Asko T700 Series Bedienungsanleitung

Asko-App l i ancesAsko - App l i ances

BUILT TO LAST LONGER

ASKO

SERVICE

ACADEMY

Service Manual

for the 700

Series of

Tum le Dryers

INTRODUCTION

You have in your hand the ASKO Service Manual for the new generation of tumble

driers, that are friendly to the environment in both their manufacture and their use.

This new generation of tumble driers has been designed for ease of servicing. By this

we mean that it's a simple job, for example, to replace a damaged side panel.That's

why we've changed the design from a one-piece shell to a split shell.

To secure parts and wiring, we have replaced many of the screws by plastic snap

fasteners, and certain parts have integrated ribbon cabling, all for simplifying service.

We have also integrated service aids, such as hooks to hang parts on, so that you

can use both hands for installation.

Presentation of the different models:

T700 - is a thermostatically-controlled tumble dryer with air extraction

T720 - is a timer-controlled tumble dryer with a condenser

T760 - is a sensor-controlled electronic tumble dryer with air extraction

T780 - is a sensor-controlled electronic tumble dryer with a condenser

The T760 and T780 are equipped with internal lighting. They have a humidity

sensor that can tell when the clothes are dry.

You can choose from a total of eleven different languages on the display, the

number and choice of languages depend on the market.

Servicing the tumble driers has to be easy, and just as it is important for us that the

customer shall be satisfied with our simple, able and durable 700 series, so we also

want to give you, the service engineer, the conditions to permit you to work effi-

ciently and satisfactorily.

We hope that this Service Manual will be a positive tool in your daily work, and

you are welcome, if you have any questions concerning servicing ASKO products, to

SAFETY REGULATIONS

GENERAL

• The electrical and plumbing installations shall

be carried out by a qualified electrician and

plumber respectively.

SERVICE

WARNING

Always switch off the main electrical power supply

when dismantling and assembling the washing

machine.

• Always use an earthed EMC wristband when

working with electrical components, such as

panel printed circuit boards and electronic

control units.

T720: TRANSPORT/WINTER STORAGE

If the tumble drier is to be transported, or stored

for the winter in unheated premises, ensure that

the condensation water tank has no water in it.

T780: TRANSPORT/WINTER STORAGE

If the tumble drier is to be transported, or stored

for the winter in unheated premises, ensure that

the condensation water tank has no water in it.

DISPOSAL

When the tumble drier comes to end of its useful

life and is to be scrapped, it must be immediately

rendered unusable.

Contact your local authority to find out how the

tumble drier should be scrapped and recycled pro-

perly.

The tumble drier is manufactured and labelled

for recycling.

SAFETY REGULATIONS

SPECIFICATIONS

PRINCIPAL DIMENSIONS

Height: 850 mm

Width: 595 mm

Depth: 585 mm

Weight:

T700 39 kg

T720 47 kg

T760 39 kg

T780 47 kg

VOLUME/CAPACITY

Drum volume 111 litres

Drying capacity - EU: 5.0 kg

Drying capacity - AU: 5.0 kg

Speed: 52 rpm

ELECTRICAL CONNECTION ALTERNATIVES

Power consumption: See type label

Heating element power: See type label

Drying drum material:

Stainless steel.

Outer casing material:

Powder-painted and hot galvanised steel plate

or stainless steel.

Installation:

Tower, free-standing or built-in.

Drain

T720/780: 2.0 m rubber hose

Air extraction hose

T700/760: 3.0 m PVC

Lamp

T760/780: 10 W, E14 socket

SPECIFICATIONS

THE DRYING PROCESS

T700:

Air at room temperature is heated by the heating

element and drawn into the drum, where it ex-

tracts the dampness from the clothes. The ridges

in the drum prevent the clothes from sticking to

each other.

Air passes through the fluff filter in the front door,

through the exhaust system and out.

T760:

Air at room temperature is heated by the heating

element and drawn into the drum, where it ex-

tracts the dampness from the clothes. The ridges

in the drum prevent the clothes from sticking to

each other.

Air passes through the fluff filter in the front door,

through the exhaust system and out.

On the way through the air extraction system the

air passes a humidity sensor. The sensor measures

the amount of humidity in the clothes. If you are

using an automatic program, the sensor indicates

when the clothes are dry.

THE DRYING PROCESS

T720/780:

The condensing tumble drier has two circulation

systems: one for drying air and one for cooling

air. The black arrows show the warm drying air,

and the white arrows the cooling air at room tem-

perature.The ridges in the drum prevent the clo-

thes from sticking to each other. On the way th-

rough the air extraction system the air passes a

humidity sensor. The sensor measures the amount

of humidity in the clothes. If you are using an

automatic program, the sensor indicates when the

clothes are dry.

AIR DRIER

Air at room temperature is heated by the heating

element and passes through the drum, where it

blows through the clothes and extracts the damp-

ness from them.

The air is filtered through the fluff filter in the

front door, goes down to the fan and onwards to

the condenser unit.

On its way through the condenser the saturated

air releases its water content.The extracted water

falls into a holder, from which it is either pum-

ped up to a water tank or taken out via a drain

hose to a floor drain or similar.

COOLING AIR

The condenser is cooled by air at room tempera-

ture, drawn in through the rear of the machine.

The air is blown through the condenser and ex-

hausts through a grille in the bottom hatch. If

the machine is built in, the air is drawn through

the gap between the floor and the bottom of the

machine.

INSTALLATION

min

600

min

850

120

103

140 135

INSTALLATION

TUMBLE DRIER LOCATION

T720/780:

The tumble drier can be free-standing, built in or

part of a tower. Remember that the tumble drier

produces heat, and should therefore not be pla-

ced in too confined a space. If the tumble drier is

put into a very small room, because of the limi-

ted amount of air, the drying process will take

longer.

NOTE

To improve the air circulation, leave the door le-

ading into the room where the tumble drier is

placed open.

WARNING

The electrical installation must be carried out by

a qualified tradesman.

LOCATION ALTERNATIVES:

A. Free-standing

The tumble drier can be placed on the floor, either

on its own or up against a wall or cupboard.

B. Built-in

The tumble drier can be built in under a work

top with a minimum working height of 850 mm.

The width of the opening must be at least 600

mm.

C. Washing tower

The tumble drier can be placed on top of an ASKO

washing machine. The tumble drier is fastened

securely and prevented from moving by the to-

wer fasteners that come with the machine:

2 off angle pieces.

2 off plastic cups.

A pull-out worktop is available as an accessory

(Part no. 80 619 07-0 - white, 80 619 07-26 -

black), available for purchase from your local

ASKO dealer.

INSTALLATION

Install the tower configuration like this:

1. Unscrew and remove the outermost screws

from each side of the rear of the washing

machine.

2. Screw the angle pieces to the rear of the wash-

ing machine.

3. Secure the two plastic cups to the front edge

of the top cover.

WARNING

The plastic cups must be fitted, they secure the

front edge of the tumble drier.

Right side: Break off the left-hand tag from

one of the plastic cups and remove the paper

from the underside. Position the cup so that

the arm that sticks out is flush with the front

edge of the panel and press it firmly into pla-

ce.

Left side: Break off the right-hand tag from

the other plastic cup and remove the paper

from the underside. Position the cup so that

the arm that sticks out is flush with the front

edge of the panel and press it firmly into pla-

ce.

4. Position the tumble drier by fitting the two

angle pieces into the slots at the rear of the

tumble drier while keeping the front edge of

the tumble drier raised by 1 - 2 cm.

5. Lower the tumble drier so that its front feet

enter the plastic cups. Adjust the feet as neces-

sary to straighten the tumble drier vertical.

INSTALLATION

max 1000 mm

ADJUSTING THE FEET

Screw the feet in or out until the tumble drier is

standing vertical and steady. Lock the feet by tight-

ening their locking nuts.

CONDENSATION WATER (T720/780)

Alternative 1 (as delivered)

Condensation water is pumped up into the con-

densation water tank, which is pulled out and

emptied manually.

Alternative 2

By connecting the accompanying rubber hose to

the blue nipple and leading it down to a floor

drain, the condensation water is pumped directly

out to the drain.

Alternative 3

By connecting the accompanying rubber hose to

the blue nipple and leading it to a sink or similar,

condensation water is pumped directly out to the

drain.

INSTALLATION

ABC

AIR EXTRACTION (T700/760)

The exhaust air from the tumble drier should be

taken to an exhaust duct or a wall outlet with the

aid of the accompanying air extraction hose.

Connection to the tumble drier

The tumble drier has three possible air extraction

points: the rear, right or left side. On delivery one

of the holes is open, and the other two are closed

by covers.

The tumble drier is delivered with a connec-

ting flange (A), a plastic ring (B) and an air ex-

traction hose (C).

Install the air extraction system as follows:

1. Push the air extraction hose on to the connec-

ting flange and secure it with the plastic ring.

2. If necessary, remove the plastic cover from the

hole where you want to connect the hose.

3. Insert the connecting flange and air extraction

hose into the chosen hole.

4. Close the other two holes with the plastic

covers.

Connection to exhaust duct

The air extraction hose must be routed the short-

est possible way and as straight as possible from

the tumble drier to the exhaust duct. Cut the air

extraction hose if it is too long. If necessary the

air extraction hose can be extended by up to a

maximum of 8 metres (inner diameter 102 mm).

If a longer hose is needed, the inner diameter must

be increased in order to retain the fan capacity of

the tumble drier.

Any bends must be made as gentle as possible.

If 90º bends are necessary, there should be no more

than four. Each bend reduces the fan capacity of

the tumble drier.

If the air extraction hose leads to a wall outlet,

the entry of cold air can be cut down by installing

a ventilation grille (part no. 92 059 00).The ven-

tilation grille can be installed either outside or

inside.

If there is only one exhaust duct leading from

the room a draught break (A) must be installed

(part no. 92 059 01).

Andere Handbücher für T700 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Asko Trockner Handbücher

Beliebte Trockner Handbücher anderer Marken

Bosch

Bosch WTA79200GB Bedienungsanleitung

Amana

Amana W10233410A Bedienungsanleitung

Bosch

Bosch Logixx 10 WTB76556GB Technisches Datenblatt

Electrolux

Electrolux EW2H328R2 Bedienungsanleitung

Beko

Beko DS8433RX1M Bedienungsanleitung

Dawlance

Dawlance Spinner DS 6000 C Bedienungsanleitung

Electrolux

Electrolux TP5080TW Bedienungsanleitung

AEG

AEG TR838P4OB Bedienungsanleitung

Indesit

Indesit IDV 75 Bedienungsanleitung

Infiniton

Infiniton SD-DG85C Bedienungsanleitung

BOMANN

BOMANN WT 5019 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Bedienungsanleitung

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Bedienungsanleitung

Frigidaire

Frigidaire CAQE7077KW0 Betriebsanleitung

Bosch

Bosch WTX8HKM9SN Bedienungsanleitung

Sharp

Sharp KD-NHH9S7GW2-PL Bedienungsanleitung

Samsung

Samsung DV431AEPXAC Bedienungsanleitung

Speed Queen

Speed Queen ADE3TRW5431AW01 Bedienungsanleitung