Ashcroft GC52 Bedienungsanleitung

Product Information Page

All specifications are subject to change without notice.

All sales subject to standard terms and conditions.

ashcroft.com

info@ ashcroft.com

1.800.328.8258

Rev. A 02/17, Page 1 of 8

PIP #: TR-PI-102

Applicable to:

GC52

PROGRAMMING USER DEFINED FLOW RATE UNITS ON THE GC52

DIFFERENCIALPRESSURE TRANSMITTER

The GC52 differential pressure transmitter is compact and flexible

instrument often used in flow measurements and volume applications. It

can be easily programmed with user defined units to display flow rate in

Gallons Per Minute (GPM) and volume in gallons.

Figure 1 –GC52 Differential Pressure Transducer

Water Flow Rate and Volume Application:

This example demonstrates the use of GC52 differential pressure transmitter to measure and control

flow rate in GPM. Also, to switch from flow rate reading to volume, automatic or manual. Although, the

GC52 differential pressure transmitter can be purchase with several ranges, for this application a

transmitter with 0 to 40 IWC pressure range has been selected. As well, an orifice plate with 2.40” bore,

an eight-inch line diameter pipe and a variable frequency water pump. The transmitter shall provide the

analog output to the variable frequency water pump. The variable frequency water pump uses the 4-

20mA input to control the amount of energy sent to the pump to slow down or speed up the pump to

maintain a constant flow of 65 GPM.

Product Information Page

All specifications are subject to change without notice.

All sales subject to standard terms and conditions.

ashcroft.com

info@ ashcroft.com

1.800.328.8258

Rev. A 02/17, Page 2 of 8

Figure 2 - GC52 Flow Rate Diagram Example Figure 3 - GC52 Installation Example

Installation:

Remove the lid from the transmitter by turning it counter clockwise to expose electrical terminal block.

Wire transmitter per manual instructions, and see diagram below for reference.

Figure 4 - GC52 Wiring Diagram

Product Information Page

All specifications are subject to change without notice.

All sales subject to standard terms and conditions.

ashcroft.com

info@ ashcroft.com

1.800.328.8258

Rev. A 02/17, Page 3 of 8

Principles of Operation and Program Instructions:

Flow rate is calculated by using Bernoulli’s equation below by measuring the differential pressure across

an orifice plate. The GC52 will be using the orifice plate manufacturer’s data of maximum flow rate with

corresponding differential pressure drop.

𝑄= 𝐾√∆𝑃

𝜌

𝐾= 𝑐𝑜𝑒𝑓𝑓𝑖𝑐𝑖𝑒𝑛𝑡

∆𝑃= 𝐷𝑖𝑓𝑓𝑒𝑟𝑒𝑛𝑡𝑎𝑖𝑙 𝑃𝑟𝑒𝑠𝑠𝑢𝑟𝑒

𝜌= 𝐷𝑒𝑛𝑠𝑖𝑡𝑦

𝑄= 𝐹𝑙𝑜𝑤 𝑟𝑎𝑡𝑒

Manufacturer orifice plate specifications:

𝐿𝑖𝑛𝑒 𝑆𝑖𝑧𝑒 = 8” 𝑑𝑖𝑎𝑚𝑒𝑡𝑒𝑟

𝐵𝑜𝑟𝑒 = 2.4” 𝑏𝑜𝑟𝑒

𝑀𝑎𝑥𝑖𝑚𝑢𝑚 𝐹𝑙𝑜𝑤 = 88 𝐺𝑃𝑀 @ 20 𝐼 𝑊𝐶

GC52 Differential Pressure Transducer Flow and integrated Volume Program Guidelines:

Below is an Illustration to program the transmitter in GPM and integrated volume in gallons as the

arbitrary units. Proceed to scale down the transducer range from 40 IWC to 20 IWC. That, is the

maximum differential pressure equivalent to 88 GPM of water (20 mA). Follow the steps below to

rescale and program the transmitter from 0 to 20 IWC of water equivalent to the arbitrary units of 0 to

88 GPM.

Remove Access Cover to Expose MODE, UP and DOWN Buttons

Press and hold M button for more than three seconds to get into program

mode.

Press UP or Down arrow to make changes.

Press and release M button to select changes and to walk through the menu.

Continue to step-1 after power-on message.

Press and hold M button anytime for more than three seconds to return to

measuring mode.

Product Information Page

All specifications are subject to change without notice.

All sales subject to standard terms and conditions.

ashcroft.com

info@ ashcroft.com

1.800.328.8258

Rev. A 02/17, Page 4 of 8

F0To enter filter selection (selections of 0,2,4,8, and 16 times).

The filter function is used when pressure fluctuates to improve

analog output and difficult to read display.

Select the factory default filter F0. Since pressure fluctuation is not

expected.

Press and release M button to select and move to the next step.

Step

nrot To enter configuration mode. There are three pressure modes,

linear, non-linear, and square root function.

Select square root function to convert pressure into flow rate and to

use arbitrary units.

Press UP or Down arrow to display “n rot”.

Press and release M button to select and move to the next step.

Step

P 20.0 To enter the maximum differential pressure corresponding

to the maximum flow rate (88 GPM).

This is the orifice plate specification value.

Press Up or Down arrow until 20.0 is displayed. That, is the

maximum differential pressure corresponding to 88 GPM of water.

Press and release M button to select and move to the next step.

Step

d1To select the decimal point position. There are four decimal

point selections (0,1, 2, and 3 digits).

Press Up or Down arrow until 1 is display. For this application one

digit after decimal point shall be used.

Press and release M button to select and move to the next step.

Step

_ _ _ _

d 88.0 To enter the maximum arbitrary units 88 GPM of water

corresponding to differential pressure of 20 IWC.

Press Up or Down arrow until 88.0 is selected. That, is the 88 GPM of

water corresponding to 20 IWC.

Press and release M button to select and move to the next step.

Product Information Page

All specifications are subject to change without notice.

All sales subject to standard terms and conditions.

ashcroft.com

info@ ashcroft.com

1.800.328.8258

Rev. A 02/17, Page 5 of 8

Step

L0.0 To enter low-cut to flow rate. It forces display to zero and

analog output to 4 mA.

Low-cut shall not be used on this application, constant flow rate

shall be maintained.

Press Up or Down arrow until 0.0 is selected.

Press and release M button to select and move to the next step.

Step

A 0.0 To enter analog output zero reference corresponding to 4

mA.

The operational range is from 0 to 88 GPM of water. Therefore,

select 0% FS or 4mA analog output.

Press Up or Down arrow until 0.0 is displayed. That, is the analog

output at 0% FS (4mA at 0 GPM of water).

Press and release M button to select and move to the next step

Step

_ _ _ _

A 100.0 To enter span analog output reference corresponding to 20

mA.

The operational range is from 0 to 88 GPM of water. Therefore,

100% full span is selected as the span or 20 mA analog output.

Press UP or Down arrow until 100.0 is displayed. That, is the analog

output at 100% FS (20mA at 88 GPM).

Press and release M button to select and move to the next step.

Step

Unin To enter time factor. When flow rate is GPM, minutes shall

be selected as the same time factor.

Press UP or Down arrow until “n in” is displayed. That, is the time

factor corresponding to minutes.

Press and release M button to select and move to the next step.

Step

U _ _ 1 To enter Flow rate volume factor. When flow rate is GPM, 1

shall be selected to match flow factor units of gallons X1.

Selectable options 1,10, 100 and 1000.

1 shall be selected since the arbitrary units are in gallons.

Press UP or Down arrow until “1” is displayed. That, is the unit factor

corresponding to gallons.

Press and release M button to select and move to the next step.

Product Information Page

All specifications are subject to change without notice.

All sales subject to standard terms and conditions.

ashcroft.com

info@ ashcroft.com

1.800.328.8258

Rev. A 02/17, Page 6 of 8

Step

Sbt To enter switch mode of momentary flow rate and integrated

volume. There is manual mode (bt) or automatic mode (ti).

For this application manual switch mode shall be selected.

It only displays integrated volume when cover is removed and M

button is pressed. Otherwise it only displays flow rate.

Automatic setting time is selectable from 1 to 10 seconds cycle.

Press UP or Down arrow until “bt” is displayed.

Press and release M button to select and move to the next step.

Step

C 0.0 Loop check mode allows program and analog output

verification with the transmitter pressurized or non-pressurized. It

simulates the process and allows for troubleshooting.

Press Up or Down arrow to change within transmitter range (0 to 88

GPM of water).

Press and release M button to return to the begin of program

After verification press and hold M button for more three seconds to

return to measuring mode.

Function Verification:

The GC52 loop-check allows to verify program and analog output with the transmitter pressurized or

non-pressurized.

Once Step-11 is reached, the unit is in Loop-

check mode. The system can be verified by

increasing or decreasing the flow rate value (0 to

88 GPM of water).

Use the Up or down arrow and observe the

display segments get brighter as the flow rate

value increases. That, is an indication that the

analog output and wiring are reacting properly.

Product Information Page

All specifications are subject to change without notice.

All sales subject to standard terms and conditions.

ashcroft.com

info@ ashcroft.com

1.800.328.8258

Rev. A 02/17, Page 7 of 8

Analog output terminal check:

When the front cover is removed, the analog output check terminals CH+ and CH–are visible at the

upper part of the display. The analog output can be checked during measurement mode or loop check

(see figure 4 below for reference).

Figure 4 - Analog Output Verification

C 44.0

Product Information Page

All specifications are subject to change without notice.

All sales subject to standard terms and conditions.

ashcroft.com

info@ ashcroft.com

1.800.328.8258

Rev. A 02/17, Page 8 of 8

Analog output check:

Similarly, analog output can be verified by placing an amp-meter in series with the transmitter output

and power supply (see manual wiring instructions for reference). As well, during measurement mode or

loop check (see results below for reference).

Connect amp meter per manual

instructions or figure above.

Press the Down arrow until 0.0 GPM is

displayed or apply 0 IWC.

Verify amp meter reading (4.00 mA).

0.0 GPM of water corresponds to 0% FS (4

mA at 0.0 GPM of water).

Press the Up or Down arrow until 44.0 GPM

is displayed or apply 10 IWC.

Verify amp meter reading (12.00 mA).

44.0 GPM of water corresponds to 50% FS

(12 mA at 44.0 GPM of water).

Press the Up arrow until 88.0 GPM is

displayed or apply 20.0 IWC.

Verify amp meter reading (20.0 mA).

88.0 GPM of water corresponds to 100% FS

(20 mA at 88.0 GPM of water).

Andere Handbücher für GC52

Inhaltsverzeichnis

Andere Ashcroft Sender Handbücher

Ashcroft

Ashcroft GXLdp Bedienungsanleitung

Ashcroft

Ashcroft km46 Bedienungsanleitung

Ashcroft

Ashcroft KX1 Bedienungsanleitung

Ashcroft

Ashcroft km46 Bedienungsanleitung

Ashcroft

Ashcroft KM41 Bedienungsanleitung

Ashcroft

Ashcroft ZT11 Bedienungsanleitung

Ashcroft

Ashcroft G2 Bedienungsanleitung

Ashcroft

Ashcroft GC51 Bedienungsanleitung

Ashcroft

Ashcroft km11 Bedienungsanleitung

Ashcroft

Ashcroft XLDP1 Bedienungsanleitung

Ashcroft

Ashcroft ZX11 Series Bedienungsanleitung

Ashcroft

Ashcroft A4 Bedienungsanleitung

Ashcroft

Ashcroft ZT12 Bedienungsanleitung

Ashcroft

Ashcroft GC52 Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung