ASA Electronics APM-202B Bedienungsanleitung
Controller
Product Introductions
APM-202B
APM-302B
APM-302C
APM-352B
ASA TOOLS ENTERPRISE CORP.
2F-1., NO. 346, Sec 6, Nanjing E. Rd., Neihu Dist.,
Taipei city, Taiwan, 11470
Tel: +886-2-27900535
Fax: +886-2-27949952
Email: asaswdvr@ms16.hinet.net
Website: www.asa-tool.com
1
Table of Content
■Special Thanks to our customer
Thank you for choosing our light and powerful electric screwdrivers. To ensure the tool fully utilizes its
maximum performance and extend its life, please read this manual before use.
-Table of Content-
General Safety Warnings ..................................................................................................... 03
Read before use ..................................................................................................................... 04
Declaration of Conformity CE/UKCA/Service...................................................................... 05
Product information ............................................................................................................. 06
Operation ............................................................................................................................... 07
Troubleshooting ………………………………………………………………………......... 12
Assembly Drawing …………………………………………………...….……………..…… 13
Parts List …………………………………………………………………………...…………
02
04
06
07
08
14
16
17
2
General Safety Warnings
■General Safety Warnings
WARNING: Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future reference.
■Work area safety
-Keep work area clean and well lit. Cluttered or dark areas invite accidents.
-Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the dust or fumes.
-Keep children and bystanders away while operating a power tool. Distractions can cause you to lose
control.
■Electrical safety
-Power tool plugs must match the outlet. Never modify the plug in any way. Unmodified plugs and
matching outlets will reduce risk of electric shock.
-Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is earthed or grounded.
-Do not expose power tools to rain or wet conditions. Water entering a power tool/its adaptor will increase
the risk of electric shock.
-Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord
away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric
shock.
-When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
-If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)
protected supply for its adaptor. Use of an RCD reduces the risk of electric shock.
■Personal safety
-Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a
power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in serious personal injury.
-Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
-Carrying power tools with your finger on the switch or energizing power tools that have the switch on
invites accidents.
-Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal injury.
-Do not overreach. Keep proper footing and balance at all times. This enables better control of the power
tool in unexpected situations.
-Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
3
General Safety Warnings
■ Use and Maintenance of power tool
- Please choose proper power tool according to the fastened object. Proper selected
power tool gets better efficiency.
- Do not use the power tool whenever power switch is faulty. Any power tool with faulty power switch is
dangerous and must be repaired.
- Before making any adjustment, replacing parts or putting away, please unplug the power tool to ensure the
safety and avoid unexpected start-up of power tool.
- Keep the idle power tool away from children, and prevent people who are not familiar with it from
operation. Power tool operated by untrained users is dangerous.
-The maintenance of power tool. Please check for all the possibilities that could affect the operation of
power tool. For example, uncalibrated power tool, movable parts are tied, damaged parts etc.
If any damage is found, repair it before use. Please also note improper repair can lead to an accident
easily.
- Keep the bits clean, and keep the bits with sharp edge, since it can get better control.
- Please follow instruction for the operation of power tool, accessories and bits. Operation failed to follow
the instruction may lead to danger.
4
Read before use
Read before use:
■Please read the following notices before use:
‧Set-up Notice
-The controller should be used indoor and in dry place without the presence of dust and iron grindings.
-The controller should be positioned on a stable surface to avoid falling caused by vibration.
-The controller should be kept away from high voltage sources and noise generating sources to avoid
electromagnetic interference.
-No objects should be placed on the top of the controller. Keep its surrounding clear to allow heat
dissipation.
‧Caution during the operation:
-Please use the power supply with AC circuit which overload relay is included.
-The plug of the power cord is attached with ground pin, which must be connected to the socket equipped
with ground circuit to avoid electric shock.
-The plug of the power cord must be tightly plugged into the socket.
-For plugging and withdrawing the connecting cord between controller and screwdriver, please hold the
plug, do not pull the cable to avoid short circuit of the internal wires.
-It is directional when you plug the connecting cord into the driver and the controller’s socket. You have to
insert it in powerfully after aligning with covex point in the socket; then twist it to fix it on the driver or the
controller. Thus it will reduce the occurrence breakage of connecting cord due to drag. Use the knob to fix
the cable with the controller. Please see the picture below.
-Please do not suddenly switch between forward and reverse when the electric screwdriver is in operation.
-Please use the electric screwdriver with under 80% of the rated maximum torque to avoid inaccurate clutch
escape (The rated maximum torque may vary with the flexibility of the fastened object). If you need to use
over 80% of the rated maximum torque, please use the screwdriver with higher torque.
5
Read before use
‧Safety notice
-If notice smog, smell anything unusual, or hear any unusual noise from the controller, please stop using to
avoid any hazard. Turn off the power immediately and contact your nearest sales agent after no more smog
is found.
-Keep the two-stage switch in OFF position when the controller is not in use. Pull out the plug from the
power source socket when the controller is not in use for a longer period.
-Our controller is for ASA electric screwdriver use only. Do not use it with other tools to avoid any hazard.
6
Declaration of Conformity CE/UKCA/Service
■Declaration of Conformity CE
We (ASA TOOLS Enterprise Corporation) declare under our sole responsibility that the products
controller described under this manual are in conformity with the following Directives/ or standardization
documents: Low Voltage Directive 2014/35/EU and EMC Directive 2014/30/EU.
■Declaration of Conformity UKCA
We (ASA TOOLS ENTERPRISE CORPORATION) The subject equipment under declaration is in
conformity with the UK-GB Regulation(s) below: Statutory Instruments 2016 No. 1091 .The
Electromagnetic Compatibility Regulations 2016
■Service
Have your controller serviced by a qualified repair person using only identical replacement parts. This
will ensure that the safety of the controller is maintained.
■Warranty
We offer one-year free repair service with this product. The warranty is valid for one year from the
original purchasing date. Please note that this warranty policy does not cover the circumstances listed
below and we will charge for repair or labor cost if necessary.
-Consumable parts: relay, Switch or brake circuit.
-Improper use of the electric screwdriver and caused internal discontinuity between two ends (5P-5P/6P-6P)
of the connecting cord.
-The unit was not plugged to designated power source.
-Improper use or power supply is disassembled for maintenance without permission
-Out of the warranty period or the user cannot present the manual.
7
Product information
■Feature
-Universal power source: It is suitable for any power source ranges between 100-240VAC 50/60Hz.
-Stepless control: Output stepless control and constant voltage makes the assembly of light, thin, short, and
small works more efficient and they are key features electron industry pursues after. The smaller the
screw, the higher locking and tightening is required. With this function, it can satisfy the requirements of
high precision and low inertia in both long and short screws fastening.
-Soft start: There is 0-1 sec. soft-start function inside the power supply. The speed of fastening will
gradually change from slow to fast motion during the operation. This lowers the risk of screw shaking
when fastening.
- With output terminal for connecting to External controller for integrated control.
-Digital identified system: When power supply connects to screwdriver and power is On, it
will detect the type of screwdriver automatically.
■Specification
Model
Item
APM-202B APM-302B APM-302C APM-352B
Input Voltage
(VAC) 100~240V 、 50/60Hz
Output Voltage
(VDC) 9-19 V 20-30 V 20-30 V 25-35 V
Soft-start (sec) N/A 0 – 1 sec 0 – 1 sec 0 – 1 sec
Output Voltage
setting Stepless Control
Output Pin 5pin 5pin 6pin 5pin
Internal Signal
Output Switch-on/Brake No-Voltage contact signal (PS series is excluded)
External Signal
Output Switch-on Signal (PS series is excluded)
No. of
Screwdriver/power
supply
1 piece
Power (W) 32.3 W 51W 51W 52.5 W
Applicable Electric
Screwdriver models
ASA-S1000M/A
ASA-S1000M PRO
ASA-S2000M PRO
BS-100
ASA-S1000M/A BS-2000
ASA-S2000M/A BS-3000
ASA-S2500M/A BS-4000
ASA-2000M/S/A BS-4000F
ASA-3000M/S/A BS-6000
ASA-4000M/S/A BS-6500
ASA-7000/PS BS-6800
ASA-8000/PS BS-100F
BS-200 BS-250
BS-300 BS-400
ASA-6000/PS
ASA-6500/PS
ASA-6800/PS
ASA-7500/PS
ASA-2000/S
ASA-3000/S
ASA-4000/S
ASA-4500/S
Dimension (mm) 172X84X46 mm
Weight (g) 380 g
AC cable length
(M) 1.8 M
Safety Standards CB,CE,UL(CUL),ROHS,REACH,KC,FCC,UKCA
Accessories Small screwdriver, 2P/4P socket terminal 1 pieces, and AC cable
8
Operation
■INSTALLATION
DC cable is required to connect between
screwdriver and power supply. Please
kindly note the minimum bend radius(r)
of the cable is 60 mm.
While connecting DC cable
between screwdriver and
power supply (refer to
drawing below), please
align and match the covex
points inside the plug of DC
cable to the plugs on
screwdriver/ power supply,
and insert it properly. Then
rotate and tighten the nut in
clockwise direction.
Turn the power supply ON after
screwdriver is well connected
with it. The LED will flash
Orange 3 times and stay in Green
that is ready for operation.
P.S. While LED is flashing, do
not press the trigger on
screwdriver.
r
LED
■Parts and functions
‧Speed setting
Turn the speed-setting screw through the hole on the side of the power supply with the small screw driver
(standard accessory).
-Turn clockwise 010 on the scale to increase the speed.
-Turn counter-clockwise 100 on the scale to lower down the speed.
APM-Series
9
Operation
‧Soft-start setting (EXCEPT APM-202B)
-Change the two-stage switch on the side of the power supply by hand.
-Switch to SLOW mode 0 1 sec. The speed gradually increases from slow to constant faster speed.
-Switch to FAST mode 0 0 sec. Constant speed without change.
‧Power setting and AC input socket (C13 specification)
-The input voltage of our power supply is ranged between 100-240VAC, 50/60 Hz. Please make sure you
use the correct voltage to avoid any damage to the power supply.
-Connect one side of the cable to the AC power socket and the other side to the AC input socket (C13
specification).
-Change the two-stage switch at the top of the power supply by hand.
On mode, the power supply will be switched on.
Off mode, the power supply will be switched off.
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
