Asante IntraCore 3524 Series Bedienungsanleitung

IntraCore™3524 Series

Gigabit Ethernet Switches

Getting Started Guide

2 Getting Started Guide

Quick Start Guide

Follow these steps to install your IntraCore switch:

1. Open the box and check the contents. See Chapter 1.1 Package

Contents for a complete list of the items included with your IntraCore

switch.

2. Install the switch in an equipment or wall rack, or prepare it for

desktop placement.

3. Connect the power supply.

4. Connect network devices to the switch.

5. Refer to the User’s Manual on the accompanying CD-ROM for

configuration and management capabilities.

For more information on installing the IntraCore 3524, please refer

to Chapter 2 Installation and Setup.

Asanté IntraCore 3524

Table of Contents

Quick Start Guide 2

1. Introduction 5

1.1 Package Contents 6

1.2 LEDs 6

1.3 Front Panel Description 8

2. Installation and Setup 9

2.1 Safety Overview 9

2.2 Recommended Installation Tools 10

2.3 Power Requirements 10

2.4 Environmental Requirements 10

2.5 Cooling and Airflow 11

2.6 Installation Overview 11

2.7 Chassis Installation and Placement 11

2.8 Installing GBIC Interfaces 13

2.9 Installing Optional Hardware Modules 14

2.10 Connecting Power 15

2.11 Connecting to the Network 15

2.12 Using the Stacking Feature 17

Appendix A Troubleshooting 21

Appendix B Safety and Regulatory Compliance 23

Appendix C Features and Specifications 25

Appendix D Serial Port Pin Outs 27

Appendix E Warranty and Support 29

4 Getting Started Guide

Asanté IntraCore 3524

1 Introduction

The IntraCore 3524 Series

Thank you for purchasing the Asanté IntraCore 3524 Series Gigabit

switch. The IntraCore 3524 is a 24-port 10/100 managed switch

with a variety of hardware and software options. Hardware expan-

sion slots (two Type IC35) can accept a wide range of Gigabit and

10/100 Mbps media modules:

•10/100/1000BaseT

•1000BaseX GBIC

•1000BaseSX

•100BaseMMFX

•100BaseSMFX

See the table below for a description of the 3524 series models that

are available.

Model 10/100

Ports

Optional Media

Modules

Description

IC 3524 Base 24 Two IC35 slots

available

Managed 24-port 10/100

switch; base

IC 3524-2T 24 Two 10/100/1000

BaseT ports

Integrated copper Giga-

bit ports

IC 3524-2G 24 Two GBIC ports Integrated Gigabit

Ethernet Interface Con-

verter (GBIC) ports

Table 1-1—3524 Models

6 Getting Started Guide

The system can operate as a stand-alone network or be used in

combination with other IntraCore series switches in the backbone.

1.1 Package Contents

The following items are included in your package:

•Switch

•AC power cord

•Rack mount brackets with screws

•Rubber feet

•Reference Guide

•User’s Manual (on CD-ROM)

•Getting Started Guide (this document)

•IntraCore 3524 CD-ROM

Contact your dealer immediately if any of these items are missing.

1.2 LEDs

The system’s LED display

allows you to monitor the

status of your switch. See

Tables 1-2 and 1-3 below

for a complete LED description.

Asanté IntraCore 3524

Port # LED Color Description

25,26 Gigabit

(speed)

Solid Green

Off

A valid 1000Mbps link has

been established

No link has been estab-

lished, or link is at

10/100Mbps rate

25,26 10/100 Link Solid Green

Solid Amber

Off

A valid 100Mbps link has

been established

A valid 10Mbps link has

been established

No 10/100 link has been

established

25,26 Duplex Solid Green

Solid Amber

Full Duplex

Half Duplex

Table 1-3—Ports 25 & 26 have 3 LEDs each

Port # LED Color Description

N/A Power/

System

Green

Off

Power is on

Power is off

1-24

(10/100)

10/100 Link Solid Green

Solid Amber

Off

A valid 100 Mbps link has

been established

A valid 10Mbps has been

established

No link has been estab-

lished

1-24

(10/100)

Duplex Solid Green

Solid Amber

Full Duplex

Half Duplex

Table 1-2—Ports 1-24 have two LEDs each

8 Getting Started Guide

1.3 Front Panel Description

From left to right, the front panel contains the following: Power and

port LEDs; 24 10/100 ports; 2 optional module slots; and a console

port.

The switch is field upgradeable for use with 1000BaseSX,

1000BaseX GBIC or 10/100/1000BaseT modules.

Optional modules for the IC 3524

Front Panel IC 3524 Base

Asanté IntraCore 3524

2 Installation and Setup

This chapter explains how to install and connect the switch to

your network. To configure the switch for management, refer to

the User’s Manual on the CD-ROM.

The following guidelines will help you prepare to install the

switch in such a way that it has the proper power supply and

environment.

2.1 Safety Overview

The following information provides safety guidelines to ensure your

safety and to protect the switch from damage.

Note: Be aware, however, that this information is intended as a

guideline, and may not include every possible hazard to which you

may be exposed. Use caution when installing this switch.

•Only trained and qualified personnel should be allowed to in-

stall or replace this equipment.

•Always use caution when lifting heavy equipment

•Keep the chassis clean

•Keep tools and chassis components off the floor and away from

foot traffic

•Avoid wearing rings or chains (or other jewelry) that could get

caught in the chassis. Metal objects can heat up and cause

serious injury to persons and damage to the equipment. Avoid

wearing loose clothing, i.e. ties or sleeves

When working with electricity, follow these guidelines:

•Before accessing the interior of the chassis, locate

the emergency power-off switch for the room you are in

•Disconnect all external cables before installing or removing a

chassis

•Do not work alone when working with electricity

•Always check that the power has been disconnected from the

circuit

10 Getting Started Guide

•Do not tamper with the internal components of your switch.

This could void your warranty

•Examine your work area for potential hazards (I.e. wet floors,

ungrounded cables, etc.) and eliminate them before installing

your switch

For more safety information, please refer to the User’s Manual.

2.2 Recommended Installation Tools

You will need the following tools and equip-

ment (not included) to install the switch:

•Number 1 Phillips screwdriver

•Number 2 Phillips screwdriver

•3/16-inch flat-blade screwdriver

•Antistatic mat or foam

•An ESD grounding strap

2.3 Power Requirements

The electrical outlet should be located near the switch and be easily

accessible. It must also be properly grounded.

Make sure the power source adheres to the following guidelines:

•Power: Auto Switching 110/240 VAC

•Frequency range: 50/60 Hz

•Maximum input AC Current: 1.0A at 115 VAC full load

2.4 Environmental Requirements

The switch must be installed in a clean, dry, dust-free area

with adequate air circulation to maintain the following environ-

mental limits:

•Operating Temperature: 0° to 40° C (32° to 104° F)

•Storage Temperature: -20° to 70° C (-4° to 158° F)

•Relative Humidity: 10% to 90% relative humidity

•Storage Relative Humidity: 10% to 95% relative humidity

Andere Handbücher für IntraCore 3524 Series

Inhaltsverzeichnis

Andere Asante Schalten Handbücher

Asante

Asante FRIENDLYNET FS4116R Bedienungsanleitung

Asante

Asante FriendlyNET FX4000 Bedienungsanleitung

Asante

Asante IntraCore IC3624 Bedienungsanleitung

Asante

Asante IntraCore 35516 Series Bedienungsanleitung

Asante

Asante FriendlyNET GX5-2400W Bedienungsanleitung

Asante

Asante FriendlyNET 2024P Bedienungsanleitung

Asante

Asante IntraCore 3548-2GT Series Bedienungsanleitung

Asante

Asante FriendlyNET GXS-424W Bedienungsanleitung

Asante

Asante FriendlyNET Wireless USB Adapter Bedienungsanleitung

Asante

Asante Universal Serial Bus Hub USB Hub-4 Bedienungsanleitung

Asante

Asante IntraCore 36000 Series Bedienungsanleitung

Asante

Asante IntraCore GBIC 1000LX Handbuch

Asante

Asante FriendlyNET FM2008 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

Asante

Asante 3500 Bedienungsanleitung

Asante

Asante FriendlyNET FM2008 Bedienungsanleitung

Asante

Asante FriendlyNET GX5-2400W Bedienungsanleitung

Asante

Asante 10Base2 Mini MAU Bedienungsanleitung

Asante

Asante 3500 Bedienungsanleitung

Asante

Asante FM2008/2009 Bedienungsanleitung

Asante

Asante IntraCore IC3648 Bedienungsanleitung

Asante

Asante IntraSwitch 5324 Bedienungsanleitung

Asante

Asante IntraCore 35516 Series Bedienungsanleitung

Asante

Asante FriendlyNet FH205P Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung