

the user. These filters are set in the AFW-1 initialization procedure by the strongest

resonating frequencies to provide the system’s gain before feedback.

Dynamic filters control intermittent feedback that comes and goes throughout the

performance, such as feedback from moving wireless microphones, getting too close

to speakers, monitors, that sort of thing. They are automatically reassigned to new

frequencies as feedback occurs on a first in - first out protocol.

The Anti Feedback section circuitry has a total of 9 filters; 6 fixed and 3 dynamic

filters. This has proven to be the best combination for most applications.

Where To Install The AFW-1 In The Signal Path.

The Limiter Section

The Peak Limiter in the AFW-1 has been included to let you set an absolute ceiling

on the output level.

Its attack and release times are program dependent and have been optimized to

appear as transparent to the ear as possible.

However, remember that it is a Limiter, and should be set at a level that coincides

with the onset of clipping in the system, where ideally it is not going to be active for

the bulk of the time.

TheAFW-1 can be placed anywhere

in the system that a line level signal

is available. However, best results

are obtained if it is placed last in the

chain before the power amplifiers.

If you are using a 2 or 3 way or more

system, with an active crossover

before the amps, then naturally the

AFW-1 will go before the crossover

AFW-1 Specifications

Input Impedance

20 K Ohm Balanced

Output Impedance

300 Ohm Balanced

Nominal Operating Level

+4dB

Maximum Input Level

+20 dB

Maximum Output Level

+20 dB

Dynamic Range

110 dB

Signal to Noise Ratio

-90dB Unweighted

Distortion

0.01% @ 1 KHz, +4dB

Frequency Response

20 Hz to 20 KHz, 0.5 dB

Equalizer Filters

30 x 1/3rd octave Constant Q on standard

ISO frequencies

Equalizer Range

±10dB cut or boost

FBX Filters

6 fixed, 3 dynamic

FBX Filter Range

51Hz to 17 KHz

FBX Filter Width

Switchable 1/5th or 1/10th octave

FBX Filter Depth

0dB to -40dB

Peak Limiter Threshold

-10 dB to +10 dB, user variable

Limiter Status Metering

Amber LED: Limiter Active

AC requirements

90-120 or 220-240 VAC, 50-60Hz, 18 VA

Size 482 x 88 x 230 mm

19”W x 3½”H x 9”D

AFW-1 Reference Guide

Graphic Equalizers are great products, and are extremely useful tools for profes-

sional audio engineers. But, they do require a fair degree of knowledge to operate

them successfully.

Feedback Exterminators are great, too, because they automatically find frequencies

that are feeding back and pull them down. But, that’s all they do. You can’t tune the

system with them - for that, you need an equalizer, usually a Graphic Equalizer.

In the ARX AFW-1 Anti-Feedback Workstation, we’ve combined the two products

described above, to give users the best of both worlds. An equalizer, to tune the

sound of the room/system, and an FBXAnti Feedback to automatically pull out any

feedback.

And, as a very useful added bonus, we’ve included a smooth sounding Peak Limit-

er to ensure that the signal stays within the level that you decide.

So let’s work our way through the operation of the AFW-1, from start to finish.

The Equalizer Section

The EQ section of the AFW-1 has been designed without compromise as a totally

accurate professional third octave equalizer, with innovative ‘Constant Q’ circuitry.

Constant Q is a true WYSIWYG (WhatYou See Is What You Get) design concept that

allows far more accuracy in EQ control.

Its 30 smoothly damped, centre grounding sliders can be adjusted to give a maxi-

mum of 10dB cut or boost. The Q of the filter has been specifically optimised to

allow easy combining of the filters. This enables you to set up a musical, notch free

system curve.

Using the EQ section

The idea of the EQ section is to ‘tune’ the room to the system, and to ‘tweak’ the

response a little so that it sounds good. We’re not going to use it to notch out feed-

back - we’ve got the Anti Feedback section for that - but to adjust the overall sound

of the system so it doesn’t sound ‘boomy’ or ‘harsh’. So, play a tape or CD that

you’re very familiar with, and adjust the sliders on the EQ section so that the system

sounds ‘just right’.

Note that a little EQ is a lot, so use each fader gently. Avoid any sudden dips or

peaks - that’s not what it’s there for. The look of the sliders should resemble a smooth

curve. If you don’t need to move it, then leave it.

Avoid too much boost at lower frequencies. Very few systems can deliver much

response below 30 Hz, so it’s pointless pushing those sliders up. However 50 to

100Hz can often benefit from a little boost, as can 10KHz. Between those points it

should be a smooth succession of gentle curves.

The Anti Feedback section

The Anti Feedback section of the AFW-1 is essentially a computer controlled para-

metric equalizer which continuously searches for feedback. Once feedback is detect-

ed, it extinguishes the feedback automatically by inserting a very narrow notch fil-

ter directly on the feedback frequency, only as deep as necessary to control the feed-

back. It finds and eliminates feedback typically in less than one second.

Front Panel Controls

1. 30 smoothly damped, centre grounding sliders

per channel, on standard ISO frequencies

2. Reset control for Feedback Exterminator

circuitry

3. Clip LED indicates imminent clipping,

monitored at all vital stages throughout the

AFW-1

4. Active/Bypass switch for Feedback

Exterminator, Limiter and Output level

controls

5. Limiter Threshold and Limit LED

6. Hardwire Active/Bypass switch for unit

7. Power LED indicates AFW-1 is connected to

AC power

Rear Panel Connectors

1. Balanced Input TRS socket. Tip + HOT, Ring —

COLD, Sleeve GROUND

2. Balanced Input XLR type. Pin 2 + HOT, Pin 3 —

COLD, Pin 1 GROUND

3. Balanced Output XLR type (same wiring as Input)

4. Balanced Output TipRingSleeve jack socket (same

wiring as Input)

5. Feedback Exterminator filter width switch

6. Audio Ground Lift switch

7. IEC 3 pin AC connector and integral fuseholder.

RISK OF FIRE - Replace fuse with correct value

only: 90 - 120 V AC 1 amp, 220-240 V AC 0.5 amp.

Please also refer to voltage details on Page 2

Andere ARX Desktop Handbücher

ARX

ARX AFW30 Bedienungsanleitung

Beliebte Desktop Handbücher anderer Marken

HP m9060n - Pavilion - Elite Technisches Datenblatt

Asus

Asus E210 Series Bedienungsanleitung

Dell

Dell Inspiron 600m Bedienungsanleitung

Dell

Dell Inspiron 3662 Bedienungsanleitung

TotalFlow

TotalFlow uFLO Bedienungsanleitung

HP Presario SV7000 - Desktop PC Bedienungsanleitung

HP ProDesk 400 G5 Handbuch

Logitech

Logitech MK320 Bedienungsanleitung

Dell

Dell XPS 730 H2C Bedienungsanleitung

Sony

Sony Vaio Series Bedienungsanleitung

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Bedienungsanleitung

Alto

Alto MD 250 Bedienungsanleitung

Arbor Technology

Arbor Technology FPC-7800 Series Bedienungsanleitung

Sony

Sony VAIO VGX-TP1 Series Bedienungsanleitung

Asus

Asus Eee Box B204 Bedienungsanleitung

Dell

Dell Optiplex 9010 All In One Bedienungsanleitung

HP Z1 Bedienungsanleitung

Everex

Everex eXplora Bedienungsanleitung