ASE VS58D4 Bedienungsanleitung

Radio transmitter kit of TV and CCTV signal - DIRECTIONAL.

Working with 4 cameras, range up to 1000 m

4 x transmitter T58M

antenna AP58S

receiver 4R58C

Installation :

Unpack the set. Open the lid with cableways . Prepare concentric cable to

video transmission (RG-59). Use heat-shrinkable film (as on the picture

below). Also prepare mains cable (LIYY 2 without audio signal or LIYY5x0.75

with audio signal.

Channel selection:

Change the setting of the channel switch only

when the power is off.

Use the DIP switches to select the channel as

shown in the table.

The settings must be the same in both the

transmitter and the transmission path of receiver

All transmission path must be configured for different

channels (pre-set channels 1, 3, 5, 7).

(reading the channel number is only at powering)

Transmitters: thread the cables trough the proper cable bushing and connect to the clamp bar

according to the description below :

The package includes:

1. T58S transmitter (integrated with directional antenna) .............. 4 pcs

2. 4R58C - receiver (4 transmitters in continuous operation) ............ 1 pcs

3. AC adapter for the receiver ...................................................... 1 pcs

4 receiving antenna AP58S (directional, flat panel) ........................ 1 pcs

5. mounting bracket .................................................................... 5 pcs

6. instruction

Technical specifications:

amount of transmission paths ..................................................................... 4

range of frequency .................................................................................... 5740 - 5860MHz

amount of channel (frequency set independently for each transmission path) ... 7

supply: transmiterrs .................................................................................. 12V / 0,2A

supply: reciver (adapter included) ............................................................... 6V / 1A

transmitters: RF output power ........................ < 25mW (

video signal: parameters of input / output ..... 1V ; 75om

type video signal .......................................... PAL / NTSC

audio signal: parameters of input / output ....... 0.7V ; 1kom

modulation ................................................. FM

beamwidth (horizontal and wertical).................20 deg

polarization of antennas ................................. horizon

operating temp. range...................................... -40 +70 C deg

class of hermetic (only transmitters) ................. IP65

dimension of pack .......................................... 250x 170 x 360 mm

weight with packaging...................................... 4 kg

RF power compatible with CE)

1. video ground (RG-59 metallic shield)

2. video signal (RG-59 centre core)

3. audio L

4. audio R

5. - supply ground

6. + supply 12V

LED. supply lamp signal

A. adjustment of the camera output

Screw tight the screws on the cable bushings.

Using connection clips attach the devices to masts or extensions.

Connect the receiver to the panel antenna by coaxial cable (recommended type: TRI-LAN400).

Required to connect the connectors: N (antenna) and SMARP (receiver).

Antennas should be placed at highest possible place and .

Since the devises work as directional antennas it is important that they are facing each other.

The holder can be adjusted +/- a degree which helps to install the devises properly.

After finishing the installations the cables must be attached with the hose damps to the

mast on extension closely to the devises.

For transmitters use brand-good power supplies (output DC 12V, current 0,5A or more).

After turning on the power supply the signal transmissions starts on the channel chosen.

Transmitter is equipped with potentiometer, which allows to adjust the vision output to the camera

parameters. If these are such necessity (insufficient contrast) you can regulate the parameters.

greater than 2,5m above the ground

office address:

ASE

Anielów 22

08-460 Sobolew

POLAND

- function relays

- automotive electronic circuits

- telecommunication systems

- custom orders

e-mail: [email protected]

tel.: +48 720 239 596

Design and

production:

manual / instrukcja www.ase.hoste.pl

office address:

ASE

POLAND

Anielów 22

08-460 Sobolew

- function relays

- automotive electronic circuits

- telecommunication systems

- custom orders

e-mail: [email protected]

tel.: +48 720 239 596

Design and

production:

manual / instrukcja www.ase.hoste.pl

VG VC AL AR VG VC AL AR VG VC AL AR VG VC AL AR -+

RECIVER 1 RECIVER 2 RECIVER 3 RECIVER 4 6V

TERMINAL

SUPPLY

AUDIO4

VIDEO4

AUDIO3

VIDEO3

AUDIO2

VIDEO2

AUDIO1

VIDEO1

1 2 3

DIP1

ON ON ON

DIP4

1 2 3 1 2 3 1 2 3

DIP2 DIP3

FUSE 2A

FUSE : 2A

CCTV AV RECIVER model 4R58C ASE www.ase.hoste.pl

ASE

1 2 3 4

5 6 7 8

10 10 11 10 12 10 13

receiver 4R58C - side view (enclosure closed)

receiver 4R58C - view from the top (enclosure opened)

1 2 3

> audio L

> audio R

> supply ground

> supply 12V

> video ground

(RG-59 metallic shield)

> video signal

(RG-59 centre core)

> signal transmission >

video

supply, audio

CCTV camera

receiving antenna

AP58S

transmitter 4

VS58D4 wiring diagram

CCTV monitors

seal

1. video ground (RG-59 metallic shield)

2. video signal (RG-59 centre core)

3. audio L

4. audio R

5. - supply ground

6. + supply 12V

LED. supply lamp signal

A. adjustment of the camera output

1 2 3

1 2 3 4 5 6

LED

cable terminals of transmitters :

video

supply, audio

video

supply, audio

video

supply, audio

transmitter 1

transmitter 2

transmitter 3

video signal

receiver 4R58C

signal with

the directional antenna

audio signal

channel switch position

1. signal connector (audio, video) - receiver path I

2. signal connector (audio, video) - receiver path II

3. signal connector (audio, video) - receiver path III

4. signal connector (audio, video) - receiver path IV

5. dip-switch sets the transmission frequency (1 of 7 channels), to receiver path I

6. dip-switch sets the transmission frequency (1 of 7 channels), to receiver path II

7. dip-switch sets the transmission frequency (1 of 7 channels), to receiver path III

8. dip-switch sets the transmission frequency (1 of 7 channels), to receiver path IV

9. power fuse (slow-blow 2A)

10. glands of signal cables

11. RP SMA antenna connector

12. AC power adapter (6V / 1A)

13. LED - the power

office address:

ASE

Anielów 22

08-460 Sobolew

POLAND

- function relays

- automotive electronic circuits

- telecommunication systems

- custom orders

e-mail: [email protected]

tel.: +48 720 239 596

Design and

production:

manual / instrukcja www.ase.hoste.pl

Zestaw urz¹dzeñ do radiowej transmisji sygna³u TV i CCTV

dla 4 kamer - zasiêg 1000m - KIERUNKOWY

1. T58S - 4 x nadajnik zintegrowany z anten¹ .................................... 4szt.

2. 4R58C - odbiornik (praca z 4 nadajnikami w trybie ci¹g³ym) ............ 1 szt

3 zasilacz odbiornika ............................................................................. 1 szt..

4. antena odbiorcza AP58S .................................................................... 1 szt.

5. uchwyt monta¿owy (obejma) .............................................................. 5 szt.

6. instrukcja

Opakowanie zawiera:

Dane Techniczne

iloœæ torów transmisji ........................................................................................ 4

kana³y (czêstotliwoœæ niezale¿nie ustawiana dla ka¿dego toru transmisji) ..... 7

zasilanie: nadajnik ........................................................................................... 0,2A (12V)

zasilanie: odbiornik (zasilaccz w komplecie) .................................................. 1A (6V)

moc promieniowania ( ...................... < 25mW

wizja : parametry wejœcia / wyjœcia ................... 1V ; 75om

typ przesy³anego sygna³u .................................. PAL / NTSC

fonia: parametry wejœcia / wyjœcia .................... 0.7V ; 1kom

modulacja ......................................................... FM

k¹t wi¹zki g³ównej anten TX i RX ...................... 20 st.

polaryzacja anten.............. ............................... pozioma

zakres temp. pracy ............................................... -40 +70

klasa szczelnoœci nadajników ............................... IP65

wymiary opakowania .. .................................... ...

waga z opakowaniem ......... 4 kg

zakres czêstotliwoœci pracy ................................................................................ 5740- 5860MHz

nadajnik) (moc nadawcza zgodna z CE)

250x 170 x 360 mm

Instalacja:

Rozpakowaæ urz¹dzenia, odkrêciæ pokrywy z przepustami kablowymi .

Przygotowaæ kabel koncentryczny do przesy³u wizji RG-59 (u¿yæ koszulki

termo-kurczliwej, tak jak na rys. poni¿ej), oraz zasilania (LIYY 2x1 bez sygna³u audio,

lub LIYY5x0.75 je¿eli sygna³ audio bêdzie wyprowadzany).

Ustawiæ w odbiorniku i nadajnikach,

prze³¹cznikiem typu „DIP switch"

kana³y pracy (1 z 7 dostêpnych) zgodnie z tabel¹:

W nadajnikach ustawienia musz¹ byæ

takie same jak we wspó³pracuj¹cych z nimi torach

odbiorczych (fabrycznie ustawiono kana³y 1,3,5,7) .

Zainstalowane w pobli¿u zestawy

(bêd¹ce w polu w³asnego zasiêgu radiowego)

musz¹ mieæ ustawione ró¿ne kana³y.

Ustawianie kana³ów nale¿y wykonywaæ tylko przy

wy³¹czonym zasilaniu.

(odczyt numeru nastêpuje tylko podczas w³¹czania zasilania)

W nadajnikach przewlec kable poprzez odpowiednie dla nich przepusty i pod³¹czyæ do listwy

zaciskowej zgodnie z opisem :

1. masa wizji (koncentryk ekran)

2. sygna³ wizji (koncentryk centralny)

3. fonia L

4. fonia P

5. - zasilania (GND)

6. + zasilania 12V

LED. sygnalizacja zasilania

A. dopasowanie wyjœcia kamery

Przykrêciæ pokrywy, dokrêciæ przepusty kablowe.

Pod³¹czyæ odbiornik z anten¹ panelow¹ kablem koncentryczny (zalecany typ :TRI-LAN400).

Do pod³¹czenia wymagane s¹ z³¹cza : N (antena) i SMARP (odbiornik).

Za pomoc¹ do³¹czonych obejm, umieœciæ urz¹dzenia na wczeœniej przygotowanych masztach lub wysiêgnikach.

Anteny powinny byæ ustawione mo¿liwie najwy¿ej i . Poniewa¿ maj¹

charakterystykê kierunkow¹ , wa¿ne ¿eby by³y doœæ precyzyjnie ustawione w osi „twarzami" do siebie.

W ustawieniu pomaga mo¿liwoœæ regulacji k¹ta na uchwycie (+/- 20 st.) .

Po zakoñczeniu monta¿u, do masztu w pobli¿u urz¹dzeñ.

Do zasilania nadajników stosowaæ zasilaczy (lub wiêkszych) transformatorowych lub

markowych impulsowych. Po w³¹czeniu zasilania, nastêpuje transmisja sygna³ów z nadajnika do odbiornika,

na wybranym wczeœniej kanale .

Nadajnik jest wyposa¿ony w potencjometr, umo¿liwiaj¹cy dopasowanie wejœcia wizji do parametrów wyjœcia

kamery . Je¿eli zachodzi taka potrzeba (niedostateczny kontrast), nale¿y wykonaæ regulacjê.

nie mniej ni¿ 2,5m nad ziemi¹

kable musz¹ byæ przypiête opaskami

stabilizowanych 12V 0,5A

4 x transmitter T58M

antenna AP58S

receiver 4R58C

office address:

ASE

Anielów 22

08-460 Sobolew

POLAND

- function relays

- automotive electronic circuits

- telecommunication systems

- custom orders

e-mail: [email protected]

tel.: +48 720 239 596

Design and

production:

manual / instrukcja www.ase.hoste.pl

office address:

ASE

POLAND

Anielów 22

08-460 Sobolew

- function relays

- automotive electronic circuits

- telecommunication systems

- custom orders

e-mail: [email protected]

tel.: +48 720 239 596

Design and

production:

manual / instrukcja www.ase.hoste.pl

odbiornik 4R58C - widok z boku (pokrywa zamkniêta)

odbiornik 4R58C - wiook po otwarciu pokrywy

DECLARATION OF CONFORMITY

ASE

Anielów 22

08-460 Sobolew

Poland

We herewith declare that the following designated product: model VS58D4 (5.8GHz Wireless Audio/Video Sender)

< 25mW

5740 – 5860 MHz

parameters

transmitter radiated power

frequency of work

Complies with the requirements set in the Council Directive on the Approximation of the Laws of the

Member States relating to:

the European Parliament and of the Council of 9 March

1999 on radio equipment and telecommunications terminal equipment and the mutual recognition

of their conformity

the European Parliament and of the Council of 15 December 2004 on the

approximation of the laws of the Member States relating to electromagnetic compatibility

the European Parliament and of the Council of 27 January 2003 on the

restriction of the use of certain hazardous substances in electrical and electronic equipment

the European Parliament and of the Council of 12 December 2006 on the

harmonization of the laws of Member States relating to electrical equipment designed for use within

certain voltage limits

The symbol confirms that this product conforms to the above named standards and regulations.

NBnr: 0536

Directive 1999/5/EC

Directive 2004/108/EC

Directive 2002/95/EC

Directive 2006/95/EC

(Switching Power Supplies).

The following standards were consulted to assess conformity:

Radio: EN 300440-2: 2008

EN 300220-2: 2007

EMC: EN 301 489-1: 2005

EN 301 489-3: 2002

Safety: EN 60 065: 2002 / A1: 2006

This product is suitable for use in all EU countries.

Note: Although this product does not contain any harmful materials,we suggest

you return the product to the dealer or directly to the producer after use.

VG VC AL AR VG VC AL AR VG VC AL AR VG VC AL AR -+

RECIVER 1 RECIVER 2 RECIVER 3 RECIVER 4 6V

TERMINAL

SUPPLY

AUDIO4

VIDEO4

AUDIO3

VIDEO3

AUDIO2

VIDEO2

AUDIO1

VIDEO1

1 2 3

DIP1

ON ON ON

DIP4

1 2 3 1 2 3 1 2 3

DIP2 DIP3

FUSE 2A

FUSE : 2A

CCTV AV RECIVER model 4R58C ASE www.ase.hoste.pl

ASE

1 2 3 4

5 6 7 8

10 10 11 10 12 10 13

1. z³¹cze sygna³owe (audio, wizja) - tor odbiorczy I

2. z³¹cze sygna³owe (audio, wizja) - tor odbiorczy II

3. z³¹cze sygna³owe (audio, wizja) - tor odbiorczy III

4. z³¹cze sygna³owe (audio, wizja) - tor odbiorczy IV

5. dip-switch ustawiaj¹cy czêstotliwoœæ transmisji (1 z 7 kana³ów), dla toru odbiorczego I

6. dip-switch ustawiaj¹cy czêstotliwoœæ transmisji (1 z 7 kana³ów), dla toru odbiorczego II

7. dip-switch ustawiaj¹cy czêstotliwoœæ transmisji (1 z 7 kana³ów), dla toru odbiorczego III

8. dip-switch ustawiaj¹cy czêstotliwoœæ transmisji (1 z 7 kana³ów), dla toru odbiorczego IV

9. bezpiecznik zasilania (zw³oczny 2A)

10. przepusty kabli sygna³owych

11. z³¹cze antenowe SMA RP

12. gniazdo zasilania (6V / 1A)

13. LED - kontrolka zasilania

Date: 30.10. 2014

Technical Product Manager : R. Siwiak

office address:

ASE

Anielów 22

08-460 Sobolew

POLAND

- function relays

- automotive electronic circuits

- telecommunication systems

- custom orders

e-mail: [email protected]

tel.: +48 720 239 596

Design and

production:

manual / instrukcja www.ase.hoste.pl

office address:

ASE

POLAND

Anielów 22

08-460 Sobolew

- function relays

- automotive electronic circuits

- telecommunication systems

- custom orders

e-mail: [email protected]

tel.: +48 720 239 596

Design and

production:

manual / instrukcja www.ase.hoste.pl

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung